Rimage RAS26E Professional 3400/ Professional 5400N User Manual 2001431 A 3400 5400N UG indd

Rimage Corporation Professional 3400/ Professional 5400N 2001431 A 3400 5400N UG indd

Manual

Rimage Professional™ 3400 and 5400N User Guide
2001431_ACorporate Headquarters:Rimage Corpora on7725 Washington Avenue SouthMinneapolis, MN 55439USA800-553-8312 (toll free US)Service: +1 952-946-0004 (Asia/Pacifi c, Mexico/La n America)Fax: +1 952-944-6956European Headquarters:Rimage Europe GmbHAlbert-Einstein-Str. 2663128 Dietzenbach GermanyTel: +49-(0) 6074-8521-0Fax: +49-(0) 6074-8521-100Rimage Corpora on reserves the right to make improvements to the equipment and so ware described in this document at any  me without any prior no ce. Rimage Corpora on reserves the right to revise this publica on and to make changes from  me to  me in the content hereof without obliga on of Rimage Corpora on to no fy any person or organiza on of such revisions or changes.This document may contain links to web sites that were current at the  me of publica on, but may have moved or become inac ve since. This document may contain links to sites on the Internet that are owned and operated by third par es. Rimage Corpora on is not responsible for the content of any such third-party site.©2010, Rimage Corpora onRimage® is a registered trademark of the Rimage Corpora on. Professional™ and Everest™ are trademarks of the Rimage Corpora on. Dell™ is trademark of Dell Computer Corpora on. FireWire™ is a trademark of Apple Computer, Inc. Windows® is a registered trademark of Microso Corpora on.All other trademarks and registered trademarks are the property of their respec ve owners.2001431_A
2001431_AContentsIntroduc on .......................................................................................................................................5About this User Guide .............................................................................................................................................................. 5About the Professional 3400 and 5400N ................................................................................................................................. 5Accessory Kit ............................................................................................................................................................................ 6Unpacking and Setup Instruc ons ........................................................................................................................................... 6Important Informa on .......................................................................................................................7Support Informa on ................................................................................................................................................................ 7Learn More Online ................................................................................................................................................................... 7Technical Support .................................................................................................................................................................... 7Op cal Disc Recording So ware Disclaimer ............................................................................................................................ 8Safety and Compliance Informa on ........................................................................................................................................ 8Safety Precau ons ..................................................................................................................................................................................... 8Country-specifi c Cau ons and Warnings for Wideband Data Transmission Systems: 2400-2483.5 MHz ................................................. 9Compliance Informa on ............................................................................................................................................................................ 9Professional 3400 and 5400N Specifi ca ons ......................................................................................................................... 10Everest 400 Printer Specifi ca ons .......................................................................................................................................... 12Printer Requirements ....................................................................................................................... 13Ribbon Requirements ............................................................................................................................................................ 13Everest 400 Ribbons ................................................................................................................................................................................ 13Label Design Requirements ................................................................................................................................................... 14Print Requirements ................................................................................................................................................................ 14Iden fy the Parts of the Professional 3400 and 5400N ......................................................................15Front View .............................................................................................................................................................................. 15Back View ............................................................................................................................................................................... 163400 ......................................................................................................................................................................................................... 165400N ...................................................................................................................................................................................................... 16Parts Informa on ................................................................................................................................................................... 17Control Panel ........................................................................................................................................................................................... 17Control Panel Indicators ......................................................................................................................................................................... 17PC Power Bu on ...................................................................................................................................................................................... 17Disc Dispenser ......................................................................................................................................................................................... 17Operate the Professional 3400 and 5400N System ............................................................................ 19Power On the System ............................................................................................................................................................. 19Power Off the System ............................................................................................................................................................ 19Pause the System ................................................................................................................................................................... 20Load the Discs ........................................................................................................................................................................ 20Unload the Discs .................................................................................................................................................................... 20Place a Disc on the Printer Tray ............................................................................................................................................. 21Place a Disc on the Recorder Tray .......................................................................................................................................... 21Set Your Prin ng Preferences on a Windows PC ................................................................................23Access Prin ng Preferences .................................................................................................................................................................... 23Access Prin ng Preferences through the Windows Start Menu .................................................................................................................................... 23Access Printer Preferences through CD Designer .......................................................................................................................................................... 23Access Printer Preferences for Prin ng PDF Files........................................................................................................................................................... 23Set the Media Type, Media Size, Orienta on and Ribbon Type ............................................................................................................. 24Set the Print Quality, Color Matching and Image Adjustments .............................................................................................................. 24Set the Printable Area ............................................................................................................................................................................. 24Adjust the Print Alignment and Color Density ........................................................................................................................................ 25Check the Ribbon Remaining ................................................................................................................................................. 25
