Resolution RE211 Micro Door Window Sensor, 345MHz User Manual RE211 Honeywell Compat Micro DWS Instructions

Resolution Products, Inc. Micro Door Window Sensor, 345MHz RE211 Honeywell Compat Micro DWS Instructions

User Manual

RE211_Honeywell-Compat_Micro-DWS_Instructions.doc Page 1 of 4 9-Apr-12 www.ResolutionProducts.com RE211 Mighty Mouse™ Honeywell® -Compatible Micro Door Sensor Features • Smallest Door/Window Sensor & Magnet in the Industry. • Full-sized transmit range, AND… • 4-6 year battery life on CR1632 battery. • Invisible external antenna – gives great range and long life • Low Battery indication. Mounting Antenna Routing Options Wireless Security Solutions Run a light coat of permanent paste glue on the underside of the antenna wipe it down with finger Remove High Bond tape liners Align centering marks Position Antenna free and clear of sensor; not inside cover or under sensor. DON’T MOUNT ON METAL, It will severely reduce transmit range and magnetic gap A. Fasten with paste glue, as above. B. Or let it lay on surface, nearly invisibly. D. Drill hole and thread antenna down C. Route into trim gaps or along side of trim 1. 2. ½ inch or less magnet gap 3. 4. RE211_Honeywell-Compat_Micro-DWS_Instructions.doc Page 2 of 4 9-Apr-12 www.ResolutionProducts.com Enrolling in Panel . 1. Pull out the red tab to trip the sensor. This powers the sensor. 2. Put Honeywell or 2GIG panel in enrollment mode. Honeywell Panels 2GIG Panels 1. Put panel in RF Zone Programming mode. 2. Move magnet to and away (open/close, fault/restore) from sensor. 3. Will enroll as Loop 2. 1. Equip Type - Contact 2. Equip Code - 000 (other), or (0862) Thin door/window 3. Enter RF Serial # - Press Shift, Press Learn, 4. Trip Zone 5. (verify ID with ID on battery tab) 6. Equip Age - 0 (New) 7. Loop - 2 (Flood) Internal Picture Open/Close until Sensor enrolls in panel Sensor sends enrollment signal Battery Minus side up Reed Switch Antenna Battery contacts 1. 2.
RE211_Honeywell-Compat_Micro-DWS_Instructions.doc Page 3 of 4 9-Apr-12 www.ResolutionProducts.com Opening Cover Replacing Battery TO CLOSE slide cover jaw into hinge. Tilt closed. Insert Screwdriver in slot Tilt cover open. Hinge is in back away from antenna Insert Screwdriver in slot. Twist. Note small retention post 1. 2. RE211_Honeywell-Compat_Micro-DWS_Instructions.doc Page 4 of 4 9-Apr-12 www.ResolutionProducts.com Specifications Magnet trip distance: 1 inch nominal Supervisories: Hourly Battery Life: 4+ years Mounting fastener: 3M VHB (Very High Bond) Tape Replacement Battery: CR1632 Temperature Range: 0F to 120F Housing dimensions: 1.75 x 0.75 x 0.2 inches Antenna dimension: 2 inches Specifications subject to change without notice. Notices “GE”, “Honeywell”, “DSC” and “Napco” are trademarks owned by General Electric Company, Honeywell International Inc., Tyco Safety Products Canada LTD, and NAPCO Security Systems, Inc., respectively. Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco systems. However, no Resolution product is produced by, endorsed by, nor is officially associated with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and operation, per control panel installation instructions, at installation. Warranty Resolution Products, Inc. will replace products that are defective in their first year. FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the Resolution Products, Inc. could void the user's authority to operate this equipment. FCC ID: U5X-RE211 IC Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son fonctionnement est soumis aux deux conditions suivantes: 1. Ce dispositif ne peut causer des interférences, et 2. Ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. IC: 8310A-RE211

Navigation menu