Ridgid Gp90135 Users Manual

GP90135 to the manual 3d4bacd6-612f-4ab3-8a8d-064dcabecb82

2015-02-04

: Ridgid Ridgid-Gp90135-Users-Manual-387718 ridgid-gp90135-users-manual-387718 ridgid pdf

Open the PDF directly: View PDF .
Page Count: 13

Download
Open PDF In Browser	View PDF

GP90135
OPERATOR’S MANUAL

WHEELBARROW
AIR
COMPRESSOR

! WARNING

Read and follow all Safety Rules
before first use of this product.
IN610400AV

Printed in U.S.A.

Table of Contents
Section

Safety Instructions
Page

Section

Table of Contents . . . . . . . . . . . . . . . .2

Page

Maintenance . . . . . . . . . . . . . . . . . . .13
Maintenance Schedule . . . . . . . . . .13
Tank . . . . . . . . . . . . . . . . . . . . . . . . .14
Filter Removal, Inspection, and
Replacement . . . . . . . . . . . . . . . . . .14
Drive Belt . . . . . . . . . . . . . . . . . . . . .15
Storage . . . . . . . . . . . . . . . . . . . . . .15

Safety Instructions . . . . . . . . . . . . . . .3
Safety Signal Words . . . . . . . . . . . . .3
Before Using the Air
Compressor . . . . . . . . . . . . . . . . . . . .3
Spraying Precautions . . . . . . . . . . . .5
Breathable Air Warning . . . . . . . . . . .5
Warning Labels . . . . . . . . . . . . . . . . .6

Troubleshooting . . . . . . . . . . . . . . . .16

Glossary of Terms . . . . . . . . . . . . . . .7

Notes . . . . . . . . . . . . . . . . . . . . . . . . .19

Unpacking and Checking
Content . . . . . . . . . . . . . . . . . . . . . . . .8

Repair Parts . . . . . . . . . . . . . . . . . . .20

Getting to Know Your Air
Compressor . . . . . . . . . . . . . . . . . . . .8

Warranty . . . . . . . . . . . . . . . . . . . . . .24

Warning indicates
! WARNING a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.

This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols.

Caution indicates a
potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.

Safety Signal Words
Danger indicates
an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.

DANGER

CAUTION

Notice indicates
important information, that if not followed, may cause damage to equipment.

!NOTICE

Notes . . . . . . . . . . . . . . . . . . . . . . . . .22

Before Using the Air Compressor

Operating Your Air Compressor . . .10
Moisture in Compressed Air . . . . . .10
Lubricaton . . . . . . . . . . . . . . . . . . . .11
Start-up . . . . . . . . . . . . . . . . . . . . . .11
To Start Gasoline Engine . . . . . . . .12

deterioration, weakness or leakage.
Repair or replace defective items
before using.

Since the air compressor and other components (pump, spray guns, filters, lubricators, hoses, etc.) used make up a high
pressure pumping system, the following
safety precautions must be observed at
all times:
1. Read all manuals included with this product carefully. Be thoroughly familiar with the controls and
the proper use of the
equipment.

8. Check all fasteners at frequent intervals for proper tightness.
! WARNING

Never operate
compressor without
a beltguard. Compressors can start automatically without warning. Personal
injury or property damage
could occurfrom contact with
moving parts.

MANUAL

2. Follow all local safety codes as well
as the United States Occupational
Safety and Health Act (OSHA).
3. Only persons well acquainted with
these rules of safe operation should
be allowed to use the compressor.

9. Do not wear loose clothing or jewelry
that will get caught in the moving
parts of the unit.

4. Keep visitors away and NEVER allow
children in the work area.
5. Wear safety glasses and
use hearing protection
when operating the pump
or unit.

6. Do not stand on or use the pump or
unit as a handhold.
7. Before each use, inspect compressed
air system, fuel system and electrical
components for signs of damage,
2

CAUTION

Compressor parts
may be hot even if
the unit is stopped.

Safety Instructions (continued)
10. Keep fingers away from a running
compressor; fast moving and hot
parts will cause injury and/or burns.

repair in or near a flammable
gas or vapor. Never store flammable liquids or gases in the
vicinity of the compressor.

11. If the equipment should start to
vibrate abnormally, STOP the
engine/motor and check immediately
for the cause. Vibration is generally a
warning of trouble.

! WARNING

Carbon monoxide can
cause severe nausea,
fainting or death. Do
not operate unit
inside a closed building or a
poorly ventilated area.