42001431_A Rimage Professional 3400 and 5400N User GuideChange the Print and Retransfer Ribbons .......................................................................................... 27Change the Print Ribbon ........................................................................................................................................................ 27Remove the Print Ribbon ........................................................................................................................................................................ 27Install the Print Ribbon ............................................................................................................................................................................ 29Change the Retransfer Ribbon ............................................................................................................................................... 30Remove the Retransfer Ribbon................................................................................................................................................................ 31Install the Retransfer Ribbon ................................................................................................................................................................... 32Maintain the 3400 and 5400N .......................................................................................................... 35Overview ...................................................................................................................... .......................................................... 35Cau onary Informa on ......................................................................................................................................................... 35Preventa ve Maintenance ..................................................................................................................................................... 35Preventa ve Maintenance Schedule ....................................................................................................................................................... 36Clean the Everest 400 Printer ................................................................................................................................................ 37Clean the Print Head ............................................................................................................................................................................... 37Clean the Tacky Rollers ............................................................................................................................................................................ 38Operate Gemini U li es ................................................................................................................... 41Start Gemini U li es .............................................................................................................................................................. 41Change the Autoloader Display Name ................................................................................................................................... 41Enable the Beeper ................................................................................................................................................................. 41
52001431_A Introduc onThis manual provides the informa on needed to confi gure, operate, and maintain the Rimage Professional™ 3400 and 5400N systems. The terms ‘system’ and ‘autoloader’ may be used throughout this manual to refer to both the 3400 and the 5400N; any diff erences between the 3400 and 5400N are noted. The term ‘printer’ is use to refer to the integrated Everest 400 printer. For technical informa on, refer to the Professional 3400 and 5400N Specifi ca ons sec on on page 10 of this manual or the Rimage Professional 3400 and 5400N Specifi ca on document found at www.rimage.com/support. From the Support menu select: Professional Series > Product Name > User Manuals tab. Note: Your Professional 3400 or 5400N system may not look exactly like the model featured in this user guide.About this User Guide• While we try to maintain all versions of our manuals and documenta ons, please note that the English version found on our web site always contains the most up-to-date informa on. • Unless otherwise indicated, all Windows naviga on statements are Windows XP paths. Other Windows opera ng system naviga on may diff er slightly.• These symbols are used throughout the manual to help clarify informa on: Note: A Note provides supplemental informa on or informa on that may apply only in special cases. For example, memory limita ons, equipment confi gura ons, or details that apply to specifi c versions of a program would be included in a Note. Tip: A Tip provides techniques and procedures to help with your specifi c needs. A Tip suggests alterna ve methods that may not be obvious and helps you understand the benefi ts and capabili es of the product. Important! An Important note provides informa on essen al to the comple on of a task. You can disregard informa on in a Note or Tip and s ll complete a task, but do not disregard an Important note. Cau on: A Cau on indicates that failure to observe this guideline could result in loss or damage to the equipment, product, so ware, or data. Warning! A Warning indicates that failure to follow this guideline could result in bodily injury to personnel opera ng or maintaining the equipment.About the Professional 3400 and 5400NThe 3400 and 5400N are part of the Rimage Professional series of products. The 3400 system consists of the 3400 autoloader and an integrated Everest 400 printer. The 5400N systems consists of the 5400N autoloader, an integrated Everest 400 printer, and an embedded control center (PC). Informa on about the integrated Everest 400 printer is included in this user guide.An external PC must be used with the non-embedded 3400 system. The external PC does not ship with a non-embedded system; you must provide a PC to be used as the external control center. Refer the Professional 3400 and 5400N Specifi ca ons sec on on page 10 for the minimum PC requirements for the 3400.The embedded PC in the 5400N is a network-ready device that receives orders from other networked computers. You can also operate the autoloader remotely by using Microso Remote Desktop Connec on or Rimage WebRSM or locally by a aching a monitor, keyboard, and mouse. For informa on about se ng up and submi ng orders from a networked PC, refer to the Rimage Advanced Setup (Networking) Guide available at www.rimage.com/support.
62001431_A Rimage Professional 3400 and 5400N User GuideAccessory KitThe Rimage Accessory Kit that shipped with your Professional 3400 or 5400N contains the following:3400 5400N• Rimage Professional 3400 Setup and Installa on Guide• User documenta on disc containing: Rimage Professional 3400 and 5400N User Guide (this document) Advanced Setup (Networking) Guide Diagnos c Test Instruc ons• A/C cord• USB cord• Disc holder with Rimage Standalone So ware disc or Network So ware Suite disc• Rimage Product Warranty/Guarantee• Ge ng Started with Your Rimage So ware guide• Marke ng CD• Rimage Professional 5400N Setup and Installa on Guide• User documenta on disc containing: Rimage Professional 3400 and 5400N User Guide (this document) Advanced Setup (Networking) Guide Diagnos c Test Instruc ons• A/C cord• DVI/USB dongle• Disc holder with Rimage Professional So ware Suite disc and Rimage Recovery Disc• Rimage Recovery Disc Instruc ons • Rimage Product Warranty/Guarantee• Ge ng Started with Your Rimage So ware guide• Marke ng CDUnpacking and Setup Instruc onsTo unpack your Professional 3400 or 5400N, refer to the unpacking label on the autoloader box. For setup instruc ons, refer to the Setup and Installa on Guide that shipped with your product.
72001431_A Important Informa onThis sec on provides support contact informa on, cau ons and warnings, and product specifi ca ons for the Professional 3400 and 5400N.Support Informa onUS, Asia/Pacifi c, Mexico/La n America EuropeRimage Corpora on7725 Washington Avenue SouthMinneapolis, MN 55439USAA n: Rimage ServicesRimage Europe GmbHAlbert-Einstein-Str. 2663128 Dietzenbach GermanyContact Rimage Services:Website: www.rimage.com/supportKnowledgeBase: h p://rimage.custhelp.com Log in and select the Ask a Ques on tabTelephone:North America: 800-553-8312Asia/Pacifi c, Mexico/La n America: 952-946-0004Fax: 952-946-6956Contact Rimage Services Europe:Website: www.rimage.deEmail: support@rimage.deTelephone: +49-(0) 1805-7462-43Fax: +49-(0) 6074-8521-101When you contact Rimage Services, please provide:• System serial number and so ware version• Func onal and technical descrip on of the problem• Exact error message receivedMy Rimage Product Informa on:Copy this informa on from your Rimage product for future reference. Note: Make sure you update the Serial Number here any me you receive a replacement system.Serial Number:Product Name:Date of Purchase:Learn More OnlineAt www.rimage.com/support, you can experience Rimage’s world-class Support and Services.From the Support home page:1. Select your product series.2. Select your product.3. Learn more on the product page.From your product page you can access:• Informa on about the latest so ware and fi rmwareupdates• Product specifi ca ons• The latest documents• Current fi rmware and driver downloadsTechnical SupportRimage off ers a variety of service and support op ons for the Professional 3400 and 5400N including Next Business Day On-site Agreements, Exchange Services, and So ware Subscrip ons and Support. Please contact your Rimage Value Added Reseller or Rimage for addi onal informa on and pricing. Important! Make sure that you register your autoloader so Rimage can no fy you of upgrades as they become available. Registra on is available at h p://www.rimage.com/support/warranty-registra on.
