Rheem Professional Classic Series Power Vent Specification Sheet
2015-04-02
: Rheem Rheem-Professional-Classic-Series-Power-Vent-Specification-Sheet-683474 rheem-professional-classic-series-power-vent-specification-sheet-683474 rheem pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Residential Gas INTEGRATED H O M E C O M F O RT Classic Professional Water Power Vent Water Heaters Professional Classic™ Power Vent gas water heaters offer up to 100 foot vent runs, energy efficiency and the Guardian System Efficiency Flexible Venting Options • .67 EF • Long venting lengths up to 100 equivalent feet • Energy Star® rated Performance • FHR: 85 gallons for 50-gallon model and 71 gallons for 40-gallon model • Recovery rate is 36.4 for 50-gallon model and 32.4 for 40-gallon model at a 90 degree rise Self-Diagnostic System • PVC or CPVC certified to ULC-S636 vent pipe options • Vertical or horizontal termination Longer Life • Rheem exclusive R-Tech (resistored) anode rod provides long-lasting tank protection • Electronic gas control for improved monitoring and service High Altitude Compliant Low Emissions Plus… • Eco-friendly burner, low NOx design • Enhanced flow brass drain valve Features • Temperature and pressure relief valve included • Uses indoor air for combustion; blower exhausts the flue gases • Standard 120 VAC electrical connection • Certified for applications up to 6,000 feet above sea level • Low lead compliant • Durable Silicon Nitride Ignitor (HSI) • New whisper quiet blower • EverKleen patented system fights sediment build-up Guardian System™ & Sensor • Standard replacement parts ™ • Exclusive air/fuel shut-off device Warranty • Maintenance free – no filter to clean • 6-Year limited tank and parts warranty* • Disables the heater in the presence of flammable vapor accumulation Professional Classic Power Vent 40 and 50-Gallon Capacities Up to 36,000 Btu/h Natural and LP Gas LEED Point = 1 • With ProtectionPlus™ the 6-year limited tank warranty becomes 10-year *See Residential Warranty Certificate for complete information Combustion Shut-off System Flame Arrestor Plate Units meet or exceed ANSI requirements and have been tested according to D.O.E. procedures. Units meet or exceed the energy efficiency requirements of NAECA, ASHRAE standard 90, ICC Code and all state energy efficiency performance criteria. Maintenance Free See dimensions chart on back. IINNTTEEGGRAT ED MO FO RAT E DH OHM OEMCEOC MRT F O RT PRINTED IN U.S.A. 01/14 WP FORM NO. PROG RHPVCAN Residential Gas INTEGRATED HO M E C O M F O RT Classic Professional Water Power Vent Water Heaters Professional Classic™ Power Vent Specifications DESCRIPTION FEATURES ROUGHING IN DIMENSIONS (SHOWN IN INCHES) ENERGY INFO. T HT. TO HT. TO WATER HT. TO WATER GAS INPUT IN RECOVERY IN FIRST HOUR Y TOP OF TANK GAS CONN. SIDE T&P CONN. SHIP. ENERGY THOUS. BTU/H G.P.H. 90° RISE DEL. G.P.H. P GAL. MODEL ASSEMBLY HT. DIAM. CONN. CNTR. VALVE size WT. FACTOR E CAP. NUMBER NAT. LP NAT. LP NAT. A B C D E F G (LBS) NAT. AVG. ANNUAL OPER COST NAT. Short 40 PROG40S-36N CN67 PV 36 32 36.4 32.4 71 62-1/2 51-1/ 4 21-3/4 14 8 44-1/4 3/4 155 0.67 $272 Short 50 PROG50S-36N CN67 PV 36 32 36.4 32.4 85 62-1/ 2 51-1/4 14 8 44 3/4 175 0.67 $272 23-3/4 POWER VENT ASSEMBLY ANODE ROD G G HOT WATER CONNECTION E COLD WATER CONNECTION T&P FITTING 3/4" N.P.T. C A B F 1/2" D Maximum and Minimum Vent Lengths for 2” Vents Maximum and Minimum Vent Lengths for 3” Vents NumbER OF MINIMUM MAXIMUM MAXIMUM 90° ELBOWS NUMBER PIPE PIPE PIPE with Vent OF 45° length length (ft.) length (ft.) Terminal Elbows req. (ft.) 0’ - 2000’ 2000’ - 7700’ * NumbER OF MINIMUM MAXIMUM MAXIMUM 90° ELBOWS NUMBER PIPE PIPE PIPE with Vent OF 45° length length (ft.) length (ft.) Terminal Elbows req. (ft.) 0’ - 2000’ 2000’ - 7700’ * One (1) None 4.0 44.0 24.0 One (1) None 5.0 95.0 75.0 One (1) One (1) 4.0 41.0 21.0 One (1) One (1) 5.0 92.5 72.5 Two (2) None 4.0 38.0 18.0 Two (2) None 5.0 90.0 70.0 Two (2) One (1) 4.0 35.0 15.0 Two (2) One (1) 5.0 87.5 67.5 Three (3) None 4.0 32.0 12.0 Three (3) None 5.0 85.0 65.0 For the 2” vent, one 90° elbow is approximately equal to 6 feet of pipe. One 45° elbow is approximately equal to 3 feet of pipe. *2,000’ – 6,000’ for short models. For the 3” vent, one 90° elbow is approximately equal to 5 feet of pipe. One 45° elbow is approximately equal to 2.5 feet of pipe. *2,000’ – 6,000’ for short models. In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice. Rheem Canada Ltd./Ltée • 125 Edgeware Road, Unit 1 Brampton, Ontario L6Y 0P5 • www.rheem.com IINNTTEEGGRAT ED MO FO RAT E DH OHM OEMCEOC MRT F O RT PRINTED IN U.S.A. 01/14 WP FORM NO. PROG RHPVCAN
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2014:01:09 10:57:38-05:00 Metadata Date : 2014:01:09 10:57:41-05:00 Modify Date : 2014:01:09 10:57:41-05:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:a644dd73-859a-be43-8cee-dd0b7e1f24fc Original Document ID : xmp.did:0A80117407206811B34BA559CEB6FCA7 Document ID : xmp.id:9FBD21D044356811822AAFC53C065F3E Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:9EBD21D044356811822AAFC53C065F3E Derived From Document ID : xmp.did:15C5B64442356811822AAFC53C065F3E Derived From Original Document ID: xmp.did:0A80117407206811B34BA559CEB6FCA7 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2014:01:09 10:57:39-05:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 2 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools