Rheem Professional Classic Plus Series Heavy Duty Power Direct Vent Specification Sheet

2015-04-02

: Rheem Rheem-Professional-Classic-Plus-Series-Heavy-Duty-Power-Direct-Vent-Specification-Sheet-683453 rheem-professional-classic-plus-series-heavy-duty-power-direct-vent-specification-sheet-683453 rheem pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

PRINTED IN U.S.A. 03/15 WP FORM NO. PRO+G RHPDVHD
INTEGRATED HOME COMFOR
T
INTEGRATED HOME COMFORT
Professional
Classic Plus
™ Heavy Duty Power
Direct Vent gas water heaters are a perfect choice
for tight construction and indoor air quality
Performance
• Recovery Capacity: 72.8 gallons per
hour (delivers approximately 120
gallons of hot water in the rst hour)**
Self-Diagnostic System
• Electronic gas control for
improved monitoring and
service
Low Emissions
• Eco-friendly burner, low NOx design
Features
• Two pipe system: one pipe pulls in
outside air for combustion and the
other exhausts combustion gases
• 120 VAC powered blower
• New whisper quiet blower
Flammable Vapor
Detection System
• Protective control system that
disables the heater in the presence of
ammable vapor accumulation
Flexible Venting Options
• Long venting lengths up to 100 feet
• PVC, ABS, or CPVC vent pipe options
• Vertical or horizontal termination
• Concentric vent kit available
Longer Life
• Premium grade anode rod provides
long-lasting tank protection
Plus…
• Enhanced ow brass drain valve
• Temperature and pressure relief valve
included
• Low lead compliant
• Durable silicon nitride igniter (HSI)
• Side taps for space heating
• EverKleen
™
patented system ghts
sediment build-up
• Standard replacement parts
Warranty
• 8-Year limited tank and parts warranty*
• With ProtectionPlus
™
the 8-year limited
tank warranty becomes 12-year
* See Residential Warranty Certicate for
complete information
Efficiency | All models tested according to ANSI test
procedures, and meet or exceed the thermal efciency
and standby loss requirements of current ASHRAE
standard (EPact). Also exceeds energy efciency
codes of all states including California Energy Com-
mission (CEC).
Safety and Construction | Design certied by CSA:
For operation at 160 degrees; meets all safety and
construction requirements of ANSI Z21.10.3; as an
automatic storage or instantaneous water heater; as
an automatic circulating tank water heater; and for
operation on combustible oors and in alcove installa-
tions. All models are North Carolina Code compliant.
Certified for 150 PSI maximum working pressure.
Professional
Classic Plus
Heavy Duty
Power Direct Vent
75-Gallon Capacities
75,100 Btu/h
Natural and LP Gas
LEED Point = 1
Water
INTEGRATED HOME COMFORT
Residential Gas
Professional
Classic Plus
Heavy Duty
Power Direct Vent Water Heaters
See specifications chart on back.
PRINTED IN U.S.A. 03/15 WP FORM NO. PRO+G RHPDVHD
2
In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.
Rheem Water Heating • 101 Bell Road
Montgomery, Alabama 36117-4305 • www.rheem.com
INTEGRATED HOME COMFOR
T
INTEGRATED HOME COMFORT
Vent and Combustion Air Inlet System Information
FROM SEA LEVEL THROUGH 2,000 FT. ABOVE SEA LEVEL
VENT & COMBUSTION AIR-INLET MIN. ALLOWED EQUIV. VENT & COMBUSTION MAX. ALLOWED EQUIV. VENT & COMBUSTION VENT AND COMBUSTION
MODEL SYSTEM DIAMETER (INCHES) AIR-INLET LENGTHS – EACH PIPE RUN (FT.) AIR-INLET LENGTHS – EACH PIPE RUN (FT.) AIR-INLET SYSTEM TERMINATION(S)
PRO+G75-76N RH PDV 3 8 50 90° Elbows –
PRO+G75-76N RH PDV 3 8 40 – Concentric*
PRO+G75-76N RH PDV 4 8 100 90° Elbows –
FROM 2,001 FT. ABOVE SEA LEVEL THROUGH 5,999 FT. ABOVE SEA LEVEL
VENT & COMBUSTION AIR-INLET MIN. ALLOWED EQUIV. VENT & COMBUSTION MAX. ALLOWED EQUIV. VENT & COMBUSTION VENT AND COMBUSTION
MODEL SYSTEM DIAMETER (INCHES) AIR-INLET LENGTHS – EACH PIPE RUN (FT.) AIR-INLET LENGTHS – EACH PIPE RUN (FT.) AIR-INLET SYSTEM TERMINATION(S)
PRO+G75-76N RH PDV 3 8 25 90° Elbows –
PRO+G75-76N RH PDV 3 8 20 – Concentric*
PRO+G75-76N RH PDV 4 8 100 90° Elbows –
FROM 6,000 FT. ABOVE SEA LEVEL THROUGH 7,700 FT. ABOVE SEA LEVEL
VENT & COMBUSTION AIR-INLET MIN. ALLOWED EQUIV. VENT & COMBUSTION MAX. ALLOWED EQUIV. VENT & COMBUSTION VENT AND COMBUSTION
MODEL SYSTEM DIAMETER (INCHES) AIR-INLET LENGTHS – EACH PIPE RUN (FT.) AIR-INLET LENGTHS – EACH PIPE RUN (FT.) AIR-INLET SYSTEM TERMINATION(S)
PRO+G75-76N RH PDV 4 8 50 90° Elbows –
One 90° elbow is approximately equivalent to 5 feet of pipe. One 45° elbow is approximately equivalent to 2.5 feet of pipe.
* Use only Rheem 3 inch concentric termination.
Water
INTEGRATED HOME COMFORT
Residential Gas
Professional
Classic Plus
Heavy Duty
Power Direct Vent Water Heaters
Professional
Classic Plus
™ Heavy Duty Power Direct Vent Specifications
DESCRIPTION FEATURES ROUGHING IN DIMENSIONS (SHOWN IN INCHES)
T HT. TO HT. TO HT. TO WATER HT. TO WATER FRONT
Y GAS INPUT IN RECOVERY IN TOP OF TOP OF TANK GAS CONN. SIDE T&P CONN. TO SHIP.
P GAL. MODEL THOUS. BTU/H G.P.H. 100° RISE** VENT AIR INLET HT. DIAM. CONN. CNTR. VALVE SIzE BACK WT.
E CAP. NUMBER NAT. LP NAT. LP A B C D E F G H I (LBS)
Tall 75 PRO+G75-76N RH PDV 75.1 – 72.8 – 70-3/8 71-1/4 60-1/2 26-1/4 15 11 53 1 36-3/4 325
Tall 75 PRO+G75-76P RH PDV – 75.1 – 72.8 70-3/8 71-1/4 60-1/2 26-1/4 15 11 53 1 36-3/4 325
D
CG
B A
E
T&P FITTING
3/4" N.P.T.
SIDE TAPS
1/2" HOT
WATER
CONNECTION
COMBUSTION
EXHAUST
(VENT)
COMBUSTION
AIR INLET
H
COLD
WATER
CONNECTION
H
F
I
**Recovery Capacity is based upon a 100° F water temperature rise and calculated per ANSI Z21.10.3 standards. First hour hot water delivery is based upon 77° water temperature rise.

Navigation menu