Rhine Electronics Co RH787T Transmitter of Remote Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	831257
Application ID	DaQnKQ/q2NWyOt1gSHH6qw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.94kB (11805 bits)
Date Submitted	2007-08-20 00:00:00
Date Available	2007-08-20 00:00:00
Creation Date	2007-07-27 09:34:55
Producing Software	Acrobat PDFWriter 5.0Windows NT ª©
Document Lastmod	0000-00-00 00:00:00
Document Title	Users Manual
Document Creator	RH787T操作手冊.DOC - Microsoft Word
Document Author:	Administrator

INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
1.This unit operates on a 12 volts battery (not included).
To prevent possible damage if the battery should leak , be sure to remove
the battery when the unit is not use .
2. Store the controller away from excess heat or humidity .
3. This remote control unit is required with 16 code combinations. To prevent
possible interference from or to other remote units such as garage door
openers, car alarm or security system . If you find that your fan and light
kit go on and off without using your control , simply change the combination
code in your transmitter and receiver .
4.Operation buttons on the panel of transmitter .
VI key – For fan Maximum speed .
V key – For fan high speed .
IV key – For fan Medium speed .
III key – For fan Low speed .
II key – For fan Lower speed .
I key – For fan Minimum speed .
OFF key – For fan speed off .
REV key – For fan speed Reverse .
CONTROL key – For light brightness and ON/OFF control .
SET key – For learn
5.Start the fan :
Press the selected speed button to run the fan at the desired .
6.Turn off the fan :
Press the OFF button .
7.Light control :
Turn the light on or off by only touching the LIGHT CONTROL button .
Keep pressing the button in excess of 0.7 second it becomes a dimmer ,
the light varies cyclically in 0.8 second .
One of the important feature of this control is AUTO-RESUME . After power
on , it allows the light return to where it was off .
910805
GENERAL INFORMATION :
This REMOTE controller is designed to separately control your
ceiling fan speed and light brightness . The Light
ON/OFF button will control the light brightness ON/OFF .
The red indicator on the transmitter will light when the button is pressed .
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN
SPEED CONTROLLER
A. Setting the code on your new transmitter .
1. Remove battery cover .
Press firmly below arrow and slide battery cover off .
2. Slide code switches to your choice of UP and DOWN position .
Factory setting is all UP . Do not use this setting .
Use ball point pen or small screwdriver .
Slide firmly up or down .
B. Setting the code on your new Receiver unit .
1. Slide code switches to the same positions as set on your transmitter .
They must be set to same positions to work .
2. Replace battery cover on transmitter .
3. Make sure the code switches are on the left positions .
NOTICE :
The changes or modifications not expressly approved by the
party responsible for compliance could void user’s authority
to operate the equipment .
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference
910805
received, including interference that may cause
910805

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 3
Creator                         : RH787T操作手冊.DOC - Microsoft Word
Create Date                     : 2007:07:27 09:34:55
Title                           : RH787T操作手冊.DOC
Author                          : Administrator
Producer                        : Acrobat PDFWriter 5.0Windows NT ª©

EXIF Metadata provided by EXIF.tools