Ridgid Gp90135 Users Manual

GP90135 to the manual 3d4bacd6-612f-4ab3-8a8d-064dcabecb82

2015-02-04

: Ridgid Ridgid-Gp90135-Users-Manual-387718 ridgid-gp90135-users-manual-387718 ridgid pdf

Open the PDF directly: View PDF .
Page Count: 13

GP90135

OPERATOR’S MANUAL

WHEELBARROW

AIR

COMPRESSOR

Read and follow all Safety Rules

before first use of this product.

WARNING

IN610400AV Printed in U.S.A.

Table of Contents

Section Page

Table of Contents . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . .3

Safety Signal Words . . . . . . . . . . . . .3

Before Using the Air

Compressor . . . . . . . . . . . . . . . . . . . .3

Spraying Precautions . . . . . . . . . . . .5

Breathable Air Warning . . . . . . . . . . .5

Warning Labels . . . . . . . . . . . . . . . . .6

Glossary of Terms . . . . . . . . . . . . . . .7

Unpacking and Checking

Content . . . . . . . . . . . . . . . . . . . . . . . .8

Getting to Know Your Air

Compressor . . . . . . . . . . . . . . . . . . . .8

Operating Your Air Compressor . . .10

Moisture in Compressed Air . . . . . .10

Lubricaton . . . . . . . . . . . . . . . . . . . .11

Start-up . . . . . . . . . . . . . . . . . . . . . .11

To Start Gasoline Engine . . . . . . . .12

Section Page

Maintenance . . . . . . . . . . . . . . . . . . .13

Maintenance Schedule . . . . . . . . . .13

Tank . . . . . . . . . . . . . . . . . . . . . . . . .14

Filter Removal, Inspection, and

Replacement . . . . . . . . . . . . . . . . . .14

Drive Belt . . . . . . . . . . . . . . . . . . . . .15

Storage . . . . . . . . . . . . . . . . . . . . . .15

Troubleshooting . . . . . . . . . . . . . . . .16

Notes . . . . . . . . . . . . . . . . . . . . . . . . .19

Repair Parts . . . . . . . . . . . . . . . . . . .20

Notes . . . . . . . . . . . . . . . . . . . . . . . . .22

Warranty . . . . . . . . . . . . . . . . . . . . . .24

Safety Instructions

This manual contains information that is

very important to know and understand.

This information is provided for SAFETY

and to PREVENT EQUIPMENT PROB-

LEMS. To help recognize this informa-

tion, observe the following symbols.

Safety Signal Words

Danger indicates

an imminently haz-

ardous situation which, if not avoided,

WILL result in death or serious injury.

Warning indicates

a potentially haz-

ardous situation which, if not avoided,

COULD result in death or serious injury.

Caution indicates a

potentially haz-

ardous situation which, if not avoided,

MAY result in minor or moderate injury.

Notice indicates

important informa-

tion, that if not followed, may cause dam-

age to equipment.

NOTICE

CAUTION

WARNING

DANGER

Since the air compressor and other com-

ponents (pump, spray guns, filters, lubri-

cators, hoses, etc.) used make up a high

pressure pumping system, the following

safety precautions must be observed at

all times:

1. Read all manuals includ-

ed with this product care-

fully. Be thoroughly famil-

iar with the controls and

the proper use of the

equipment.

2. Follow all local safety codes as well

as the United States Occupational

Safety and Health Act (OSHA).

3. Only persons well acquainted with

these rules of safe operation should

be allowed to use the compressor.

4. Keep visitors away and NEVER allow

children in the work area.

5. Wear safety glasses and

use hearing protection

when operating the pump

or unit.

6. Do not stand on or use the pump or

unit as a handhold.

7. Before each use, inspect compressed

air system, fuel system and electrical

components for signs of damage,

deterioration, weakness or leakage.

Repair or replace defective items

before using.

8. Check all fasteners at frequent inter-

vals for proper tightness.

9. Do not wear loose clothing or jewelry

that will get caught in the moving

parts of the unit.

