Rimage 360I Users Manual User Guide (English)

360i to the manual 4244c115-a4c7-412d-ad3e-6dc338f2fd8c

2015-02-06

: Rimage Rimage-360I-Users-Manual-524061 rimage-360i-users-manual-524061 rimage pdf

Open the PDF directly: View PDF PDF.
Page Count: 27

Rimage 360i™
User Guide
This manual provides the information needed to operate the Rimage 360i and identify the parts.
To set up and install your Rimage 360i, refer to the Rimage 360i Setup and Installation Guide.
Corporate Headquarters:
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
European Headquarters:
Rimage Europe GmbH
Hans-Böckler-Straße 7
63128 Dietzenbach, Germany
CD and DVD Recording Software
Disclaimer
This Product, Software, or Documentation may be
designed to assist you in reproducing material in
which you own the copyright or have obtained
permission to copy from the copyright owner.
Unless you own the copyright or have permission
to copy from the copyright owner, you may be
violating copyright law and be subject to payment
of damages and other remedies. If you are
uncertain about your rights, you should contact
your legal advisor. If you are neither in possession
of the copyright nor have authorization from the
owner of the copyright, unauthorized copying of
CDs violates national and international legislation
and can result in severe penalties.
Rimage Corporation reserves the right to make
improvements to the equipment and software
described in this document at any time without any
prior notice. Rimage Corporation reserves the right to
revise this publication and to make changes from
time to time in the content hereof without obligation of
Rimage Corporation to notify any person or
organization of such revisions or changes.
This document may contain links to web sites that
were current at the time of publication, but may have
moved or become inactive since. This document may
contain links to sites on the Internet that are owned
and operated by third parties. Rimage Corporation is
not responsible for the content of any such third-party
site.
©2005, Rimage Corporation
Rimage™ is a trademark of the Rimage Corporation.
360i™ is a trademark of the Rimage Corporation.
Dell® is registered trademark of Dell Computer
Corporation. FireWire® is a registered trademark of
Apple Computer, Inc.
All other trademarks and registered trademarks are
the property of their respective owners.
Rimage 360i
Support information
For Rimage 360i™ Support, go to:
www.rimage.com/Rimage360iSupport
North America
South America
Asia/Pacific
Europe
Africa
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
Rimage Europe GmbH
Hans-Böckler-Straße 7
63128 Dietzenbach, Germany
Contents
Contents
Introduction .....................................................................................................................1
Requirements..............................................................................................................1
Software requirements ..........................................................................................1
Operating System requirements............................................................................1
Media requirements...............................................................................................1
Ink requirements....................................................................................................1
Label design requirements....................................................................................2
Identify the parts of the Rimage 360i ............................................................................3
Front View .............................................................................................................3
Rear view ..............................................................................................................6
Operate the Rimage 360i ................................................................................................7
Powering on the Rimage 360i ...............................................................................7
Pausing the Rimage 360i ......................................................................................7
Loading the discs ..................................................................................................8
Select your printing preferences .................................................................................9
Navigating to Printing Preferences........................................................................9
Setting the print quality........................................................................................10
Adding, editing, or deleting a watermark.............................................................10
Adjusting the ink volume used.............................................................................11
Setting up color options.......................................................................................11
Changing or enabling masking............................................................................12
Printing on hub with a stacking ring.....................................................................12
Printing on hub without a stacking ring................................................................13
Aligning the ink cartridges ...................................................................................13
Centering the image on the disc..........................................................................14
Checking the ink levels........................................................................................14
Maintain the Rimage 360i .............................................................................................15
General Cleaning ......................................................................................................15
Cleaning the exterior ...........................................................................................15
Cleaning the ink cartridge nozzles ......................................................................15
Replace Consumables..............................................................................................16
Replacing the fan filter.........................................................................................16
Replacing the ink cartridges................................................................................17
Learn More.....................................................................................................................18
Rimage 360i Specifications.................................................................................18
Technical support and product updates ..............................................................19
Safety information ...............................................................................................19
Safety testing.......................................................................................................20
Rimage 360i Limited 1 Year Warranty ................................................................21
110808_C i
Rimage 360i
ii
Introduction
Introduction
This manual provides the information needed to operate the Rimage 360i and identify the parts.
