Richen S205 Bluetooth Speaker User Manual

Richen Industrial Co.,Ltd Bluetooth Speaker

User manual

Diagonal Desktop Bluetooth® SpeakerInstruction Manual7198-45GY1 x Bluetooth® Speaker (7198-45GY)1 x USB to Micro-USB Charging Cable1 x 3.5mm Aux Line-in Cable1 x Instruction ManualPlaying time: up to 6 hrs at max volumeCharging time: up to 4 hrsPairing Name: “Diagonal BT”(Be sure to fully charge the speaker before using for the rst time).Charging the SpeakerOpen rubber seal cover, Connect the provided charging cable to a power source and to the micro USB port on the speaker (6).The LED indicator light will glow red when charging and turn off when fully charged.Bluetooth® Setup:Press and hold ON/OFF Button, LED Indictor will then ash BLUE and RED.Turn on the Bluetooth function on mobile device, Select “Diagonal BT” pairing name.LED will ash BLUE if successfully pairedSpeaker will automatically pair if the mobile device has been paired before.Press and hold ON/OFF button to turn off the deviceCall Function:Press (4) once to answer a incoming call, press and press again to end callPress and hold to reject the incoming callPress (4) twice to redial last called number from the speaker.AUX Function:Open rubber seal cover(6) to nd the speakers AUX-IN port, plug in supplied 3.5mm AUX cable into the port and connect to the mobile device.LED will turn BLUE when connected.WARNING-When using this product, basic precautions should always be followed:Read all the instructions before use.Never store or use this product in temperatures below 32°F(0°C) or above 115°F(45°C). The unit’s full performance is achieved only after 2 or 3 completed charge and discharge cycles. To reduce the risk of injury, close supervision is necessary when the product is used near children. Do not expose the device to moisture.Do not use the device in excess of its output rating. Overload outputs above rating may result in a risk of re or injury. Do not use the device if damaged or modied.Damaged or modied batteries may exhibit unpredictable behavior resulting in re, explosion or risk of injury. Do not disassemble the device. For repairs, seek a qualied service professional. Incorrect reassembly may result in a risk of re or injury. Do not expose the device to re or excessive temperature. Exposure to re or temperatures above 104°F may cause explosion.Ensure that qualied service professionals use only identical replacement parts to ensure product safety1. • 2. • • •* •3. • • •4. • ••1.2.3.4.5.6.7.8.9.10.11.1.2.3.4.5.6.•••LED IndicatorVol-/Previous Track:Vol- : Press and holdPrevious Track: Short pressVol+/Next Track:Vol+: Press and holdNext Track: Short pressPlay/Pause/Call FunctionON/OFF Button3.5mm AUX Line-in/Speaker ResetCharging PortWhat’s included:Functions:Tech SpecicationsInstructions:SAFETY PRECAUTIONS:MADE IN CHINAChanges or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment general uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.FCC Statement:

Navigation menu