Before Using the Air Compressor

MANUAL

Never operate

compressor without

a beltguard. Com-

pressors can start automatical-

ly without warning. Personal

injury or property damage

could occurfrom contact with

moving parts.

WARNING

Compressor parts

may be hot even if

the unit is stopped.

CAUTION

16. Fast moving air will stir up dust and

debris which may be harmful.

Release air slowly when draining

moisture or depressurizing the com-

pressor system.

17.

STOP the engine whenever leaving the

work area, before cleaning, making

repairs or inspections. When cleaning,

repairing or inspecting, make certain all

moving parts have stopped. Disconnect

the spark plug wire and keep the wire

away from the plug to prevent acciden-

tal starting.

18. Allow engine to cool before storing.

10. Keep fingers away from a running

compressor; fast moving and hot

parts will cause injury and/or burns.

11. If the equipment should start to

vibrate abnormally, STOP the

engine/motor and check immediately

for the cause. Vibration is generally a

warning of trouble.

12. Check fuel level before starting the

engine. Do not fill the gas tank

indoors. Wipe off any spilled gas

before starting the engine.

13. To reduce fire hazard, keep

engine/motor exterior free of oil, sol-

vent, or excessive grease.

14. Do not tamper with governor setting

on engine. Overspeeding the unit

severely shortens engine life and may

also be very hazardous.

15.

Tanks rust from moisture build-up,

which weakens the tank. Make sure to

drain tank daily and inspect periodical-

ly for unsafe conditions such as rust

formation and corrosion

Safety Instructions (continued)

NEVER refuel a run-

ning or hot engine.

Explosive fuel can cause fires

and severe burns. Avoid over-

filling fuel tank.

WARNING

Gasoline vapor is highly flam-

mable. Refill outdoors or only in

well ventilated areas. Do not

store, spill or use gasoline near

an open flame or heat devices

such as a stove, furnace, or

water heater, which utilize a

pilot light, or any device that

can create a spark. If gasoline

is accidentally spilled, move

unit away from the spill area

and avoid creating any source

of ignition until gasoline vapors

have dissipated.

DANGER

Motors, electrical

equipment and con-

trols can cause electrical arcs

that will ignite a flammable gas

or vapor. Never operate or

WARNING

Carbon monoxide can

cause severe nausea,

fainting or death. Do

not operate unit

inside a closed building or a

poorly ventilated area.

WARNING

repair in or near a flammable

gas or vapor. Never store flam-

mable liquids or gases in the

vicinity of the compressor.

Never remove or attempt to

adjust safety valve. Keep safety

valve free from paint and other

accumulations.

WARNING

Never attempt to

repair or modify a

tank! Welding, drilling

or any other modification will

weaken the tank resulting in

damage from rupture or explo-

sion. Always replace worn or

damaged tanks.

DANGER

19. Do not smoke when spraying paint,

insecticides, or other flammable sub-

stances.

20. Use a face mask/respirator when

spraying and spray in a well ventilat-

ed area to prevent health and fire

hazards.

21. Do not direct paint or other sprayed

material at the compressor. Locate

compressor as far away from the

spraying area as possible to mini-

mize overspray accumulation on the

compressor.

22. When spraying or cleaning with sol-

vents or toxic chemicals, follow the

instructions provided by the chemi-

cal manufacturer.

Spraying Precautions

Do not spray flam-

mable materials in

vicinity of open

flame or near ignition sources

including the compressor unit.

WARNING

Breathable Air Warning

This compressor/pump is not equipped and should not be used “as

is” to supply breathing quality air. For any application of air for

human consumption, the air compressor/pump will need to be fitted

with suitable in-line safety and alarm equipment. This additional

equipment is necessary to properly filter and purify the air to meet

minimal specifications for Grade D breathing as described in

Compressed Gas Association Commodity Specification G 7.1 - 1966,

OSHA 29 CFR 1910. 134, and/or Canadian Standards Associations

(CSA).