To set up and install your Rimage 360i, refer to the Rimage 360i Setup and Installation Guide.
Requirements
Software requirements
The Rimage 360i will operate only with the Rimage 360i Software.
Operating System requirements
The Rimage 360i and software run only on Windows 2000, and Windows XP, and Windows 2003.
Media requirements
You must use discs that are coated with a surface that is designed for inkjet printing. The media
that is in Rimage Media Kits™ is designed for optimum use in the Rimage 360i.
Ink requirements
The following cartridge combinations are supported. The printer will work only with
the following printer cartridges.
Description Rimage Part #
Black RB1
Color RC1
Photo RP1
Left Position Right Position
Color Black
Color Photo
Color No cartridge
No cartridge Black
n Warning:
Ink may be harmful if swallowed.
Avoid contact with eyes.
Ink contains nitrites. If ingested, seek immediate medical attention.
Keep out of reach of children.
Refilling ink cartridges may result in damage to the cartridge or printer.
Rimage ink cartridges are not licensed for modification.
- Important! You can use only Rimage ink cartridges in the Rimage 360i.
110808_C 1
Rimage 360i
2 110808_C
Label design requirements
The Rimage 360i Software includes a label editor called CD Designer™, which is installed on
your system. You can use CD Designer to design your labels.
If you have another software application that you prefer, you can create a label and save it as an
Acrobat®(.pdf) file, a .jpg file, or a .tiff file.
- Important! Only the Acrobat (.pdf) file can print directly to the Rimage 360i. To create a label
with another software application, use the following criteria:
• Color Depth – Save the artwork for the label with the color set to at least 256 colors. A color
setting higher than 256 colors is recommended.
• DPI – Use pictures or logos set to 300 DPI (dots per inch).
• Label Design Size – A standard disc is 120mm (4.723”). The hole is 15mm (0.59”). The
printable area and hub sizes vary depending on the disc manufacturer.
• Media – The media that is in Rimage Media Kits™ has a hub area of 23 mm and a printable
area of 118 mm. On most labels, print settings of 24 mm and 118 mm are recommended.
Identify the parts of the Rimage 360i
Identify the parts of the Rimage 360i
This section describes the Rimage 360i hardware and its features.
Front View
Front
Cove
r
Input
Door
Project Status
Indicator (PSI)
Ink Cartridge
Access Door
Disc
Output
110808_C 3
Rimage 360i
4 110808_C
Rimage 360i Buttons
On the right side of the Rimage 360i, there is one button.
Pause button
• Press this button once to pause the Rimage 360i.
• Press this button again to return to normal operation.
Inside the front cover of the 360i, there are three buttons.
To access these buttons, open the front cover.
n Warning: Touch only the buttons indicated below.
Touching the inner parts of the 360i may cause equipment
failure or injury and may void your warranty.
Red (top)
Press this button to power the 360i printer on and off.
Green (middle)
Press this button to move the 360i printer tray in and out.
Black (bottom)
Press this button to cancel printing.
Identify the parts of the Rimage 360i
Rimage 360i Project Status Indicator (PSI)
On the front of the Rimage 360i is the Project Status
Indicator (PSI), made up of 5 LEDs.
LED: Light-emitting diode. A type of diode that emits
light when current passes through it.
The PSI communicates Rimage 360i, disc, printer,
and recorder status. Some of the functions
communicated include:
• Power
• Disc moving
• Disc in recorder
• Disc printing
• Ink status
Image Name Functionality
Power • The power LED is green when the Rimage 360i is powered on.
• The power LED is amber when the Rimage 360i is paused.
