Resolution RE627 Wireless NAPS Sleep Sensor User Manual

Resolution Products, Inc. Wireless NAPS Sleep Sensor

User Manual

Download: Resolution RE627 Wireless NAPS Sleep Sensor User Manual
Mirror Download [FCC.gov]Resolution RE627 Wireless NAPS Sleep Sensor User Manual
Document ID2384757
Application IDAGc8vkbJEIO3BO9sJsQWDw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize12.33kB (154101 bits)
Date Submitted2014-09-11 00:00:00
Date Available2014-09-13 00:00:00
Creation Date2014-09-10 08:20:15
Producing SoftwareOpenOffice 4.0.1
Document Lastmod0000-00-00 00:00:00
Document TitleUser Manual
Document CreatorWriter
Document Author: Benjamin Kyllo

RE627 Wireless NAPS Sleep Sensor - BTLE
Features:
• Pairs exclusively with Resolution Products Helix Panel receiver.
• Monitors patient's heart rate, breathing rate and restlessness through the provided
pressure sensor placed under bed sheets, no electrodes required.
• Wirelessly transmits patient's vitals to the Helix Panel receiver, then through the
internet to a monitoring center server.
• Screw on power supply cord and pressure sensor hose to protect against accidental
damage or disconnection.
Key Instructions:
• Attached external supply, screw the power cord onto the NAPS sensor connector.
• With the cover open, verify that the power LED starts to flash.
• Put Helix receiver into enrollment mode, press the button on the NAPS sensor.
◦ NAPS sensor says in enrollment mode for 15 seconds.
• Attach/screw on the pressure sensor hose to the NAPS sensor.
◦ Make the connection as finger tight as possible, however do not use tools as this
may damage the hose connector.
• Place pressure sensor on TOP of the mattress, but UNDER the sheets. Orient the
pressure sensor perpendicularly to body, and position the sensor directly under chest
plate, this will receive the best signal from the body.
LED Operation (for troubleshooting):
• Green power LED:
◦ Normal operation, the led will toggle on and off every 2 seconds.
◦ In enrollment mode, the led will toggle much faster, around every 1/4th second.
• Green and Red Heart rate LEDS:
◦ Once heart rate has established, the green and red leds will briefly flash for every
detected heart beat. If the heart beat is below 25bpm only the red led will flash
with the heart beat, if above 100bpm, both red and green will flash.
• Green and Red Breathing rate LEDS:
◦ Once breathing rate has established, the green and red leds will briefly flash for
every detected breath. If the breathing rate is below 6 breaths per minute, the
red led will flash with the breathing, if above 30 breaths per minute, both red
and green will flash.
• If movement is detected, the heart rate and breathing rate green LEDs will turn on
and stay on for as long as movement is detected.
Wireless NAPS Sleep
Sensor User Manual
http://resolutionproducts.com/
Page 1 of 3
•
•
After 5 seconds of no movement detected, the breathing rate and heart rate LEDs
will turn to red for 5 second.
If still no movement is detected after another 5 seconds, the breathing rate and
heart rate LEDs will flash yellow for 1 second to indicate all movement has stopped.
The LEDs will then resume flashing for the breathing rate and heart rate
measurements.
Specifications:
• External power supply: 6VDC. If using different supply, 100mA minimum required,
and 6-12VDC will work.
• Dimensions: 4 ¾” x 3 ¾” x 1”
• Internal antennas
• Bluetooth chip CC2541
Barrel power
connector
Enrollment button
Cover latch
Wireless NAPS Sleep
Sensor User Manual
Pressure sensor
Hose connector
http://resolutionproducts.com/
Page 2 of 3
Notices:
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Engineering, Inc.
or Lifeshield Inc. could void the user's authority to operate this equipment.
FCC ID: U5X-RE627
Model: RE627
Wireless NAPS Sleep
Sensor User Manual
http://resolutionproducts.com/
Page 3 of 3

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Language                        : en-US
Author                          : Benjamin Kyllo
Creator                         : Writer
Producer                        : OpenOffice 4.0.1
Create Date                     : 2014:09:10 08:20:15-05:00
EXIF Metadata provided by EXIF.tools
FCC ID Filing: U5X-RE627

Navigation menu