82001431_A Rimage Professional 3400 and 5400N User GuideOp cal Disc Recording So ware DisclaimerThis Product, So ware, or Documenta on may be designed to assist you in reproducing material in which you own the copyright or have obtained permission to copy from the copyright owner. Unless you own the copyright or have permission to copy from the copyright owner, you may be viola ng copyright law and be subject to payment of damages and other remedies. If you are uncertain about your rights, you should contact your legal advisor. If you are neither in possession of the copyright nor have authoriza on from the owner of the copyright, unauthorized copying of copyrighted material on an op cal disc or any other media violates na onal and interna onal legisla on and can result in severe penal es.Safety and Compliance Informa onThis manual and the indica ons on the product allow proper and safe opera on. The indica on marks below help protect you and other persons from injury, and equipment from damage. Safety Precau onsTo ensure safety, read these precau ons and familiarize yourself with their meaning before using the equipment. Warnings! • The laser beam used by the CD/DVD Recorder is a Class 1 laser. Do not a empt to open the recorder. An authorized technician should perform all service procedures.• Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radiant exposure.• Never use any op cal instrument in conjunc on with this unit. To do so will greatly increase the hazard to your eyes.• Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radiant exposure.• Do not disassemble or use tools on the printer. All service procedures should be performed by a Rimage-authorized technician, or sent in for Rimage-authorized repair.• The interior of the printer contains sharp edges.• Do not touch the heat roller.• Do not touch the circuit boards. The circuit boards can be damaged by electrosta c.• Do not remove the back panel unless the autoloader has been powered off .• Changes or modifi ca ons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.• This transmi er must not be co-located or operated in conjunc on with any other antenna or transmi er.• This equipment complies with FCC radia on exposure limits set forth for a controlled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evalua on (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremi es: hands, wrists, feet and ankles). Cau ons: • For con nued protec on against risk of fi re, replace the fuse only with the same type and ra ng. An authorized technician should perform all service procedures.• Use only the supplied AC power cord, or use a safety agency approved power cord. For applica ons outside North America, refer to the nearest Rimage offi ce for assistance in selec ng a locally approved power cord.• This product is designed for an offi ce environment.• The Professional 3400 and 5400N contain a lithium ba ery. There is a risk of explosion if the ba ery is replaced by an incorrect ba ery. Dispose of the old ba ery according to the manufacturer’s instruc ons included with the ba ery packaging.• All equipment with AC line voltage, or low DC voltages, such as switches, power supplies, fuses, fans, and non-stepper motors, must be replaced with Rimage-approved components to maintain the safety approval issued by UL.• Allow suffi cient free space for opening the printer tray. Do not touch the printer tray while it is in mo on.• If the side cover is opened while power is supplied, the printer will stop. Do not reach into the printer while it is in opera on. Do not a empt to bypass the door interlock.
92001431_A Country-specifi c Cau ons and Warnings for Wideband Data Transmission Systems: 2400-2483.5 MHz Cau ons:• France: Do not use outdoors.• Italy: If used outside of own premises, general authoriza on is required.• Norway: This subsec on does not apply for the geographical area within a radius of 20km from the center of NY-Alesund. Warning! • Canada: This equipment complies with IC radia on exposure limits set forth for a controlled equipment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evalua on (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremi es: hands, wrists, feet and ankles). Compliance Informa onProduct Professional 3400 Professional 5400NModel RAS26 RAS26ENo ce for USA NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference when this equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc on manual, may cause harmful interference to radio communica ons. Opera on of this equipment in a residen al area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.This product complies with UL 60950-1, 1st edi on.No ce for Canada This Class A digital apparatus complies with Canadian ICES-003 Issue 4:2004. Cet appareil numerigue de la classe A est conforme a la norme NMB-003 du Canade.This product complies with CAN/CSA-C22.2 No. 60950-1-03 1st edi on.No ce for Europe This product is in conformity with the EMC Direc ve (89/336/EEC) and the Low-Voltage Direc ve (73/23/EEC) through compliance with the following European standards: EN 55022: 1998 + Amd 1: 2000 Class B Limit; EN 55024: 1998; EN 61000-3-2:2000; EN 61000-3-3:1995 + Amd 1: 2001; EN 60950: 2000. The CE mark has been affi xed in accordance with the CE Marking Direc ve 93/68/EEC.No ce for Japan This is a Class A product based on the standard of the Voluntary Control Council for Interference by Informa on Technology Equipment (VCCI). If this equipment is used in a domes c environment, radio interference may occur, in which case, the user may be required to take correc ve ac on.Transla on:この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラスA 情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。No ce for Australia This product complies with AS/NZS CISPR22:2004.No ce for Korea It is cer fi ed that foregoing equipment has been cer fi cated under the Framework Act on Telecommunica ons and Radio Waves Act.위 기기는 전기통신기본법, 전파법 에 따라 인증되었음을 증명 합니다.
10 2001431_A Rimage Professional 3400 and 5400N User Guide3400 5400NStandard system Professional 3400 autoloader, integrated Everest 400 printer, and Rimage Standalone So ware Suite (RSS) or Network So ware Suite (NSS). Note: Non-embedded 3400 systems require an external control center (PC). External PCs are not shipped with Rimage non-embedded systems. Refer to the minimum PC requirements sec on below for more informa on.Professional 5400N autoloader, integrated Everest 400 printer, Rimage Producer So ware Suite (PSS), and an embedded control center (PC).Physical SizeHeight 18 in (46 cm) 18 in (46 cm)Width 14.25 in (36 cm) 14.25 in (36 cm)Depth 18.5 in (47 cm) 18.5 in (47 cm)Weight 64 lb (29 kg) 69 lb (31 kg)So warerequirements Rimage Standalone So ware Suite (RSS) or Network So ware Suite (NSS) 8.3 or higher.The required so ware is installed on the embedded PC.PC requirements Important! If you do not understand these requirements, ask your computer technician for help or refer to your PC documenta on. Note: The Professional 3400 and 5400N are not Macintosh compa ble.Supported opera ng systems(32-bit only)• Windows Vista Business SP2• Windows Vista Enterprise SP2• Windows Vista Ul mate SP2• Windows XP Professional SP3• Windows Server 2003 Standard SP2The supported opera ng system is installed on the 5400N embedded PC. Only the installed opera ng system is supported on this product.Minimum PC requirementsProcessor: Pen um 4, 2.8 GHz or fasterRAM/Memory: 1GBI/O: Use an integrated high-speed USB 2.0 port (using a USB expansion card is not recommended)Fixed Storage: Two 7,200 RPM hard drives with 10GB free space on each hard driveRemovable Storage: CD/DVD-ROMThe 5400N embedded PC is equipped with the minimum PC requirements.Specifi ca ons are con nued on page 11. Professional 3400 and 5400N Specifi ca onsThis sec on provides technical specifi ca on informa on for the non-embedded 3400 and the embedded 5400N system. Refer to page 12 for the Everest 400 printer specifi ca ons. Note: The most up-to-date technical specifi ca ons for the Professional 3400, 5400N, and integrated Everest 400 printer are located at www.rimage.com/support. From the Support menu select: Professional Series > Product Name > User Manuals tab.