Disc in
motion
• The disc in motion LED is solid green when the disc is still.
• The disc in motion LED blinks green when the disc is in motion.
• The disc in motion LED blinks amber when the Rimage 360i is out
of blank discs.
Disc in
recorder
• The disc in recorder LED is green when the disc is in the recorder.
• The LED is dim when there is no disc in the recorder.
• The LED is amber when the recorder state is unknown.
Disc
printing
• The disc printing LED blinks green when the printer is printing or
when the printer tray is in motion.
• The disc printing LED is solid green when the printer is idle.
• The disc printing LED is solid amber when the ink cartridge access
door is open.
Ink status
• The ink status LED is solid green when the cartridges are
functioning properly.
• The ink status LED is amber when the ink is low or out.
• The ink status LED blinks amber if the cartridges are not installed
properly.
110808_C 5
Rimage 360i
6 110808_C
Rear view
Power
Po
Filter
Rear
Switch
wer Cord
Port
Cover
Cove
r
USB 2.0
Port
Operate the Rimage 360i
Operate the Rimage 360i
This section provides the information that you need to produce CDs or DVDs with the Rimage
360i.
Powering on the Rimage 360i
1. To power on the 360i, press the power switch
on the rear of the 360i. The Rimage 360i
initializes.
2. To power off the 360i, press the power switch
again.
Pausing the Rimage 360i
Before you load or unload discs from the Rimage 360i, you must pause it.
1. To pause the 360i, press the pause button once. The
360i pauses. The power LED is amber.
2. To return to normal operation, press the pause button
again. The power LED is green.
110808_C 7
Rimage 360i
8 110808_C
Loading the discs
1. Open the input door.
2. Place up to 25 discs in the disc input with
the printable side facing out.
3. Close the input door.
Operate the Rimage 360i
Select your printing preferences
Printing Preferences allows you to set up and run your Rimage 360i to produce the best possible
label on your discs.
# Tip: For additional
information about these
features, access the
online help in Printing
Preferences.
Through Printing Preferences, you can:
• Set the print quality
• Adjust the ink volume used
• Change or enable masking
• Printing on hub with a stacking ring
• Printing on hub without a stacking ring
• Center the image on the disc
• Check the ink levels
• Add, edit, or delete a watermark
• Set up color options
• Align the ink cartridges
Navigating to Printing Preferences
You must access the Disc Color 360i Printing Properties window to set up your printing
preferences. Use either procedure below to navigate to the Disc Color 360i Printing Properties
window.
Accessing Printing Preferences through Windows Start menu
1. From the Windows Start menu:
• In Windows 2000, navigate: Settings > Printers.
• In Windows XP, navigate: Settings > Printers and Faxes.
2. Right-click on the Disc Color 360i and select Printing Preferences from the drop-down
menu. The Disc Color 360i Printing Properties window opens.
Accessing Printer Preferences through CD Designer
Note: Properties set in the label file will override the printer driver settings.
1. In CD Designer, open a label file.
2. From the File menu, select Print. The Print window opens.
3. From the Printer Name drop-down list, select Disc Color 360i.
4. Select the Document Properties button. The Disc Color 360i Properties window opens.
110808_C 9
Rimage 360i
10 110808_C
Setting the print quality
Use this procedure to change the print quality for your images, if necessary.
1. Navigate to Printing Preferences (refer to page 9).
2. Select the Disc/Quality tab.
3. In the Disc Options panel, select the appropriate Type from the drop-down list.
4. In the Print Quality panel, select the desired print quality. When you select a print quality, the
following information about the quality displays:
• Black render dpi
• Color input dpi
• Color output
5. If necessary, change digital photography options.
a. In the Print Quality box, select the Digital Photography button. The Digital Photography
Options window opens.
b. Select the desired options.
c. Select OK. The Digital Photography Options window closes.
6. When you have made the desired print quality changes, select OK. The Disc Color 360i
Properties window closes.