! WARNING

NEVER refuel a running or hot engine.
Explosive fuel can cause fires
and severe burns. Avoid overfilling fuel tank.

13. To reduce fire hazard, keep
engine/motor exterior free of oil, solvent, or excessive grease.

12. Check fuel level before starting the
engine. Do not fill the gas tank
indoors. Wipe off any spilled gas
before starting the engine.

! WARNING

Never remove or attempt to
adjust safety valve. Keep safety
valve free from paint and other
accumulations.

DANGER

Gasoline vapor is highly flammable. Refill outdoors or only in
well ventilated areas. Do not
store, spill or use gasoline near
an open flame or heat devices
such as a stove, furnace, or
water heater, which utilize a
pilot light, or any device that
can create a spark. If gasoline
is accidentally spilled, move
unit away from the spill area
and avoid creating any source
of ignition until gasoline vapors
have dissipated.

17. STOP the engine whenever leaving the
work area, before cleaning, making
repairs or inspections. When cleaning,

DANGER

Never attempt to
repair or modify a
tank! Welding, drilling
or any other modification will
weaken the tank resulting in
damage from rupture or explosion. Always replace worn or
damaged tanks.

! WARNING

Motors, electrical
equipment and controls can cause electrical arcs
that will ignite a flammable gas
or vapor. Never operate or

15. Tanks rust from moisture build-up,
which weakens the tank. Make sure to
drain tank daily and inspect periodically for unsafe conditions such as rust
formation and corrosion.
4

18. Allow engine to cool before storing.

Spraying Precautions
ed area to prevent health and fire
hazards.

! WARNING

Do not spray flammable materials in
vicinity of open
flame or near ignition sources
including the compressor unit.

21. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from the
spraying area as possible to minimize overspray accumulation on the
compressor.

19. Do not smoke when spraying paint,
insecticides, or other flammable substances.

22. When spraying or cleaning with solvents or toxic chemicals, follow the
instructions provided by the chemical manufacturer.

20. Use a face mask/respirator when
spraying and spray in a well ventilat-

!
14. Do not tamper with governor setting
on engine. Overspeeding the unit
severely shortens engine life and may
also be very hazardous.

repairing or inspecting, make certain all
moving parts have stopped. Disconnect
the spark plug wire and keep the wire
away from the plug to prevent accidental starting.

16. Fast moving air will stir up dust and
debris which may be harmful.
Release air slowly when draining
moisture or depressurizing the compressor system.

DANGER

Breathable Air Warning
This compressor/pump is not equipped and should not be used “as
is” to supply breathing quality air. For any application of air for
human consumption, the air compressor/pump will need to be fitted
with suitable in-line safety and alarm equipment. This additional
equipment is necessary to properly filter and purify the air to meet
minimal specifications for Grade D breathing as described in
Compressed Gas Association Commodity Specification G 7.1 - 1966,
OSHA 29 CFR 1910. 134, and/or Canadian Standards Associations
(CSA).
DISCLAIMER OF WARRANTIES
In the event the compressor is used for the purpose of breathing air
application and proper in-line safety and alarm equipment is not
simultaneously used, existing warranties shall be voided, and
Campbell Hausfeld disclaims any liability whatsoever for any loss,
personal injury or damage.

Safety Instructions (continued)

Glossary of Terms

Warning Labels

ASME Safety Valve
A safety valve that automatically releases
the air if the air receiver (tank) pressure
exceeds the preset maximum.

Find and read all warning labels found on
the air compressor shown below

Amps or Amperage
A measure of the electrical force minus
the resistance on an electrical line.
Ridgid air compressors require 15 amps
for operation. Be sure the compressor
will operate on an electrical line with the
proper amps. If other appliances operate
on the same line, they will reduce the
available amps. If the amperage is not
adequate, the result will be blown fuses
or tripped circuits.

PSI (Pounds per Square Inch)
Measurement of the pressure exerted by
the force of the air. The actual psi output
is measured by a pressure gauge on the
compressor
SCFM (Standard Cubic Feet per
Minute)
Sometimes called CFM (Cubic Feet per
Minute). Measurement of air volume
delivered by the compressor.

Regulator
A control that adjusts the line pressure to
the proper amount needed to operate
spray guns and air tools.

Air Delivery
A combination of psi and SCFM. The air
delivery required by a tool is stated as
(number) SCFM at (number) psi. The
combination of these figures determines
what size unit is needed.

Tank Pressure Gauge
Indicates tank pressure in psi.