112001431_A 3400 5400NMedia requirements Use Rimage Media Kits™ for op mum recording and print performance. Learn more about Media Kits at www.rimage.com.Networking ability To submit orders from a networked PC, refer to the Rimage Advanced Setup (Networking) Guide which shipped with your system and is available at www.rimage.com/support.Number of recorders 2Any combina on of CD, DVD, or Blu-ray Disc™ recorders.Bin capacityInput bin 50 discs per bin. The carousel has 3 input bins.Output bin The external output bin (on the le side of the autoloader) holds up to 8 discs. Note: Through the Rimage so ware, you can designate a bin in the carousel to be the output bin. In this case, the output bin holds up to 100 discs before operator interven on is required.Power100 – 240 VAC, 60/50 Hz, 4.7 – 3.7 Amp, 500 wa maximumTemperatureand HumidityOpera ngtemperature 60° to 86° F (16° to 30° C)Opera ngHumidity 40% to 80%, non condensingStoragetemperature 5° to 95° F (-15° to 35° C)
12 2001431_A Rimage Professional 3400 and 5400N User Guide Everest 400 Printer Specifi ca onsThe table below provides product specifi ca on informa on for the integrated Everest 400 printer. Important! If you do not understand these requirements, ask your computer technician for help or refer to your PC documenta on.Everest 400Prin ng speed* 60 seconds or lessPrin ng modes Monochrome and CMYPrint quality Equivalent of 400 pixels per inchRibbon capacityBlack (monochrome) 1000 discsCMY 500 discsRetransfer 500 discsRibbon requirements Refer to the Printer Requirements sec on on page 13 for the correct printer ribbons. Use Rimage Media Kits™ for op mum recording and print performance.Label design requirements Refer to the Label Design Requirements sec on on page 14 for label design requirements.Ribbon storage requirements **Temperature 41° to 95° F (5° to 35° C)Humidity 45% to 85%*The fi rst print takes 5 minutes, which includes warm-up  me.**For op mum results, make sure that the Everest ribbons are stored within these ranges.
132001431_A Printer RequirementsThis sec on describes ribbon, label design, and print requirements for the integrated Everest 400 printer.Ribbon Requirements Important!• Rimage only supports the use of Rimage brand ribbons in our printers. Printer issues that occur as a result of using ribbons from manufacturers other than Rimage are not included under your Rimage warranty or maintenance agreement.• For op mum results, make sure that Everest ribbons are stored at a temperature between 41° and 95°F (5° to 35°C) and humidity level between 45% and 85%. • Avoid moisture and direct sunlight.• Do not reuse ribbons.• Use only ribbons designed for your Everest 400 printer. Refer to the table below.The integrated Everest 400 printer requires a print ribbon and a retransfer ribbon. The standard print ribbon has three colors: Cyan, Magenta, and Yellow (CMY). These three colors combine in prin ng to create full-color discs. Print ribbons are also available in black (monochrome). Everest 400 RibbonsRibbon Type Number of Discs Printed3-color (CMY) 500Black (monochrome) 1000Retransfer ribbon 500
14 2001431_A Rimage Professional 3400 and 5400N User Guide Label Design RequirementsThe Rimage Windows-compa ble so ware ships with the CD Designer™ label editor. CD Designer is installed on the embedded or non-embedded PC during a typical installa on of the Rimage so ware and is used for designing labels for prin ng with the integrated Everest 400 printer. CD Designer can be used to design labels on any Windows-based PC.• Label design size – Design labels with a height of 12 cm and width of 12 cm. A full-size disc is 120 mm (4.723") in diameter. The hole is 15 mm (0.59”) The printable area and hub sizes vary depending on the disc manufacturer. Note: The media that are in Rimage Media Kits have a printable area of 118-24 mm. On most labels, print se ngs of 118 mm and 24 mm are recommended.• File format – For best results, save your labels as JPEG or TIFF fi les. However, these fi le formats must be imported into CD Designer and saved as CD Designer fi les (.btw) or converted to PDF fi les before prin ng.• Color mode – Convert all labels to the RGB color mode in order to import them into CD Designer. • Resolu on (pixels per inch) – For best results, use images set to a minimum of 300 pixels per inch. You may no ce be er results if you use images with 600 pixels per inch or higher.Print RequirementsAny label you create and save through CD Designer is in the correct fi le format (.btw) for prin ng to the integrated Everest 400 in the 3400 and 5400N system. You can also print labels saved as PDF fi les.PrintableArea 118 mmHub Size24 mm
152001431_A Iden fy the Parts of the Professional 3400 and 5400NThis sec on describes the hardware and features of the 3400 and 5400N systems. Front ViewControl PanelPC Power Bu on(5400N Only)Front DoorCarousel/Input BinsOutput BinRecordersPrinter DoorLi ArmDisc DispenserOperator PanelIntegrated Everest 400 Printer
16 2001431_A Rimage Professional 3400 and 5400N User GuideBack View34005400NPower CordNetwork CablePower SwitchPower Cord USB CablePower Switch
172001431_A Parts Informa onControl PanelThe control panel is located on the front of the 3400 and 5400N. It includes the operator panel, the rotate carousel bu on (bu on 1), and the printer tray bu on (bu on 2). The control panel allows you to monitor and control the system.Note: You must open the front door of the autoloader to access the control panel.The table below iden fi es the name and func on of all parts of the control panel.Control Panel Indicators Name Func onOperator panel The operator panel has a two-line display that informs you of opera ons or condi ons that require operator interven on. This includes the consumable status. The 5400N displays the name of the embedded PC a er ini aliza on. Refer to the Operator Gemini U li es sec on on page 41 to see other op ons.Rotate carousel bu on (bu on 1)Press the rotate carousel bu on to • Rotate the carousel and posi on a bin to load and unload discs. Each  me you press the rotate carousel bu on, the carousel rotates to the next bin. Tip: The carousel will rotate to a bin only a er the autoloader has completed ini alizing.