Adding, editing, or deleting a watermark
This functionality allows you to create a new watermark or edit a currently existing watermark that you
can print on your disc. From this tab, you can also delete a current watermark that you created.
1. Navigate to Printing Preferences (refer to page 9).
2. Select the Effects tab.
3. From the Watermarks drop-down list, select the desired watermark.
Or
If desired, edit the watermark or create a new watermark.
a. Select Edit. The Watermark Details window opens.
b. To delete a watermark, highlight the desired watermark and select Delete.
Note: You can delete only watermarks that you or another user has created. You cannot
delete any of the default watermarks.
c. To create a new watermark, select New. ‘Untitled’ displays in the Current Watermarks field.
d. Enter or change information in one or more of the following fields to create your customized
watermark:
• Watermark Message – Enter the desired message.
• Message Angle – Select the appropriate radio button to provide the desired angle. If you
select the Angle radio button, you can set the angle.
• Options – Select the Justified Across Page radio button to center and justify the text.
• Font Attributes – Select the desired font attributes from the drop-down lists.
e. Select OK. The Watermark Details window closes.
5. If you want the watermark to print only on the first disc, select the First Page Only checkbox.
7. When you have made the desired choices, select OK. The Disc Color 360i Properties window
closes.
Operate the Rimage 360i
Adjusting the ink volume used
This functionality allows you to adjust the amount of ink that is used.
1. Navigate to Printing Preferences (refer to page 9).
2. Select the Basics tab.
3. Select Advanced Features. The Advanced Features window opens.
4. To increase or decrease the ink volume or dry time, move the Ink Volume and Dry Time
sliders.
- Important! Do not select the Low Memory checkbox.
5. Select OK. The Advanced Features window closes.
8. When you have made the desired choices, select OK. The Disc Color 360i Properties window
closes.
Setting up color options
This functionality allows you to toggle between color and grayscale printing, select the type of
color space your labels require, and adjust some color attributes.
1. Navigate to Printing Preferences (refer to page 9).
2. Select the Color tab.
3. Turn Print in Grayscale on or off.
a. In the Color Options box, select or clear the Print in Grayscale checkbox.
b. If you selected the checkbox, select the appropriate radio button for your print type.
4. To adjust color attributes, move the Saturation, Brightness, and/or Color Tone sliders to
the desired position.
5. If necessary, select the appropriate Color Space from the drop-down list.
6. When you have made the desired choices, select OK. The Disc Color 360i Properties window
closes.
110808_C 11
Rimage 360i
12 110808_C
# Tip If you print on areas
of the disc where the
surface is not suitable
for printing, the ink can
smear or run.
Changing or enabling masking
This functionality allows you to adjust the non-printable area, or mask,
settings for standard CD/DVD 120 mm media.
1. Navigate to Printing Preferences (refer to page 9).
2. Select the Mask Settings tab.
3. To enable mask settings, select the Enable Masking checkbox.
4. Change the mask settings as desired.
5. When you have made the desired choices, select OK. The Disc
Color 360i Properties window closes.
Note: Select the Default button to return mask settings to the
factory settings.
# Tip: The image below
shows a disc with a
stacking ring.
#as
ink will
#
areas:
S
eter 38 mm
H
Inner Diameter 24 mm
Tip: If you print on are
of the disc where the
surface is not suitable
for printing, the
smear or run.
Tip: Most discs with a
printable hub and a
stacking ring have the
following printable
tandard Area
Outer Diameter 118 mm
Inner Diam
ub Area
Outer Diameter 35 mm
Printing on hub with a stacking ring
This functionality allows you to print on the hub area of the disc. If your
discs have a printable hub area, and there is a gap for the stacking
ring, use this procedure.
1. Navigate to Printing Preferences (refer to page 9).
2. Change mask settings.
a. Select the Mask Settings tab.
b. Select the Enable Masking checkbox.
c. In the Hub Area Settings box, select the Printing on Hub
checkbox.
