Resolution RE211 Micro Door Window Sensor, 345MHz User Manual RE211 Honeywell Compat Micro DWS Instructions
Resolution Products, Inc. Micro Door Window Sensor, 345MHz RE211 Honeywell Compat Micro DWS Instructions
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1688505 |
| Application ID | 76HtpuTIf476kUqdX1jgRQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 28.8kB (359976 bits) |
| Date Submitted | 2012-05-02 00:00:00 |
| Date Available | 2012-05-03 00:00:00 |
| Creation Date | 2012-04-09 13:42:35 |
| Producing Software | GPL Ghostscript 8.64 |
| Document Lastmod | 2012-04-09 13:42:35 |
| Document Title | RE211_Honeywell-Compat_Micro-DWS_Instructions |
| Document Creator | PDFCreator Version 0.9.8 |
| Document Author: | bseemann |
Enrolling in Panel Wireless Security Solutions 1. Pull out the red tab to trip the sensor. This powers the sensor. 2. Put Honeywell or 2GIG panel in enrollment mode. Honeywell Panels 2GIG Panels RE211 Mighty Mouse™ Honeywell® -Compatible Micro Door Sensor 1. Put panel in RF Zone Programming mode. 2. Move magnet to and away (open/close, fault/restore) from sensor. 3. Will enroll as Loop 2. Features • • • • • 1. Smallest Door/Window Sensor & Magnet in the Industry. Full-sized transmit range, AND… 4-6 year battery life on CR1632 battery. Invisible external antenna – gives great range and long life Low Battery indication. Align centering marks Mounting 2. 1. 1. Equip Type - Contact 2. Equip Code - 000 (other), or (0862) Thin door/window 3. Enter RF Serial # Press Shift, Press Learn, 4. Trip Zone 5. (verify ID with ID on battery tab) 6. Equip Age - 0 (New) 7. Loop - 2 (Flood) 2. ½ inch or less magnet gap Sensor sends enrollment signal Remove High Bond tape liners Open/Close until Sensor enrolls in panel Position Antenna free and clear of sensor; not inside cover or under sensor. 4. wipe it down with finger Run a light coat of permanent paste glue on the underside of the antenna Internal Picture 3. Battery contacts Battery Minus side up Reed Switch Antenna Routing Options A. Fasten with paste glue, as above. B. Or let it lay on surface, nearly invisibly. Antenna DON’T MOUNT ON METAL, It will severely reduce transmit range and magnetic gap RE211_Honeywell-Compat_Micro-DWS_Instructions.doc C. Route into trim gaps or along side www.ResolutionProducts.com of trim D. Drill 9-Apr-12 Page 1 of 4 hole and thread antenna down RE211_Honeywell-Compat_Micro-DWS_Instructions.doc Page 2 of 4 9-Apr-12 www.ResolutionProducts.com Opening Cover Specifications Magnet trip distance: Supervisories: Battery Life: Mounting fastener: Replacement Battery: Temperature Range: Housing dimensions: Antenna dimension: 1 inch nominal Hourly 4+ years 3M VHB (Very High Bond) Tape CR1632 0F to 120F 1.75 x 0.75 x 0.2 inches 2 inches Specifications subject to change without notice. Insert Screwdriver in slot Notices “GE”, “Honeywell”, “DSC” and “Napco” are trademarks owned by General Electric Company, Honeywell International Inc., Tyco Safety Products Canada LTD, and NAPCO Security Systems, Inc., respectively. Tilt cover open. Hinge is in back away from antenna Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco systems. However, no Resolution product is produced by, endorsed by, nor is officially associated with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and operation, per control panel installation instructions, at installation. Warranty Resolution Products, Inc. will replace products that are defective in their first year. FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference that may be received, including interference that may cause undesired operation. TO CLOSE slide cover jaw into hinge. Tilt closed. Changes or modifications not expressly approved by the Resolution Products, Inc. could void the user's authority to operate this equipment. Replacing Battery 1. FCC ID: U5X-RE211 2. IC Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Insert Screwdriver in slot. Twist. Note small retention post Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son fonctionnement est soumis aux deux conditions suivantes: 1. Ce dispositif ne peut causer des interférences, et 2. Ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. IC: 8310A-RE211 RE211_Honeywell-Compat_Micro-DWS_Instructions.doc Page 3 of 4 RE211_Honeywell-Compat_Micro-DWS_Instructions.doc 9-Apr-12 www.ResolutionProducts.com Page 4 of 4 9-Apr-12 www.ResolutionProducts.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 2 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : 59f58441-84cf-11e1-0000-62794360beff Producer : GPL Ghostscript 8.64 Keywords : () Modify Date : 2012:04:09 13:42:35-05:00 Create Date : 2012:04:09 13:42:35-05:00 Creator Tool : \376\377\000P\000D\000F\000C\000r\000e\000a\000t\000o\000r\000 \000V\000e\000r\000s\000i\000o\000n\000 \0000\000.\0009\000.\0008 Document ID : 59f58441-84cf-11e1-0000-62794360beff Format : application/pdf Title : \376\377\000R\000E\0002\0001\0001\000_\000H\000o\000n\000e\000y\000w\000e\000l\000l\000-\000C\000o\000m\000p\000a\000t\000_\000M\000i\000c\000r\000o\000-\000D\000W\000S\000_\000I\000n\000s\000t\000r\000u\000c\000t\000i\000o\000n\000s Creator : \376\377\000b\000s\000e\000e\000m\000a\000n\000n Description : () Author : bseemann Subject :EXIF Metadata provided by EXIF.tools