Air Tank Capacity
The volume of air stored in the tank and
available for immediate use. A large tank
allows the intermittent use of an air tool
with an air requirement higher than the
compressor’s rated delivery.

Cut-in/Cut-off Pressure
Specific psi at which a compressor starts
and stops while refilling the air tank.

Line Pressure Gauge
Displays the current line pressures. It is
regulated by the regulator knob.

Volts or Voltage
A measurement of the force of an electrical current.

DK724100AV 10003

Figure 1

Unpacking and Checking Contents
1. Remove the air compressor from the
carton.

1. Air Filter. The air filter keeps dirt and
debris from entering the compressor
pump.

! WARNING

2. Place the compressor on a secure,
stationary work surface and look it
over carefully.

For your own safety, never
operate unit until all assembly
steps are complete and until
you have read and understood
the entire operator’s manual.

! WARNING

Do not operate unit if damaged
during shipping, handling or
use. Damage may result in
bursting and cause injury or
property damage.

! WARNING

To reduce the risk of injury, if
any parts are missing, do not
attempt to assemble the air
compressor until the missing
parts are obtained and installed
correctly.

Beltguard

Filter

2 Dipstick
3 Safety Valve
4 Regulator

5
6

Add Oil

2. Dipstick. The dipstick measures the
oil level in the compressor pump (See
Figure 3).

Unloader

Fill
Line

3. ASME Safety Valve. This valve automatically releases air if the tank pressure exceeds the preset maximum.
4. Regulator Knob. This knob controls
air pressure to an air operated tool or
paint spray gun. Turning the knob
clockwise increases air pressure at
the outlet. Turning counterclockwise
will lower air pressure at the outlet.
Fully counterclockwise will shut off
the flow of air completely (See Figure
4).

Figure 3

Open

Attach
Hose
Figure 4

6. Unloader. The unloader controls the
engine rpm. When loaded, the engine
will run at maximum operating speed
and air will enter the tank. When
unloaded, the engine will slow to an
idle and air will vent to atmosphere.
7. Belt Guard. The belt guard encloses
the pulleys and drive belt. It protects
the user from moving parts and
directs cooling air to the compressor
pump

Tank
Drain

Figure 2

Max
Low

5. Tank Drain Valve. The tank drain
valve allows moisture to be removed
from the tank. Note that each tank
has its own tank drain valve.

Getting to Know Your Air Compressor
7

Dipstick

Operating Your Air Compressor

NOTICE

Before starting the compressor,
thoroughly read all component
instruction manuals, especially
the engine manual.

Drain liquid from tank daily.

All lubricated compressor pumps discharge some condensed water and oil
with the compressed air. Install appropriate water/oil removal equipment and controls as necessary for the intended application.

CAUTION

Do not attach air tools to open
end of the hose until start-up is
completed and unit checks OK.

Lubrication
!

Dipstick

CAUTION

Add Oil

THIS UNIT CONTAINS NO OIL!
Follow lubrication instructions
before operating compressor.

Max
Low

Remove the dipstick/ breather and fill
pump with 12 ounces of oil. Use single viscosity, ISO 100 (SAE 30), non-detergent
compressor oil; or Mobil 1® 5W30 or
10W30 synthetic oil may also be used.
Proper oil fill is illustrated in Figure 5.

Fill
Line

Figure 5

Start-Up

NOTICE

1. Fill engine with oil and gasoline per
instructions furnished with engine.

Failure to install appropriate
water/oil removal equipment
may result in damage to
machinery or workpiece.

2. Remove the compressor dipstick
breather and fill pump to the proper oil
level.
3. Turn regulator knob counterclockwise
to open air flow.

Moisture in Compressed Air
IMPORTANT: This condensation will
cause water spots in a paint job, especially when spraying other than water based
paints. If sandblasting, it will cause the
sand to cake and clog the gun, rendering
it ineffective.
A filter in the air line, located as near to the
gun as possible, will help eliminate this
moisture.

Moisture in compressed air will form into
droplets as it comes from an air compressor pump. When humidity is high or when
a compressor is in continuous use for an
extended period of time, this moisture will
collect in the tank. When using a paint
spray or sandblast gun, this water will be
carried from the tank through the hose,
and out of the gun as droplets mixed with
the spray material.

4. Turn manual unloader lever up to a
horizontal position to allow the compressor pump to run without compressing air. (See Figure 6).
Figure 6 - Manual Lever Unloaded Position

Operating Your Air Compressor
(continued)

Maintenance
! WARNING

To Start Gasoline Engine

Release all pressure from the
system before attempting to
install, service, relocate or perform any maintenance.