3. Measure the printable area and adjust the settings.
a. Measure the inner diameter of the printable surface.
b. In the Hub Area Settings, enter the inner diameter that you
measured in step a.
c. Measure the outer diameter of the printable hub area.
d. In the Hub Area Settings, enter the outer diameter that you
measured in step c.
e. Measure the inner diameter of the standard printable area.
f. In the Standard Area Settings, enter the diameter that you
measured in step e.
4. After you have entered the correct measurements, select OK. The
Disc Color 360i Properties window closes.
Operate the Rimage 360i
# Tip: The image below
shows a disc with no
stacking ring.
# Tip: Rimage
recommends that you
set the inner diameter so
that it is 1 mm greater
than the actual
measurement to prevent
the ink from smearing.
The inner diameter on
Rimage media is 23 mm.
Set the inner diameter
field to 24 mm.
Printing on hub without a stacking ring
This functionality allows you to print on the full surface of a disc that
has no stacking ring. If you print on areas of the disc where the
surface is not suitable for printing, the ink can smear or run.
1. Navigate to Printing Preferences (refer to page 9).
2. Change mask settings.
a. Select the Mask Settings tab.
b. Select the Enable Masking checkbox.
c. In the Hub Area Settings box, select the Printing on Hub
checkbox.
3. Measure the printable area and adjust the settings.
a. Measure the inner diameter of the printable surface.
b. In the Hub Area Settings, change the Outer Diameter and
Inner Diameter settings to the value measured in step a before
changing any other diameter settings.
c. In the Standard Area Settings, change the Inner Diameter to
the same value used in step b.
4. After you have entered the correct measurements, select OK. The
Disc Color 360i Properties window closes.
Aligning the ink cartridges
For optimal print quality and maximum printing speed, use this procedure to align the ink cartridges.
1. Navigate to Printing Preferences (refer to page 9).
2. At the Rimage 360i, open the front cover.
3. Press the green (middle) button. The printer tray opens.
4. Align the ink cartridges.
a. From the Disc Color Printer 360i Printing Preferences window, select the Service tab.
b. Select the Service ToolBox button. The Rimage Service Toolbox window opens.
c. Select the Align Cartridges button. The Align Cartridges for Disc Color 360i dialog box opens.
d. To align the ink cartridges, follow the instructions in the Align Cartridges for Disc Color 360i dialog
box.
e. To close the Align Cartridges for Disc Color 360i dialog box, select OK.
5. To close the Disc Color 360i Printing Properties window, select OK.
6. To close the printer tray, press the green (middle) button. The printer tray closes.
7. Close the front cover.
110808_C 13
Rimage 360i
14 110808_C
Centering the image on the disc
The Rimage 360i provides two ways to center the image on the disc. You can use the Auto
Centering method or the Manual Centering method. The Auto Centering method is accurate to
within +/- 0.5 mm. You can improve the centering position accuracy with the manual centering
adjustment to better than +/- 0.2 mm. For optimal print quality, use this procedure to center the
image on the disc.
# Tip: Use the Center Image
functionality only if the
printed image is not
centered on the disc. Image
centering is set at the time
of manufacture and usually
does not need to be
recalibrated in the field.
1. Navigate to Printing Preferences (refer to page 9).
2. At the Rimage 360i, open the front cover.
3. To open the printer tray, press the green (middle) button inside the
front cover of the Rimage 360i. The printer tray opens.
4. On the Service tab, select the Service ToolBox button.
5. Select the Center Image button. The Centering Margins for Disc
Color 360i dialog box displays.
6. Follow the directions in the dialog box to:
Auto center the image
Or
Manually center the image
7. When the image is centered, select OK to close the Centering
Margins for Disc Color Printer 360i dialog box.
8. To close the Rimage Service ToolBox window, select OK.
9. To close the Disc Color 360i Properties window, select OK.
10. To close the printer tray, press the green (middle) button. The printer
tray closes.