• Enter diagnos c test mode Printer tray bu on (bu on 2)Press the printer tray bu on to:• Open and close the printer tray• Reset a er an errorPrinter indicator light (on the printer tray bu on)The printer indicator light illuminates when the printer is powered on and has completed ini aliza on.The printer indicator light fl ashes when the Everest 400 printer is receiving data from the host.Rotate carousel indicator light (on the rotate carousel bu on)The rotate carousel indicator light illuminates when you rotate the carousel.The rotate carousel indicator light fl ashes when the autoloader is receiving data from the host.PC Power Bu onOnly the 5400N has the PC power bu on. The PC power bu on powers on the embedded computer. Refer to the Operate the Professional 3400 and 5400N sec on on page 19 for more informa on.Disc DispenserWhen a disc is complete, the li arm places discs on the disc dispenser. The disc dispenser moves completed discs to the output bin on the le side of the autoloader. The output bin holds up to 5 discs. Refer to the Professional 3400 and 5400N Specifi ca ons sec on on page 10 for more informa on.OperatorPanelRotateCarouselBu onPrinter Tray Bu on
18 2001431_A Rimage Professional 3400 and 5400N User Guide
192001431_A Operate the Professional 3400 and 5400N SystemThis sec on provides the informa on needed to operate your system. Power On the System1. Press the power switch on the rear of the autoloader. The system powers on, including the integrated printer.If you have an 5400N, con nue with step 2.2. On the front of the 5400N, press the PC power bu on to power on the embedded PC.Power Off the System1. Close all open applica ons.2. If you have an 5400N briefl y press the PC power bu on. This shuts down the so ware, Windows, and the embedded PC.If you have a 3400, con nue with step 3. Cau on: Do not press and hold the PC power bu on. If you press and hold the PC power bu on, the embedded PC will not shut down properly. This may cause data loss or corrup on.3. Press the main power switch to power off the system, including the integrated printer. Important! Do not press the power switch un l the embedded PC is completely powered off . Notes: • It takes approximately 30 seconds for the system to power off .• If the printer is idle for more than 30 minutes, it enters sleep mode. When this occurs, the printer will take 2-3 minutes to warm up a er a job is sent.Power SwitchPC Power Bu on(5400N Only)
20 2001431_A Rimage Professional 3400 and 5400N User GuidePause the SystemYou can pause the system to add discs to the carousel.1. Open the front door. The opera on pauses.2. Close the front door. The opera on resumes.Load the DiscsYou can load up to 50 discs in each input bin. Use the procedure below to load discs in each bin.1. Open the front door.2. Press the rotate carousel bu on to rotate the carousel and place a bin in posi on to load discs. 3. Remove any completed discs from the bin. Important! Place the discs with the recording side facing down. Tip: Through the Rimage so ware, you may designate bins 1 through 3 as input, output, reject, or a specifi c media type.4. Repeat steps 2 - 3 un l the required bins are fi lled.5. Close the front door.Unload the Discs1. Open the front door.2. Press the rotate carousel bu on to rotate the carousel and place a bin in posi on to remove discs.3. Remove the discs from the bin.4. Repeat steps 2 - 3 un l the required bins are empty.5. Close the front door.
212001431_A Place a Disc on the Printer TrayUse this procedure to manually place a disc on the printer tray.1. Press the printer tray bu on on the control panel. The printer tray opens.2. Place the disc on the print pad with the printable surface facing up and the stacking ring facing the print pad.3. Press the printer tray bu on. The printer tray closes. Important! To avoid scratching or damaging the recording surface of the disc, the disc must not rest on the holding pins or the centering pin.Place a Disc on the Recorder TrayUse this procedure to manually place a disc on the recorder tray.1. Press the recorder bu on on the recorder you wish to open. The recorder tray opens.2. Place the disc on the recorder tray with the printable surface facing up.3. Press the recorder bu on. The recorder tray closes.Holding Pins
22 2001431_A Rimage Professional 3400 and 5400N User Guide
232001431_A Set Your Prin ng Preferences on a Windows PCThis sec on provides the informa on needed to set up your prin ng preferences and check the amount of print and retransfer ribbon remaining using a Windows PC. Prin ng preferences allow you to set up the integrated Everest 400 printer to produce the best possible labels on your discs. Note: Unless otherwise indicated, all Windows naviga on statements are Windows XP paths. Other Windows opera ng system naviga on may diff er slightly. Access Prin ng Preferences Use one of the procedures below to access the Everest 400 Prin ng Preferences window.Access Prin ng Preferences through the Windows Start Menu Note: When you use this method, the prin ng preferences are saved in the printer driver se ngs and are applied to all newly created labels.1. Select: Start > Printers and Faxes.2. Right-click the Rimage Everest 400 printer. The dropdown menu displays.3. From the dropdown menu, select Prin ng Preferences. The Rimage Everest 400 Prin ng Preferences dialog box opens.Access Printer Preferences through CD Designer Note: When you use this method, the prin ng preferences are saved with the label fi le and are used instead of the printer driver se ngs.1. Open the desired label fi le in CD Designer.2. From the File menu, select Print. The Print window opens.3. From the Name dropdown list, select the Rimage Everest 400 printer. Note: The Rimage Everest 400 printer may display as the default printer.4. Select the Document Proper es bu on. The Rimage Everest 400 Proper es dialog box opens.Access Printer Preferences for Prin ng PDF FilesUse the procedure below to access prin ng preferences for PDF fi les. Important! When you use this procedure, the changes to the se ngs are global and apply to all PDF labels.1. Select: Start > Printers and Faxes.2. Right-click on the Everest 400 printer. The dropdown menu displays.3. From the dropdown menu, select Proper es. The Rimage Everest 400 Proper es dialog box opens.4. From the Rimage Everest 400 Proper es dialog box, select the Advanced tab.5. At the bo om of the Advanced tab, select Prin ng Defaults… The Rimage Everest 400 Prin ng Defaults dialog box opens.