5. Move the choke lever to the CHOKE
position, turn the fuel lever ON, and
turn the engine stop switch to the ON
position.
6. Pull start grip lightly until resistance is
felt, and then pull briskly.
7. As the engine warms up, gradually
move the choke lever to the open position. See gas engine manual for more
details.
8. Run the compressor unloaded for
approximately 30 minutes to break in
the pump.
9. After approximately 30 minutes, move
the unloader lever down to the loaded
position and turn the regulator knob
clockwise (See Figures 7 and 8). The
compressor will begin to pump air into
the tank.
When maximum tank pressure is
reached, the compressor automatically
unloads, bringing the engine to idle. The
engine remains at idle until tank pressure
falls to a preset level. The engine then
accelerates and the compressor pumps
additional air into the tank.

Figure 7 - Manual Lever Loaded Position

Open

DANGER

Do not attempt to tamper with
the ASME safety valve!

In order to maintain efficient operation of
the compressor system, check the air filter weekly (per maintenance schedule),
oil level and gasoline level before each
use. The ASME safety valve should also
be checked weekly. Pull ring on safety
valve and allow the ring to snap back to
normal position. This valve automatically
releases air if the tank pressure exceeds
the preset maximum. If air leaks after the
ring has been released, or the valve is
stuck and cannot be actuated by the ring,
the ASME safety valve MUST be
replaced.

Figure 9

With engine OFF, clean debris from
engine, flywheel, tank, air lines and
pump cooling fins.
Figure 8 -Regulator Knob

Maintenance Schedule
Operation
Check Oil Level
Drain Tank

Daily
l
l

Check Air Filter

l
l

Check Safety Valve

Blow Dirt From Unit
Check Belt Tightness
Change Oil

Weekly Monthly 3 Months

Maintenance (continued)

Drive Belt

Tank

Belt stretch is a result of normal use.
When properly adjusted, the belt deflects
about 1/2” with five pounds of pressure
applied midway between the engine pulley and pump (See Figure 12).

DANGER

Never attempt to repair or modify a tank! Welding, drilling or
any other modification will
weaken the tank resulting in
damage from rupture or explosion. Always replace worn,
cracked or damaged tanks.

Tank Drain
Figure 10

NOTICE
Drain liquid from tank daily.
The tank should be carefully inspected at
a minimum of once a year. Look for
cracks forming near the welds. If a crack
is detected, remove pressure from tank
immediately and replace.

1/2” Deflection

To adjust drive belt tension:
1. Remove belt guard and loosen
engine brace.
2. Loosen the four fasteners holding the
engine to the baseplate.
3. Shift the engine in the proper direction. The belt must be properly
aligned when adjustment is made.
4. To align belt, lay a straight edge
against the face of the flywheel,
touching the rim at two places (See
Figure 13).
5. Adjust flywheel or engine pulley so
that the belt runs parallel to the
straight edge.
6. Use a gear puller to move the pulley
on the shaft and tighten fasteners.
7. Adjust brace and reinstall.

Figure 12

Touch Rim in
Two Places
Figure 13

Figure 11

Storage
Filter Removal, Inspection and Replacement
To change a filter, pull off the filter housing
cover. If filter element is dirty, replace element or entire filter.

1. When not in use, hose and compressor should be stored in a cool, dry
place.
2. Tanks should be drained of moisture.
Hose should be disconnected and
hung with open ends down to allow
any moisture to drain.

Straight Edge
Parallel With Belt

Troubleshooting

TROUBLE
Overheating

! WARNING

For your own safety do not try
and run the air compressor
while troubleshooting.
TROUBLE
Low discharge pressure

PROBABLE CAUSE
1. Poor ventilation

2. Dirty cooling surfaces

PROBABLE CAUSE
1. Air leaks

2. Leaking valves

REMEDY
1. Listen for escaping air.
Apply soap solution to all
fittings and connections.
Bubbles will appear at
points of leakage. Tighten
or replace leaking fittings
or connections
2. Remove head and inspect
for valve breakage, weak
valves, scored valve seats,
etc. Replace defective
parts and reassemble