11. Close the front cover.
# Tip: If you remove the ink
cartridges and reinsert
them, the system resets to
show that the cartridges are
full, regardless of the actual
fill status.
Checking the ink levels
This functionality allows you to check the level of ink in the cartridges.
1. Navigate to Printing Preferences (refer to page 9).
2. On the Service tab, select the Service ToolBox button.
3. Select the Get Ink Level button. Ink level information displays in the
Printer Status field.
4. To close the Rimage Service ToolBox window, select OK.
5. To close the Disc Color 360i Properties window, select OK.
Maintain the Rimage 360i
Maintain the Rimage 360i
The procedures in this section will help keep your Rimage 360i in optimum operating condition.
General Cleaning
# Tip: To keep your Rimage 360i
clean, keep it in a dust free
environment.
Cleaning the exterior
If your Rimage 360i becomes dusty:
1. Power off the Rimage 360i.
2. Wipe the exterior with a damp, lint-free cloth.
# Tip: Use only Rimage inkjet print
cartridges and, for best results,
follow the guidelines below:
• Keep print cartridges sealed in
the original package until they
are needed.
• Store print cartridges at room
temperature (60 - 78 degrees
F or 15.6 to 26.6 degrees C)
• Store print cartridges in an
upright position - not on their
sides or upside down.
• Do not remove the protective
tape from a new print cartridge
until just before you install it.
Once you remove the tape, do
not reapply it.
• After you have removed the
protective tape, avoid touching
the contacts and nozzles.
• Print at least once a month to
keep the print cartridges in
good working order.
Cleaning the ink cartridge nozzles
This functionality allows you to clean or open the ink cartridge
nozzles. The nozzles may become clogged from dried ink
causing poor print because one or more nozzles are not
delivering the appropriate quantity of ink.
1. Navigate to Printing Preferences (refer to page 9).
2. On the Service tab, select the Service ToolBox button.
3. Select the Clean Cartridges button. The Cleaning
Cartridges window opens.
4. To clean the ink cartridge nozzles using the least amount
of ink, select Light. The status field at the bottom of the
Cleaning Cartridges window displays a message when the
cleaning is complete.
Note: Print a test disc after cleaning the ink cartridge
nozzles. If the print quality is poor, repeat this process
and, in step 4, select Medium or Heavy to clean the ink
cartridge nozzles.
5. To close the Cleaning Cartridges window, select OK.
6. To close the Rimage Service ToolBox window, select OK.
7. To close the Disc Color 360i Properties window, select
OK.
110808_C 15
Rimage 360i
16 110808_C
Replace Consumables
Replacing the fan filter
The fan filter is a consumable item. You will need to change the fan filter after 20 ink cartridges.
Use this procedure to change the fan filter.
1. On the rear of the Rimage 360i, press the tab
on the filter cover and lift up the filter cover.
2. Remove the filter.
3. Place the new fan filter in the fan filter retainer.
4. Firmly press the fan filter cover back into
place.
Maintain the Rimage 360i
Replacing the ink cartridges
Use this procedure to change the ink cartridges on your Rimage 360i.
- Important! You must use the appropriate ink cartridges in one of the configurations as stated
on page 1 of this document.
1. Open the ink cartridge access door. The ink
cartridge carriage moves to an accessible position on
the carriage guide.
2. When the ink cartridge carriage has stopped moving,
lift the ink cartridge latch to the open position.
3. Remove the installed ink cartridge.
4. Remove a new ink cartridge from its packaging and
carefully remove the protective tape that covers the
ink nozzles.
- Important! Do not touch the nozzles or the copper
contacts on the ink cartridges. Do not remove the
copper strips.
5. Slide the ink cartridge into the cradle.
6. Push down on the ink cartridge latch until it snaps
closed.
7. Close the ink cartridge access door.
Note: If the ink cartridge is not securely seated in the
cradle, the printer will not recognize the ink cartridge.