DISCLAIMER OF WARRANTIES

In the event the compressor is used for the purpose of breathing air

application and proper in-line safety and alarm equipment is not

simultaneously used, existing warranties shall be voided, and

Campbell Hausfeld disclaims any liability whatsoever for any loss,

personal injury or damage.

DANGER

Safety Instructions (continued)

Find and read all warning labels found on

the air compressor shown below

Warning Labels ASME Safety Valve

A safety valve that automatically releases

the air if the air receiver (tank) pressure

exceeds the preset maximum.

PSI (Pounds per Square Inch)

Measurement of the pressure exerted by

the force of the air. The actual psi output

is measured by a pressure gauge on the

compressor

SCFM (Standard Cubic Feet per

Minute)

Sometimes called CFM (Cubic Feet per

Minute). Measurement of air volume

delivered by the compressor.

Air Delivery

A combination of psi and SCFM. The air

delivery required by a tool is stated as

(number) SCFM at (number) psi. The

combination of these figures determines

what size unit is needed.

Air Tank Capacity

The volume of air stored in the tank and

available for immediate use. A large tank

allows the intermittent use of an air tool

with an air requirement higher than the

compressor’s rated delivery.

Volts or Voltage

A measurement of the force of an electri-

cal current.

Amps or Amperage

A measure of the electrical force minus

the resistance on an electrical line.

Ridgid air compressors require 15 amps

for operation. Be sure the compressor

will operate on an electrical line with the

proper amps. If other appliances operate

on the same line, they will reduce the

available amps. If the amperage is not

adequate, the result will be blown fuses

or tripped circuits.

Regulator

A control that adjusts the line pressure to

the proper amount needed to operate

spray guns and air tools.

Tank Pressure Gauge

Indicates tank pressure in psi.

Line Pressure Gauge

Displays the current line pressures. It is

regulated by the regulator knob.

Cut-in/Cut-off Pressure

Specific psi at which a compressor starts

and stops while refilling the air tank.

Glossary of Terms

DK724100AV 10003

Figure 1

1. Remove the air compressor from the

carton.

2. Place the compressor on a secure,

stationary work surface and look it

over carefully.

Unpacking and Checking Contents

Do not operate unit if damaged

during shipping, handling or

use. Damage may result in

bursting and cause injury or

property damage.

WARNING

For your own safety, never

operate unit until all assembly

steps are complete and until

you have read and understood

the entire operator’s manual.

WARNING

To reduce the risk of injury, if

any parts are missing, do not

attempt to assemble the air

compressor until the missing

parts are obtained and installed

correctly.

WARNING

Figure 2

Getting to Know Your Air Compressor

1 Filter

2 Dipstick

3 Safety Valve

4 Regulator

5 Tank

Drain

6 Unloader

7 Beltguard

1. Air Filter. The air filter keeps dirt and

debris from entering the compressor

pump.

2. Dipstick. The dipstick measures the

oil level in the compressor pump (See

Figure 3).

3. ASME Safety Valve. This valve auto-

matically releases air if the tank pres-

sure exceeds the preset maximum.

4. Regulator Knob. This knob controls

air pressure to an air operated tool or

paint spray gun. Turning the knob

clockwise increases air pressure at

the outlet. Turning counterclockwise

will lower air pressure at the outlet.

Fully counterclockwise will shut off

the flow of air completely (See Figure

4).

5. Tank Drain Valve. The tank drain

valve allows moisture to be removed

from the tank. Note that each tank

has its own tank drain valve.

6. Unloader. The unloader controls the

engine rpm. When loaded, the engine

will run at maximum operating speed

and air will enter the tank. When

unloaded, the engine will slow to an

idle and air will vent to atmosphere.

7. Belt Guard. The belt guard encloses

the pulleys and drive belt. It protects

the user from moving parts and

directs cooling air to the compressor

pump

Dipstick

Add Oil Fill

Line

Max

Low

Figure 3

Close Open

Attach

Hose

Figure 4

All lubricated compressor pumps dis-

charge some condensed water and oil

with the compressed air. Install appropri-

ate water/oil removal equipment and con-

trols as necessary for the intended appli-

cation.

