Rhine Electronics Co GTX740 Transmitter of Remote Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	575063
Application ID	HEjLdxmJtsGi27S2QS7Qyw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7kB (87450 bits)
Date Submitted	2005-08-25 00:00:00
Date Available	2005-08-25 00:00:00
Creation Date	2005-07-05 13:22:33
Producing Software	Acrobat PDFWriter 5.0Windows NT ª©
Document Lastmod	0000-00-00 00:00:00
Document Title	Users Manual
Document Creator	GTX740英文使用手冊.doc - Microsoft Word
Document Author:	Administrator

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
MODEL:GTX740
Wireless Keyless Entry System (Optional Accessory)
Wireless Keypad Installation
1. Slide off both keypad and battery covers to fasten with 2 pan head screws.
2. Slide keypad cover onto Keypad.
3. Install a 9 volt battery and slide battery cover onto Keypad.
NOTE ：Mount Keypad out of child’s reach (at least 5 feet above floor).
Programming Wireless Keypad
1. Press and hold the “learn“ button (on the right side of the panel ) until
the green indicator light flashes (about 5 seconds )to erase old code.
2. Press and release the “learn” button (on the right side of the panel ).
3. When the green indicator light is illuminated, press 4 desirde
digits and ENTER to code Keypad.
NOTE ：When programming wireless keypad, the distance shall be at least 24
inches from the antenna of opener.
4. Enter the code to signal the system to open, close, stop or move the door
In the opposite direction.
You may set up this feature as follows:
1. Press and release the "learn" button (on the right side of
the panel).
2. When the green indicator light is illuminated, press and
hold the selected remote control push button.
3. After the green indicator light flashed three times,
release
the button.
4.This stores open/stop/close function for the selected
button for the first opener in memory.
5.Repeat the same steps above on the second and third
openers.
page: 1/2
Erase All Remote Control Codes
1. Press and hold the "learn" button (on the right side of the panel)
until the green indicator light flashes (about 5 seconds).
2. All transmitter codes are now erased.
Then follow the steps above to re-program each remote control.
Notice:The changes or modifications not expressly approved by the party responsible
For compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC rules .Operation is subject to the following two
conditions .
(1) This device may not cause harmful interference and
(2) This device must accept any interference received , Including interference that may
cause undesired operation .
The term “IC:” before the radio certification number only signifies that Industry
Canada Technical specifications were met.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
page: 2/2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Creator                         : GTX740英文使用手冊.doc - Microsoft Word
Create Date                     : 2005:07:05 13:22:33
Title                           : GTX740英文使用手冊.doc
Author                          : Administrator
Producer                        : Acrobat PDFWriter 5.0Windows NT ª©

EXIF Metadata provided by EXIF.tools