Rhine Electronics Co 7234T4 Transmitter User Manual

Rhine Electronics Co Ltd Transmitter Users Manual

Manual

INSTRUCTIONS FOR OPERATIONSETING THE OPERATING CONTROLS1. This unit operates on a 3 volts battery  (not included).   To prevent possible damage if the battery should leak , be sure to remove   the battery when the unit is not use .2.  Store the controller away from excess heat or humidity .3.  This remote control unit is required with 24bit code combinations. To prevent possible interference from or to other remote units such as garage door openers, car alarm or security system .  4. Operation buttons on the panel of transmitter .                    LED display                 REV button – Fan reverseFAN OFF button -                        Warm weather/Cool weatherFAN  OFF                                                                                         FAN SPEED DOWN button –                                              FAN SPEED UP button –  fan speed (speed 6 to 1)                                                          Fan speed (speed 1 to 6)                                                                                     LIGHT button -                                                                                      Light ON/OFF or Dimmer              FAN TIMING button-2 hour/ 4 hour / 8 hour                                                                                                                                                     Natural wind button-                                                                                         Natural wind function Start/stop                                                                                                                                                                                                                                                                    10607181
                                                                        Light set Switch  –                                                                        For set light dimmer type  or light ON/OFF type control . 5. Start the fan Press the FAN speed  button  .6. Turn off the fan :Press the OFF button .7. Light control :Turn the light on or off  by only touching the LIGHT CONTROL  button .Keep pressing the button in excess of  0.7 second it becomes a dimmer ,the light varies cyclically in  0.8 second .8. Timing  set : 2H : 2 hours later, the fan is off4H : 4 hours later, the fan is off8H : 8 hours later, the fan is offGENERAL INFORMATION :This REMOTE controller is designed to separately control your ceiling fan speed and light brightness . The Light  ON/OFF button will control the light brightness ON/OFF .The LED indicator on the transmitter will light when the Function button is pressed .10607182
INSTRUCTIONS   FOR   INSTALLATION   AND   OPERATION   OF   FAN   SPEEDCONTROLLER1. Setting the code on your new transmitter .Within 60 seconds of turning the AC power on, press and hole the FAN ON/OFF button for 5 seconds. The receiver will then lock in the chosen frequency. If your fan has a light it it will blink twice, for fans without lights check operation using the transmitterNOTICE :  The changes or modifications not expressly approved by the      party responsible for compliance could void user’s authority       to operate the equipment .IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, nochange to the antenna or the device is permitted. Any change to the antenna or the devicecould result in the device exceeding the RF exposure requirements and void user’s authority tooperate the device.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause10607183
FCC INFORMATION        The Federal Communication Commission Radio Frequency InterferenceStatement includes the following paragraph:         The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference ina residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication.  However, there is no grantee that interference will not occur in a particular installation.  If this equipment dose cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for help.10607184

Navigation menu