1110

Operating Your Air Compressor

Before starting the compressor,

thoroughly read all component

instruction manuals, especially

the engine manual.

NOTICE

Failure to install appropriate

water/oil removal equipment

may result in damage to

machinery or workpiece.

NOTICE

Drain liquid from tank daily.

NOTICE

Do not attach air tools to open

end of the hose until start-up is

completed and unit checks OK.

CAUTION

Moisture in Compressed Air

Moisture in compressed air will form into

droplets as it comes from an air compres-

sor pump. When humidity is high or when

a compressor is in continuous use for an

extended period of time, this moisture will

collect in the tank. When using a paint

spray or sandblast gun, this water will be

carried from the tank through the hose,

and out of the gun as droplets mixed with

the spray material.

IMPORTANT: This condensation will

cause water spots in a paint job, especial-

ly when spraying other than water based

paints. If sandblasting, it will cause the

sand to cake and clog the gun, rendering

it ineffective.

A filter in the air line, located as near to the

gun as possible, will help eliminate this

moisture.

Remove the dipstick/ breather and fill

pump with 12 ounces of oil. Use single vis-

cosity, ISO 100 (SAE 30), non-detergent

compressor oil; or Mobil 1®5W30 or

10W30 synthetic oil may also be used.

Proper oil fill is illustrated in Figure 5.

THIS UNIT CONTAINS NO OIL!

Follow lubrication instructions

before operating compressor.

CAUTION

Lubrication Dipstick

Add Oil Fill

Line

Max

Low

Figure 5

1. Fill engine with oil and gasoline per

instructions furnished with engine.

2. Remove the compressor dipstick

breather and fill pump to the proper oil

level.

3. Turn regulator knob counterclockwise

to open air flow.

4. Turn manual unloader lever up to a

horizontal position to allow the com-

pressor pump to run without com-

pressing air. (See Figure 6).

Start-Up

Figure 6 - Manual Lever Unloaded Position

1312

Operating Your Air Compressor

(continued)

5. Move the choke lever to the CHOKE

position, turn the fuel lever ON, and

turn the engine stop switch to the ON

position.

6. Pull start grip lightly until resistance is

felt, and then pull briskly.

7. As the engine warms up, gradually

move the choke lever to the open posi-

tion. See gas engine manual for more

details.

8. Run the compressor unloaded for

approximately 30 minutes to break in

the pump.

9. After approximately 30 minutes, move

the unloader lever down to the loaded

position and turn the regulator knob

clockwise (See Figures 7 and 8). The

compressor will begin to pump air into

the tank.

When maximum tank pressure is

reached, the compressor automatically

unloads, bringing the engine to idle. The

engine remains at idle until tank pressure

falls to a preset level. The engine then

accelerates and the compressor pumps

additional air into the tank.

To Start Gasoline Engine

Figure 7 - Manual Lever Loaded Position

Figure 8 -Regulator Knob

Open

In order to maintain efficient operation of

the compressor system, check the air fil-

ter weekly (per maintenance schedule),

oil level and gasoline level before each

use. The ASME safety valve should also

be checked weekly. Pull ring on safety

valve and allow the ring to snap back to

normal position. This valve automatically

releases air if the tank pressure exceeds

the preset maximum. If air leaks after the

ring has been released, or the valve is

stuck and cannot be actuated by the ring,

the ASME safety valve MUST be

replaced.

With engine OFF, clean debris from

engine, flywheel, tank, air lines and

pump cooling fins.

Maintenance

Release all pressure from the

system before attempting to

install, service, relocate or per-

form any maintenance.

WARNING

Do not attempt to tamper with

the ASME safety valve!

DANGER

Figure 9

Operation Daily Weekly Monthly 3 Months

Check Oil Level l

Drain Tank l

Check Air Filter l

Check Safety Valve l

Blow Dirt From Unit l

Check Belt Tightness l

Change Oil l

Maintenance Schedule

1514

To change a filter, pull off the filter housing

cover. If filter element is dirty, replace ele-

ment or entire filter.

