Resolution RE352 Wireless Keypad, 433.92MHz User Manual RE352 DSC Compat PIN Pad

Resolution Products, Inc. Wireless Keypad, 433.92MHz RE352 DSC Compat PIN Pad

User Manual

RE352_DSC-Compat_PIN-Pad.doc Page 1 of 3 29-May-13 www.ResolutionProducts.com Wireless Security Solutions RE352 DSC-Compatible PINpad™ Features • Secure, 4-digit Code to disarm • 1-button arming • Red/Green LED arming feedback • Small, yet comfortable keypad • Mounts on wall via VHB® tape, or screws • Secure for carrying in purse or mounting on car visor • Strong, reliable RF signal. • 4-6 year battery life on CR2032 battery. Key Instructions • Enroll as a Key Fob. • Code programming Default access code is “1234”. To change access code: 1. Enter current 4-digit access code. 2. Within 4 seconds, press and hold the “1” and “3” keys simultaneously. After 3 seconds, Red LED will be lit. 3. Enter new 4-digit access code. After successfully changing the code, the Green LED will be lit 4. Note new access code . BAD GUY CANNOT RESET CODE. So it must be noted and remembered! • Enrolling: 1. Refer to the DSC control unit installation manual. 2. If panel is capable of Wireless Enrollment Mode, put the control panel in that mode and both the STAY or AWAY buttons for 3 seconds. Or, put panel in Serial Number Entry Mode and program in the printed ESN. 3. Set up as you would a WS4939 4-Button Fob. Operation PINpad Button Panel Action LED Stay ARM STAY flashes double red Away ARM AWAY flashes double red twice PIN Code DISARM flashes double green Stay + Away PANIC ALARM flashes red 8 times RE352_DSC-Compat_PIN-Pad.doc Page 2 of 3 29-May-13 www.ResolutionProducts.com Pictures Battery Replacement CR2032 Battery + Terminal up Insert Screwdriver here to open Red/Green Status LED Shows command sent Stay + Away = Panic (Enroll) TO CHANGE PIN CODE: Current 4-digit access code, and then… 1 + 3  Red LED,and then… Enter New Code
RE352_DSC-Compat_PIN-Pad.doc Page 3 of 3 29-May-13 www.ResolutionProducts.com Specifications Secure replacement to a DSC WS4939 4-Button Key Fob. Not supervised. Replacement Battery: CR2032 Lithium / Manganese Dioxide Temperature Range: 0F to 120F Housing dimensions: 2x2.25x0.33 inches 1-way RF: Does not receive panel status Specifications subject to change without notice. Notices “GE”, “Honeywell”, “DSC”, “2GIG” and “Napco” are trademarks owned by General Electric Company, Honeywell International Inc., Tyco Safety Products Canada LTD, 2GIG Technologies Inc., and NAPCO Security Systems, Inc., respectively. Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco systems. However, no Resolution product is produced by, endorsed by, nor is officially associated with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and operation, per control panel installation instructions, at installation. Warranty Resolution Products, Inc. will replace products that are defective in their first year. FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the Resolution Products, Inc. could void the user's authority to operate this equipment. FCC ID: U5X-RE352 IC Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec d’Industrie Canada RSS standard exempts de licence. Son fonctionnement est soumis aux deux conditions suivantes: 1. Ce dispositif ne peut causer des interférences, et 2. Ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. IC: 8310A-RE352

Navigation menu