24 2001431_A Rimage Professional 3400 and 5400N User GuideSet the Media Type, Media Size, Orienta on and Ribbon Type 1. Access prin ng preferences. Refer to page 23 for instruc ons.2. Select the Main tab.3. View or change the prin ng preferences.a. Select the appropriate Media Type.b. Select the appropriate Media Size.c. Select the desired number of Copies.d. Select the desired Orienta on.e. Select the appropriate type of Ribbon. Note: If you select Monochrome for the ribbon type, select Grayscale or Text.4. When you have made the desired choices in the Rimage Everest 400 Prin ng Preferences window, select Apply. 5. Select OK to close the Rimage Everest 400 Prin ng Preferences window.Set the Print Quality, Color Matching and Image Adjustments 1. Access prin ng preferences. Refer to page 23 for instruc ons.2. Select the Advanced tab.3. View or change the prin ng preferences.a. Select the desired criteria for Color Matching. Note: The default se ng for color matching is Match for CMYK prin ng.b. From the Image Adjustments dropdown list, select None, High contrast, Vivid colors, or Custom. If you select Custom, the Se ngs bu on becomes ac ve:i. Select the Se ngs bu on. The Custom Se ngs window opens. ii. Select the desired Print Threshold Se ngs.iii. Move the Contrast Boost slider to adjust the image contrast.iv. Move the Satura on Boost slider to adjust the image satura on.v. Select OK to close the Custom Se ngs window.4. When you have made the desired choices in the Rimage Everest 400 Prin ng Preferences window, select Apply.5. Select OK to close the Rimage Everest 400 Prin ng Preferences window.Set the Printable Area This func onality allows you to adjust the printable area se ngs for standard CD/DVD 120 mm media, which sets the outer and inner diameters to print the disc label without overlapping the disc edges. Note: Printable area se ngs created within a CD Designer label fi le will override the printer and fax se ngs on Windows.1. Access prin ng preferences. Refer to page 23 for instruc ons.2. Select the Advanced tab.3. View or change the Printable Area preferences.a. Select the Modify bu on. The Printable Area Se ngs window opens.b. Select the Unit of measurement.i. For 1.0 mm, select the 1.0 mm radio bu on.ii. For 0.1 mm, select the 0.1 mm radio bu on.
252001431_A c. To modify only Standard Area se ngs, select the Standard radio bu on.i. Enter the desired Outer Diameter.ii. Enter the desired Inner Diameter.d. To print on a disc with a stacking ring, select the Advanced radio bu on. The Hub Area se ngs display.i. Enter the desired Outer Diameter for the hub.ii. Enter the desired Inner Diameter for the hub.e. Select OK to save the changes. The Printable Area Se ngs window closes.4. When you have made the desired choices in the Rimage Everest 400 Prin ng Preferences window, select Apply.5. Select OK to close the Rimage Everest 400 Prin ng Preferences window. Adjust the Print Alignment and Color Density. Adjust the Print Alignment and Color Density 1. Access prin ng preferences. Refer to page 23 for instruc ons.2. Select the U lity tab.3. Select Status Monitor… bu on. The Rimage Everest 400 Status Monitor window opens with the Status tab ac ve. Tip: On the Status tab, you can view the progress of a print job, the type of print ribbon installed, and the es mated percentages of unused ribbon for the print and retransfer ribbons.4. Select the Printer Informa on tab to view or change the Print Alignment and Color Density se ngs, or view the Everest 400 Printer Status. Tip: The Printer Informa on tab also displays the current fi rmware version and serial number of your Everest 400 printer.a. View or change the Print Alignment Se ngs.i. From the Print Alignment Se ngs pane, select the Modify bu on. The Print Alignment Se ngs dialog opens.ii. Select the desired Color/Monochrome se ng to modify the horizontal alignment for all ribbon types.iii. Select the desired Color se ng to modify the ver cal alignment for prints with a CMY ribbon.iv. Select the desired Monochrome se ng to modify the ver cal alignment for prints with a monochrome ribbon.v. Select OK to save the changes. The Print Alignment Se ngs window closes.b. View or change the Color Density Se ngs.i. From the Color Density Se ngs pane, select the Modify bu on. The Color Density Se ngs dialog opens.ii. Select the desired Cyan, Magenta and Yellow se ngs to modify the color density.iii. Select the desired Black se ng to modify the density for monochrome images.iv. Select OK to save your changes. The Color Density Se ngs window closes.5. Select Close to close the Status Monitor dialog box.6. Select OK to close the Rimage Everest 400 Prin ng Preferences window.Check the Ribbon RemainingThe operator panel on the front of the 3400 and 5400N displays the es mated number of prints remaining on the print ribbon and the retransfer ribbon.