Filter Removal, Inspection and Replacement

Maintenance (continued)

Belt stretch is a result of normal use.

When properly adjusted, the belt deflects

about 1/2” with five pounds of pressure

applied midway between the engine pul-

ley and pump (See Figure 12).

To adjust drive belt tension:

1. Remove belt guard and loosen

engine brace.

2. Loosen the four fasteners holding the

engine to the baseplate.

3. Shift the engine in the proper direc-

tion. The belt must be properly

aligned when adjustment is made.

4. To align belt, lay a straight edge

against the face of the flywheel,

touching the rim at two places (See

Figure 13).

5. Adjust flywheel or engine pulley so

that the belt runs parallel to the

straight edge.

6. Use a gear puller to move the pulley

on the shaft and tighten fasteners.

7. Adjust brace and reinstall.

Drive Belt

1/2” Deflection

Figure 12

Touch Rim in

Two Places

Straight Edge

Parallel With Belt

Figure 13

1. When not in use, hose and compres-

sor should be stored in a cool, dry

place.

Tanks should be drained of moisture.

Hose should be disconnected and

hung with open ends down to allow

any moisture to drain.

Storage

The tank should be carefully inspected at

a minimum of once a year. Look for

cracks forming near the welds. If a crack

is detected, remove pressure from tank

immediately and replace.

Tank

Never attempt to repair or modi-

fy a tank! Welding, drilling or

any other modification will

weaken the tank resulting in

damage from rupture or explo-

sion. Always replace worn,

cracked or damaged tanks.

DANGER

Drain liquid from tank daily.

NOTICE

Figure 11

Figure 10

Tank Drain

1716

Troubleshooting

For your own safety do not try

and run the air compressor

while troubleshooting.

WARNING

TROUBLE PROBABLE CAUSE REMEDY

Low discharge pres-

sure

1. Air leaks

2. Leaking valves

3. Restricted air intake

4. Slipping belts

5. Blown gaskets

6. Low compression

1. Listen for escaping air.

Apply soap solution to all

fittings and connections.

Bubbles will appear at

points of leakage. Tighten

or replace leaking fittings

or connections

2. Remove head and inspect

for valve breakage, weak

valves, scored valve seats,

etc. Replace defective

parts and reassemble

Be sure that the old head

gasket is replaced with a

new one each time the

head is removed

3. Clean the air filter element

4. Loosen engine clamping

bolts and move the engine

in a direction away from

the compressor, being sure

that the engine pulley is

perfectly aligned with the

flywheel. Tighten engine

clamping bolts. The belt

should deflect about 1/2”

under 5-lbs of force. Do

not “roll” belts over pulleys

5. Replace any gaskets

proven faulty on inspection

6. Low pressure can be due

to worn rings and cylinder

walls. Correction is made

by replacing the rings,

cylinders, and pistons as

required

CAUTION

TROUBLE PROBABLE CAUSE REMEDY

Overheating

Excessive belt wear

Unit stalls

Excessive noise

(knocking)

1. Poor ventilation

2. Dirty cooling surfaces

1. Pulley out of alignment

2. Belt too loose or too tight

3. Belt slipping

4. Pulley wobbles

1. Low engine idle

2. Improper lubrication

3. Low oil level

4. Defective unloader valve

1. Loose engine or com-

pressor pulley

2. Lack of oil in crankcase

3. Worn connecting rod

4. Worn piston pin bushing

1. Relocate the compressor

to an area where an ample

supply of cool, clean, dry

and well-circulated air is

available

2. Clean the cooling surfaces

of pump and motor/engine

1. Realign engine pulley with

compressor pulley

2. Adjust tension (See Drive

Belt Section)

3. Adjust tension or replace

belt (See Drive Belt

Section)

4. Check for worn crankshaft,

keyway or pulley bore

resulting from running the

compressor or motor with

loose pulleys. Check for

bent pulleys or bent crank-

shaft

1. Increase idle, refer to

engine manual for details

2. See LUBRICATION, under

Assembly

3. Check oil level. Fill if nec-

essary

4. Replace

1. Loose engine or compres-

sor pulleys are a very com-

mon cause of compressors

knocking. Tighten pulley

clamp bolts and set-screws

2. Check for proper oil level; if

low, check for possible

damage to bearings. Dirty

oil can cause excessive

wear

3. Replace connecting rod

4. Remove piston assemblies

from the compressor and

inspect for excess wear.

