Resolution RE116 Wireless Siren, 319.5MHz User Manual RE116 GE Siren Instructions
Resolution Products, Inc. Wireless Siren, 319.5MHz RE116 GE Siren Instructions
User Manual
RE116_GE_Siren_Instructions.doc Page 1 of 4 2/20/2012
www.ResolutionProducts.com
Wireless
Security
Solutions
RE116 Siren, GE
®
-Simon XT Compatible
Features
• Remote Wireless Siren
• For operation with Simon XT
• Responds to wireless alarm signal from panel
• Panel supervises Siren & Siren (optionally) supervises Panel
• Backup power on CR123A battery
• Cover tamper
• Unparalleled wireless range
• Low Battery indication
• 3x4x1.25 inches
Key Instructions
• Requires either Resolution RE920 or RE922 Alarm Communicator Cards, which
send wireless alarm signal.
• Engage Battery by removing pink isolator tab.
Battery “+” faces to right, away from tamper spring.
• Mode 1: Panel supervises Siren & Siren supervises Panel
Set switches
Press ENROLL switch on Simon Communicator board.
Put Panel in Enroll Mode.
Press & Release Siren Tamper to enroll Siren in Panel.
• Alternate Mode 2: Panel supervises Siren & Siren DOES NOT supervise Panel
Set switches
Put Panel in Enroll Mode.
Press & Release Siren Tamper to enroll Siren in Panel.
• Put Siren switches in RUN Mode:
1
2
1
2
1
2
RE116_GE_Siren_Instructions.doc Page 2 of 4 2/20/2012
www.ResolutionProducts.com
Operation
• Alarm
Siren follows panel alarm pattern.
• Supervision
Siren sends supervisory signals to panel IF:
Siren has AC power.
AND (if siren is set to supervise panel…)
Siren has heard signal from panel in previous 60 minutes.
• Tamper
When battery cover is opened.
Tamper Switch
F
unction
Switches
Yellow LED
• ON if AC present.
• Flashes on hearing
from Panel.
R
ed LED
• On if AC Present.
• Flashes short ON
when AC lost.
• Flashes evenly
ON/OFF in Enroll.
Battery “+”
B
attery
isolator tab.
Bemove.
RE116_GE_Siren_Instructions.doc Page 3 of 4 2/20/2012
www.ResolutionProducts.com
Specifications
Device Behavior: Siren Supervision acts like a Door/Window Battery &
Tamper
Supervisory Time 64-68 minutes
Alarm Patterns: Follows panel Siren ON/OFF Directly
Shortest ON pulse: 250 ms
Shortest OFF Pulse: 250 ms
Alarm Sound Intensity 85dB, minimum, at 1m
Receiver: Dual antenna diversity
Transmitter> Dual antenna Dirersity
Electrical Connection: US 2-prong Electrical outlet blades
Mounting hardware: Secure with outlet plate mounting screw
Terminal wire capacity: 16 Gauge
Replacement Battery: CR123A 1550 mAH
Temperature Range: 0F to 120F
Housing dimensions: 3x4x1.25 inches
Specifications subject to change without notice.
RE116_GE_Siren_Instructions.doc Page 4 of 4 2/20/2012
www.ResolutionProducts.com
Notices
“GE”, “Honeywell”, and “DSC” are trademarks owned by General Electric Company, Honeywell
International Inc., and Tyco Safety Products Canada LTD, respectively.
Resolution Products, Inc. products will function with one of either GE, DSC or Honeywell systems.
However, no Resolution product is produced by, endorsed by, nor is officially associated with GE,
Honeywell or DSC. Resolution recommends verifying proper enrollment and operation, per control
panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first year.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.
FCC ID: U5X-RE116
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son
fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interférences, et
2. Ce dispositif doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
IC: 8310A-RE116