26 2001431_A Rimage Professional 3400 and 5400N User Guide
272001431_A Change the Print and Retransfer RibbonsThis sec on provides the informa on needed to change the print and retransfer ribbons in the integrated Everest 400 printer. Change a 3-color (CMY) print ribbon a er 500 discs, a back (monochrome) print ribbon a er 1000 discs, and the retransfer ribbon a er 500 discs.Change the Print RibbonBefore you change or fi rst install a new Everest print ribbon, allow  me for the new ribbon to become acclimated to the environment. Allow more  me for greater temperature and humidity diff erences. Important!• Rimage supports only the use of Rimage brand ribbons in our printers. Printer issues that occur as a result of using ribbons from manufacturers other than Rimage are not included under your Rimage warranty or maintenance agreement.• For op mum results, make sure that Everest ribbons are stored at a temperature between 41° and 95°F (5° to 35°C) and humidity level between 45% and 85%. • Avoid moisture and direct sunlight.• Do not reuse ribbons.• Use only ribbons designed for your model of Everest 400 printer.• The ribbon carriers cannot be removed from the printer unless the system is powered on.Remove the Print Ribbon1. Open the side cover on the le side of the autoloader.a. Li the printer cover latch to open the printer cover.b. Lower the printer cover.2. Access the print ribbon.a. Turn the center latch counterclockwise to unlock it.b. Pull the print ribbon carrier all the way out of the printer. Important! The ribbon carriers cannot be removed from the printer unless the system is powered on.Printer CoverPrinter Cover LatchLe Side of AutoloaderCenter Latch Print Ribbon Carrier
28 2001431_A Rimage Professional 3400 and 5400N User Guidec. Lay the print ribbon carrier on its back. Tip: Perform cleaning procedures while the print ribbon is removed. For more informa on refer to the Clean the Everest 400 Printer sec on on page 37. d. Place the print ribbon carrier on a fl at surface. Tip: To keep the print ribbon carrier in place while you remove the print ribbon, posi on the carrier so that the tab rests on the edge of a table or workspace. 3. Remove the used print ribbon from the carrier.a. Li up on the supply roll to remove it from the right side of the carrierb. Set the supply roll aside.c. Li up on the take-up roll to remove it from the le side of the carrier.d. Set the take-up roll aside.e. Li the print ribbon carrier off of the print ribbon and set it aside.f. Discard the used print ribbon.TabPrint RibbonCarrierUsed Supply RollUsed Take-Up Roll
292001431_A Install the Print Ribbon1. Remove the new print ribbon from the packaging.2. Install the print ribbon on the print ribbon carrier. Important! When you install the new print ribbon on the carrier, do not rotate the ribbon past the black cleaning bars. When the new ribbon is installed in the integrated Everest 400 printer, the ribbon advances and the bars clean the print head.a. With the supply roll on the right side, unwind several inches of the new print ribbon.b. Place the print ribbon on a clean, fl at surface.c. Place the print ribbon carrier on top of the print ribbon. Tip: To keep the print ribbon carrier in place while you install the print ribbon, posi on the carrier so that the tab rests on the edge of a table or workspace.d. Bring the supply roll up and around the tacky roller and guide rollers on the right side of the carrier.e. Press down to install the supply roll, as shown.f. Bring the take-up roll up and around the guide roller on the le side of the carrierg. Press down to install the take-up roll, as shown.TabNew Take-Up Roll New Supply RollSupply RollGuide RollerTacky RollerGuide RollerTake-UpRoll
30 2001431_A Rimage Professional 3400 and 5400N User Guideh. Set the print ribbon carrier upright. Tip: When the print ribbon carrier is upright, the supply roll is at the top of the carrier.i. Rotate the take-up roll clockwise to  ghten the ribbon. Make sure that the ribbon is aligned and lies fl at on the carrier. Tip: You may need to li the ribbon up from the tacky roller to straighten it. Notes: • Do not rotate the ribbon past the black cleaning bars at the front of the ribbon.• If you installed a black (monochrome) ribbon, advance the ribbon so the ink por on of the ribbon is advanced to the take-up roll.3. Reassemble the printer.a. Slide the print ribbon carrier into the printer.b. Turn the center latch clockwise to lock it.c. Close the printer cover. Note: Ribbon color can vary from lot to lot. A er you load the new ribbon, you may need to adjust the density se ngs in the printer driver. Refer to the Adjust the Print Alignment and Color Density sec on on page 25 for more informa on.The printer is ready for use. Change the Retransfer RibbonBefore you change or fi rst install the Everest retransfer ribbon, allow  me for the new ribbon to become acclimated to the environment. Allow more  me for greater temperature and humidity diff erences. Important!• Rimage supports only the use of Rimage brand ribbons in our printers. Printer issues that occur as a result of using ribbons by manufacturers other than Rimage are not included under your Rimage warranty or maintenance agreement.• For op mum results, make sure that Everest ribbons are stored at a temperature between 41° and 95°F (5° to 35°C) and humidity level between 45% and 85%.• Avoid moisture and direct sunlight.• Do not reuse ribbons. • Make sure you only use ribbons designed for your model of Everest 400 printer. • The ribbon carriers cannot be removed from the printer unless the system is powered on.Supply Roll
312001431_A Remove the Retransfer Ribbon1. Open the printer cover.a. Li the cover latch to release the cover.b. Lower the printer cover.c. Turn the center latch counterclockwise to unlock it.d. Pull the retransfer ribbon carrier all the way out of the printer. Important! The ribbon carriers cannot be removed from the printer unless the system is powered on.e. Lay the retransfer ribbon carrier on a fl at surface.2. Remove the used retransfer ribbon.a. Li up on the take-up roll to remove it from the right side of the carrier.b. Set the take-up roll aside.Printer CoverLatchPrinter CoverLe Side of AutoloaderCenter LatchRetransfer Ribbon CarrierUsed Take-Up Roll
32 2001431_A Rimage Professional 3400 and 5400N User Guidec. Li up on the supply roll to remove it from the le side of the carrier.d. Set the supply roll aside.e. Li the retransfer ribbon carrier off of the used retransfer ribbon and set it aside.f. Discard the used retransfer ribbon. Install the Retransfer Ribbon1. Remove the new retransfer ribbon from the packaging.2. Posi on the retransfer ribbon on the retransfer ribbon carrier.a. With the supply roll on the le side, unwind several inches of the retransfer ribbon.b. Place the retransfer ribbon on a clean, fl at surface.c. Place the retransfer ribbon carrier on top of the retransfer ribbon.3. Install the retransfer ribbon.a. Bring the take-up roll up and around the guide roller on the right side of the carrier.b. Press down to install the take-up roll, as shown.Used Supply RollNew Take-Up RollNew Supply RollRetransfer Ribbon CarrierTake-Up RollGuide Roller
332001431_A c. Bring the supply roll up and around the guide rollers on the le side of the carrier. d. Press down to install the supply roll, as shown. Note: Make sure that the retransfer ribbon winds underneath the supply roll.4. Rotate the take-up roll counterclockwise to  ghten the retransfer ribbon. 5. Reassemble the printer.a. Slide the retransfer ribbon carrier into the printer.b. Turn the center latch clockwise to lock it. c. Close the printer cover.The printer is ready for use.Guide RollersSupply RollTake-Up Roll
34 2001431_A Rimage Professional 3400 and 5400N User Guide
352001431_A Maintain the 3400 and 5400NThis sec on provides maintenance informa on for the 3400 and 5400N systems, including the integrated Everest 400 printer. Important! For op mum performance, keep the 3400 and 5400N in a clean, dust-free environment.OverviewRegular preventa ve maintenance of your system can help to ensure error-free recordings and clean printed labels. Maintenance also involves cleaning the system.Cau onary Informa on Cau on: To avoid damaging the 3400 or 5400N during maintenance:• Never use oils, silicone, or other lubricants on any part of the system.• Use only non-abrasive cleaners to wipe down the surfaces of your autoloader..• Never use cleaners to clean the embedded PC.• Avoid pouring cleaners directly onto the autoloader. Instead, apply the cleaner a clean, lint-free cloth.• Observe precau ons for electrosta c-sensi ve devices whenever you access the embedded PC.Preventa ve MaintenanceYou must perform rou ne maintenance to keep the system opera ng at op mum performance. The Preventa ve Maintenance Schedule on page 36 lists maintenance tasks, task frequency, and references to cleaning instruc ons in this user guide. Important! Failure to follow the maintenance schedule may void your warranty. Note: Your system may require more frequent maintenance if used in a dusty area, such as a store or warehouse.Before you begin:1. Power off the autoloader.2. If you have a 5400N, power off the embedded PC.3. Disconnect the power cord.4. Follow the Preventa ve Maintenance Schedule on page 36.