Replace excessively worn

piston pin or pistons, as

required

1918

Troubleshooting

TROUBLE PROBABLE CAUSE REMEDY

Excessive noise

(knocking)

Continued

Oil in the discharge

air

5. Worn bearings

6. Piston hitting the valve

plate

7. Noisy check valve

1. Worn piston rings

2. Compressor air intake

restricted

3. Restricted breather

4. Excessive oil in compres-

sor

5. Wrong oil viscosity

6. Connecting rod out of

alignment

5. Replace worn bearings

and change oil

6. Remove the compressor

head and valve plate and

inspect for carbon deposits

or other foreign matter on

top of piston. Replace

head and valve plate using

new gasket

7. Replace

1. Replace with new rings

2. Clean filter. Check for other

restrictions in the intake

system

3. Clean and check breather

for free operation

4. Drain down to full level

5. Use SAE 30 (ISO 100)

non-detergent compressor

oil

6. Replace rod

Notes

2120

Repair Parts Repair Parts

For Repair Parts, Call 1-800-4-RIDGID

Please provide following information:

-Model number

-Serial number (if any)

-Part description and number as shown in parts list

Key Part

No Number Descriptons Qty

1 BG220900AJ Belt guard 1

assembly

2 ST026200AV Setscrew 1

3 BT023100AV Belt 1

4 ST073915AV Filter assembly 1

5 ST073916AV Filter element 1

6 ST070827AV Screw 4

7 V-215100AV ASME Safety 1

valve

8 ST183700AV Tee fitting 1

9 HF002401AV Nipple 1

10 ST119704AV Elbow fitting 2

11 ST160000AV Handle grip 2

12 D-1403 Drain valve 2

13 AR052200CG Tank 1

14 ST158300AV Rubber foot 4

15 ST116400AV Screw 4

16 WA005500AV 10" Pneumatic 1

wheel

17 AA021800AV Axle rod 1

18 ST073613AV Plug 2

19 ST128407AV Throttle 1

unloader

20 CV006404AV Throttle control 1

21 GA016705AV Gauge, left 1

22 WL017600AV Regulator 1

23 GA016709AV Gauge, right 1

24 HF203300AV Coupler 2

25 ST150100AV Oil drain cap 1

Key Part

No Number Descriptons Qty

26 ST083800AV Oil drain 1

extension

27 VT470000KB Pump 1

28 ST159001AJ Compression 1

assembly

29 VT046300AP Discharge tube 1

30 PU015900AV Flywheel 1

31 PU015400AV Pulley 1

32 KE000900AV 3/16" Key 1

33 ST012200AV Square head 1

set screw

34 BG208800AJ Brace assembly 1

35 NG002502AV Engine 1

36 ST70625AV Hex head screw 4

37 ST011200AV Washer 8

38 AL014000AJ Locknut 4

37 38

2322

Notes Notes

RIDGID®AIR COMPRESSOR LIMITED THREE YEAR WARRANTY AND 90-

DAY SATISFACTION GUARANTEE POLICY

This product is manufactured by The Campbell Group under a trademark license from Ridgid, Inc.

All warranty communications should be directed to The Campbell Group, attn: RIDGID air compres-

sor technical service at (toll free) 1-800-4-RIDGID.