3. Restricted air intake
4. Slipping belts

5. Blown gaskets
6. Low compression

Excessive belt wear

CAUTION

Be sure that the old head
gasket is replaced with a
new one each time the
head is removed
3. Clean the air filter element
4. Loosen engine clamping
bolts and move the engine
in a direction away from
the compressor, being sure
that the engine pulley is
perfectly aligned with the
flywheel. Tighten engine
clamping bolts. The belt
should deflect about 1/2”
under 5-lbs of force. Do
not “roll” belts over pulleys
5. Replace any gaskets
proven faulty on inspection
6. Low pressure can be due
to worn rings and cylinder
walls. Correction is made
by replacing the rings,
cylinders, and pistons as
required

1. Pulley out of alignment
2. Belt too loose or too tight
3. Belt slipping

4. Pulley wobbles

Unit stalls

1. Low engine idle
2. Improper lubrication
3. Low oil level
4. Defective unloader valve

Excessive noise
(knocking)

1. Loose engine or compressor pulley

2. Lack of oil in crankcase

3. Worn connecting rod
4. Worn piston pin bushing

REMEDY
1. Relocate the compressor
to an area where an ample
supply of cool, clean, dry
and well-circulated air is
available
2. Clean the cooling surfaces
of pump and motor/engine
1. Realign engine pulley with
compressor pulley
2. Adjust tension (See Drive
Belt Section)
3. Adjust tension or replace
belt (See Drive Belt
Section)
4. Check for worn crankshaft,
keyway or pulley bore
resulting from running the
compressor or motor with
loose pulleys. Check for
bent pulleys or bent crankshaft
1. Increase idle, refer to
engine manual for details
2. See LUBRICATION, under
Assembly
3. Check oil level. Fill if necessary
4. Replace
1. Loose engine or compressor pulleys are a very common cause of compressors
knocking. Tighten pulley
clamp bolts and set-screws
2. Check for proper oil level; if
low, check for possible
damage to bearings. Dirty
oil can cause excessive
wear
3. Replace connecting rod
4. Remove piston assemblies
from the compressor and
inspect for excess wear.
Replace excessively worn
piston pin or pistons, as
required

Troubleshooting
TROUBLE
Excessive noise
(knocking)
Continued

Notes
PROBABLE CAUSE

5. Worn bearings
6. Piston hitting the valve
plate

7. Noisy check valve
Oil in the discharge
air

1. Worn piston rings
2. Compressor air intake
restricted
3. Restricted breather
4. Excessive oil in compressor
5. Wrong oil viscosity

6. Connecting rod out of
alignment

REMEDY
5. Replace worn bearings
and change oil
6. Remove the compressor
head and valve plate and
inspect for carbon deposits
or other foreign matter on
top of piston. Replace
head and valve plate using
new gasket
7. Replace
1. Replace with new rings
2. Clean filter. Check for other
restrictions in the intake
system
3. Clean and check breather
for free operation
4. Drain down to full level
5. Use SAE 30 (ISO 100)
non-detergent compressor
oil
6. Replace rod

Repair Parts

Repair Parts
For Repair Parts, Call 1-800-4-RIDGID
1

Key Part
No Number

32
33

2
31

3
30

35
27
36

5
26
25

24
23
20
19

7
21

22
10

12
17

14 13

Key Part
No Number

Qty

Descriptons

Qty

BG220900AJ

Belt guard
assembly

ST083800AV

Oil drain
extension

ST026200AV

Setscrew

VT470000KB

Pump

BT023100AV

Belt

ST159001AJ

ST073915AV

Filter assembly

Compression
assembly

ST073916AV

Filter element

VT046300AP

Discharge tube

ST070827AV

Screw

PU015900AV

Flywheel

PU015400AV

Pulley

KE000900AV

3/16" Key

ST012200AV

Square head
set screw

V-215100AV

ASME Safety
valve

ST183700AV

Tee fitting

HF002401AV

Nipple

ST119704AV

Elbow fitting

BG208800AJ

Brace assembly

ST160000AV

Handle grip

NG002502AV

Engine

ST70625AV

Hex head screw

D-1403

Drain valve

AR052200CG

Tank

ST011200AV

Washer

AL014000AJ

Locknut

ST158300AV

Rubber foot

ST116400AV

Screw

WA005500AV

10" Pneumatic
wheel

AA021800AV

Axle rod

ST073613AV

Plug

ST128407AV

Throttle
unloader

CV006404AV

Throttle control

GA016705AV

Gauge, left

WL017600AV

Regulator

GA016709AV

Gauge, right

HF203300AV

Coupler

ST150100AV

Oil drain cap

Descriptons

Please provide following information:
-Model number
-Serial number (if any)
-Part description and number as shown in parts list

Notes

RIDGID® AIR COMPRESSOR LIMITED THREE YEAR WARRANTY AND 90DAY SATISFACTION GUARANTEE POLICY
This product is manufactured by The Campbell Group under a trademark license from Ridgid, Inc.
All warranty communications should be directed to The Campbell Group, attn: RIDGID air compressor technical service at (toll free) 1-800-4-RIDGID.