36 2001431_A Rimage Professional 3400 and 5400N User GuidePreventa ve Maintenance ScheduleTask Tools FrequencyAutoloader MaintenanceWipe down the li arm sha and pay close a en on to:• The area around the base of the sha • The area just above the li armLint-free cloth Weekly Wipe down all surfaces of the autoloader, including: • Lint-free cloth• Non-abrasive, all-purpose cleanerWeekly• Sides and top• Door• Output bin• Carousel• Top surface on the li armRemove dust and debris from the fan at the back of the autoloader.Can of compressed air MonthlyRemove dust and debris from the openings at the back of the autoloader.Vacuum MonthlyRemove dust and debris from the front and inside of the autoloader. Can of compressed air MonthlyIntegrated Everest 400 Printer MaintenanceClean the print head. Refer to the Clean the Print Head sec on on page 37.• Sponge swabs with long handles (included in the Everest cleaning kit)• 99% Isopropyl alcoholA er 2000 discs (as needed) or at every ribbon changeClean the tacky rollers. Refer to the Clean the Tacky Rollers sec on on page 38.• Sponge swabs with long handles (included in the Everest cleaning kit)• 99% Isopropyl alcoholA er 2000 discs or at every ribbon change
372001431_A Clean the Everest 400 PrinterRegular cleaning helps to keep your Everest 400 printer in op mal opera ng condi on.Clean the Print Head Tools required:• Sponge swabs with long handles (included in the Everest cleaning kit)• 99% Isopropyl alcohol1. Access the print head.a. Li the printer cover latch to open the cover.b. Lower the printer cover.c. Turn the center latch counterclockwise to unlock it.d. Remove the print ribbon carrier. Important! The ribbon carriers cannot be removed from the printer unless the system is powered on.2. Clean the print head. Cau on! Do not scratch the print head. Remember the following  ps:• Always wipe from one end of the print head to the other without stopping in the middle.• Only wipe the area indicated.a. Apply isopropyl alcohol to the sponge swab.b. Use the sponge swab to wipe across the print head from one end to the other in the direc on shown below. Note: Do not remove the print head component from the inside of the printer. The component is shown outside of the printer for instruc onal purposes only.c. Repeat as needed un l the print head is clean of dust and debris.d. Use the sponge swab to remove any waxy buildup from the roller below the print head. Center LatchPrint Ribbon CarrierPrint Head Area to CleanRollerWipe Direc on
38 2001431_A Rimage Professional 3400 and 5400N User Guide3. Prepare the printer for use.a. Install the print ribbon carrier.b. Turn the center latch clockwise to lock it.c. Close the printer cover. The system is ready for use. Clean the Tacky Rollers Tools required:• Sponge swabs with long handles (included in the Everest cleaning kit)• 99% Isopropyl alcohol1. Remove the print ribbon carrier.a. Li the printer cover latch to open the cover.b. Lower the printer cover.c. Turn the center latch counterclockwise to unlock it.d. Remove the print ribbon carrier. Important! The ribbon carriers cannot be removed from the printer unless the system is powered on.2. Remove the print ribbon. For specifi c instruc ons, refer to the Change the Print Ribbon procedure on page 27.3. Clean tacky roller 1 on the print ribbon carrier.a. Apply isopropyl alcohol to the sponge swab.b. Use the sponge swab to clean tacky roller 1. c. Use the sponge swab to remove any waxy buildup from other parts of the print ribbon carrier.Center Latch Print Ribbon CarrierPrint Ribbon CarrierTacky Roller 1
392001431_A 4. Inside the printer, use the sponge swab to wipe tacky roller 2.5. Prepare the printer for use.a. Install the print ribbon on the print ribbon carrier. For specifi c instruc ons, refer to the Change the Print Ribbon procedure on page 27.b. Install the print ribbon carrier in the printer.c. Turn the center latch clockwise to lock it.d. Close the printer cover.The system is ready for use.Tacky Roller 2
40 2001431_A Rimage Professional 3400 and 5400N User Guide
412001431_A O perate Gemini U li esThe Rimage so ware includes an applica on called Gemini U li es, which is used to change the display name of the system and to enable the beeper. Gemini U li es is only available on the Professional 5400N and the Professional 3400 running Rimage Network So ware Suite. Tip: To access Gemini U li es for the 5400N, use the remote desktop connec on from a networked PC, or connect a monitor, keyboard, and mouse to the 5400N. Note: Unless otherwise indicated, all Windows naviga on statements are Windows XP paths. Other Windows opera ng system naviga on may diff er slightly.Start Gemini U li es1. Close all open so ware applica ons and stop all Rimage Services. Note: Refer to your Rimage so ware online help for addi onal informa on.2. From the Windows Start menu select: All Programs > Rimage > U li es > Gemini U li es. Gemini U li es opens. Note: When the desired tasks are complete, start the Rimage Services.Change the Autoloader Display NameUse Gemini U li es to enter the name displayed on the operator panel. Note: Changing the display name does not change the name of the system on a network or workgroup. To change the name on a network or workgroup, refer to your setup and installa on instruc ons or the Rimage Advance Setup (Networking) Guide.1. Select the Override Name checkbox.2. Clear the Use Computer Name checkbox.3. In the Display Name fi eld, enter the new name.4. Select Set Params to set the name. Enable the BeeperYou can change the number of beeps that occur when the unit is out of media or when there is an error.1. In the # of Beeps on Fault fi eld, select the number of beeps you wish to hear when there is an error. Tip: To disable the beeper, set the number to zero. 2. Select Set Params to set the number of beeps.

Navigation menu