90-DAY SATISFACTION GUARANTEE POLICY

During the first 90 days after the date of purchase, if you are dissatisfied with the performance of

this RIDGID air compressor for any reason you may return the air compressor to the dealer from

which it was purchased for a full refund or exchange. To receive a replacement air compressor you

must present proof of purchase and return all original equipment packaged with the original prod-

uct. The replacement air compressor will be covered by the limited warrant for the balance of the

three-year warranty period.

WHAT IS COVERED UNDER THE LIMITED THREE YEAR WARRANTY

This warranty covers all defects in workmanship or materials in this RIDGID air compressor for the

three-year period from the date of purchase. This warranty is specific to this air compressor.

Warranties for other RIDGID products may vary.

HOW TO OBTAIN SERVICE

To obtain service for this RIDGID air compressor you must return it, freight prepaid, to a service

center authorized to repair RIDGID air compressors. You may obtain the location of the service cen-

ter nearest you by calling (toll free) 1-800-4-RIDGID or by logging on to the RIDGID website at

www.ridgid.com. When requesting warranty service, you must present the proof of purchase docu-

mentation, which includes a date of purchase. The authorized service center will repair any faulty

workmanship, and either repair or replace any defective part, at our option at no charge to you.

WHAT IS NOT COVERED

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PUR-

POSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If

this compressor is used for commercial, industrial or rental purposes, the warranty will apply for

ninety (90) days from the date of purchase. Extreme Duty Contractor Compressors are not limited

to a ninety (90) day warranty when used in contractor applications. Four cylinder single-stage and

two-stage compressors are not limited to a ninety (90) day warranty when used in commercial or

industrial applications. Some States do not allow limitations on how long an implied warranty

lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY

RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PROD-

UCT. Some States do not allow the exclusion or limitations of incidental or consequential dam-

ages, so the above limitation or exclusion may not apply to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products

in accordance with instructions provided in the owner’s manual(s) supplied with compressor.

D. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.

E. Items or service that are normally required to maintain the product, i.e. lubricants, filters and gas-

kets, etc.

F. Gasoline engines and components are expressly excluded from coverage under this limited war-

ranty. The Purchaser must comply with the warranty given by the engine manufacturer which is

supplied with the product.

G. Additional items not covered under this warranty:

1. All Compressors

• Any component damaged in shipment or any failure caused by installing or operating unit

under conditions not in accordance with installation and operation guidelines or damaged by

contact with tools or surroundings. • Pump or valve failure caused by rain, excessive humidi-

ty, corrosive environments or other contaminants. • Cosmetic defects that do not interfere

with compressor functionality. • Rusted tanks, including but not limited to rust due to

improper drainage or corrosive environments. • Electric motors, check valves and pressure

switches after the first year of ownership. • Drain cocks. • Damage due to incorrect voltage

or improper wiring. • Other items not listed but considered general wear parts. • Pressure

switches, air governors and safety valves modified from factory settings.

2. Lubricated Compressors

• Pump wear or valve damage caused by using oil not specified. • Pump wear or valve dam-

age caused by any oil contamination or by failure to follow proper oil maintenance guidelines.

3. Belt Drive / Direct Drive / Gas Driven Compressors

• Belts. • Ring wear or valve damage from inadequate filter maintenance. • Manually adjust-

ed load/unload and throttle control devices.

ADDITIONAL LIMITATIONS

To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS

FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness

for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase.

The Campbell Group is not responsible for direct, indirect, incidental or consequential damages. Some states do not allow

limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or conse-

quential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you

may also have other rights, which vary from state to state.

QUESTIONS OR COMMENTS

CALL 1-800-4-RIDGID

www.ridgid.com

Please have your Model Number and Serial Number on hand when calling.

Part No. ### Form No. ### Printed in U.S.A. 12/03

Catalog No. ###

Model No. GP90135 Serial No. ___________

The model and serial numbers may be found on your

unit. You should record both model and serial number

in a safe place for future use.

Ridgid Gp90135 Users Manual

GP90135 to the manual 3d4bacd6-612f-4ab3-8a8d-064dcabecb82

Navigation menu

Versions of this User Manual:

Views

Navigation