90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are dissatisfied with the performance of
this RIDGID air compressor for any reason you may return the air compressor to the dealer from
which it was purchased for a full refund or exchange. To receive a replacement air compressor you
must present proof of purchase and return all original equipment packaged with the original product. The replacement air compressor will be covered by the limited warrant for the balance of the
three-year warranty period.

WHAT IS COVERED UNDER THE LIMITED THREE YEAR WARRANTY
This warranty covers all defects in workmanship or materials in this RIDGID air compressor for the
three-year period from the date of purchase. This warranty is specific to this air compressor.
Warranties for other RIDGID products may vary.

HOW TO OBTAIN SERVICE
To obtain service for this RIDGID air compressor you must return it, freight prepaid, to a service
center authorized to repair RIDGID air compressors. You may obtain the location of the service center nearest you by calling (toll free) 1-800-4-RIDGID or by logging on to the RIDGID website at
www.ridgid.com. When requesting warranty service, you must present the proof of purchase documentation, which includes a date of purchase. The authorized service center will repair any faulty
workmanship, and either repair or replace any defective part, at our option at no charge to you.

Catalog No. ###
Model No. GP90135
Serial No. ___________
The model and serial numbers may be found on your
unit. You should record both model and serial number
in a safe place for future use.

WHAT IS NOT COVERED
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If
this compressor is used for commercial, industrial or rental purposes, the warranty will apply for
ninety (90) days from the date of purchase. Extreme Duty Contractor Compressors are not limited
to a ninety (90) day warranty when used in contractor applications. Four cylinder single-stage and
two-stage compressors are not limited to a ninety (90) day warranty when used in commercial or
industrial applications. Some States do not allow limitations on how long an implied warranty
lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY
RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products
in accordance with instructions provided in the owner’s manual(s) supplied with compressor.
D. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.
E. Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets, etc.
F. Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser must comply with the warranty given by the engine manufacturer which is
supplied with the product.
G. Additional items not covered under this warranty:
1. All Compressors
• Any component damaged in shipment or any failure caused by installing or operating unit
under conditions not in accordance with installation and operation guidelines or damaged by
contact with tools or surroundings. • Pump or valve failure caused by rain, excessive humidity, corrosive environments or other contaminants. • Cosmetic defects that do not interfere
with compressor functionality. • Rusted tanks, including but not limited to rust due to
improper drainage or corrosive environments. • Electric motors, check valves and pressure
switches after the first year of ownership. • Drain cocks. • Damage due to incorrect voltage
or improper wiring. • Other items not listed but considered general wear parts. • Pressure
switches, air governors and safety valves modified from factory settings.
2. Lubricated Compressors
• Pump wear or valve damage caused by using oil not specified. • Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance guidelines.
3. Belt Drive / Direct Drive / Gas Driven Compressors
• Belts. • Ring wear or valve damage from inadequate filter maintenance. • Manually adjusted load/unload and throttle control devices.

ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness
for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase.
The Campbell Group is not responsible for direct, indirect, incidental or consequential damages. Some states do not allow
limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights, which vary from state to state.

QUESTIONS OR COMMENTS
CALL 1-800-4-RIDGID
www.ridgid.com
Please have your Model Number and Serial Number on hand when calling.

Form No. ###

Printed in U.S.A. 12/03

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 13
Creator                         : QuarkXPress(tm) 6.0
Create Date                     : 2003:11:18 14:40:19
Producer                        : QuarkXPress(tm) 6.0
Title                           : Layout 1
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (D.O. white).%%+ (New Color Swatch 1).%%+ (PANTONE 158 C).%%+ (PANTONE Reflex Blue C).%%CMYKCustomColor: 0 0 0 0 (D.O. white).%%+ 0 0 0 1 (New Color Swatch 1).%%+ 0 .61 .97 0 (PANTONE 158 C).%%+ 1 .73 0 .02 (PANTONE Reflex Blue C).%%EndComments

EXIF Metadata provided by EXIF.tools

Ridgid Gp90135 Users Manual

GP90135 to the manual 3d4bacd6-612f-4ab3-8a8d-064dcabecb82

Navigation menu

Versions of this User Manual:

Views

Navigation