The printer may not reset properly or you may
receive an “invalid ink cartridge” message. If this
happens:
a. Remove the cartridge and reinsert it.
b. Make sure you are using the appropriate
cartridge. Acceptable cartridges are listed in
the Ink requirements section on page 1.
c. If the problem persists, replace the cartridge.
8. Using the
Aligning the ink cartridges procedure on
page 13, align the ink cartridges.
110808_C 17
Rimage 360i
18 110808_C
Learn More
Rimage 360i Specifications
Standard System One disc recorder, Rimage 360i with Rimage 360i Disc Color
Printer, and software.
Software requirements Rimage 360i Software
Input bin capacity 25 Discs
Output capacity 25 Discs
Physical size Width – 15.25” (38.7 cm)
Height – 19.00” (48.3 cm)
Depth – 20.00” (50.8 cm)
Weight – 25 lb (11.34 kg)
Minimum PC
requirements
If you do not understand these
requirements, ask your computer
technician for help or refer to your
PC documentation.
Processor: Pentium III, 800 MHz or higher
RAM/Memory: 256MB
Fixed Storage: 2 GB of free space
Graphics: 1024 x 768 High Color
I/O: One USB 2.0 port
Supported Operating
Systems Windows 2000 SP4, Windows XP SP1 or SP2, Windows 2003
Power 100 – 240 VAC, 1.5 A, 60/50 Hz
Operating Temperature 60° to 95° F (16° to 35°C)
Humidity 40 to 80% non-condensing
Storage Temperature 5° to 95° F (-15° to 35°C)
Learn More
Technical support and product updates
Support for the Rimage 360i is available through your authorized reseller.
- Important! Register your Rimage 360i online or complete and return the registration card so
Rimage can notify you of upgrades as they become available.
Safety information
This manual and the indications on the product allow proper and safe operation. The indication
marks below help protect you and other persons from injury, and equipment from damage.
narning is
at could result in bodily injury to personnel operating or
p eline could result in loss or damage to the
re, or data.
autions in the User Guide and familiarize yourself with their
p ame type
n
n Warning! Ink may be harmful if swallowed. Avoid contact with eyes. Ink contains nitrites. If
ingested, seek immediate medical attention. Keep out of reach of children.
Warning! According to ANSI (American National Standards Institute) standards, a w
used to indicate situations th
maintaining the equipment.
Caution: Indicates that failure to observe this guid
equipment, product, softwa
Safety precautions
To ensure safety, please read the prec
meaning before using the equipment.
Caution: For continued protection against risk of fire, replace the fuse only with s
and rating. An authorized technician should perform all service procedures.
Warning! The laser beam used by this CD Recorder is a Class 1 laser. Do not attempt to
open the recorder. An authorized technician should perform all service procedures.
110808_C 19
Rimage 360i
20 110808_C
Safety testing
Product name: Rimage 360i
Model: RAS17
Notice for USA
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This product complies with UL 60950-1.
Notice for Canada
This Class B digital apparatus complies with Canadian ICES-003 Issue 3:1997. Cet
appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
This product complies with CAN/CSA-C22.2 No. 60950-1-03
Notice for Europe
C
This product is in conformity with the EMC Directive (89/336/EEC) and the Low-Voltage
Directive (73/23/EEC) through compliance with the following European standards:
EN 55022: 1998 + Amd 1: 2000 Class B Limit; EN 55024: 1998; EN 61000-3-2:2000;
EN 61000-3-3:1995 + Amd 1: 2001; EN 60950: 2000. The CE mark has been affixed in
accordance with the CE Marking Directive 93/68/EEC.
Notice for Japan
This product complies with VCCI V.3/2004.04
Learn More
Rimage 360i Limited 1 Year Warranty
Rimage warrants, to the original end user only, that all non-consumable parts of the Rimage 360i Autoloader
products will be free from defects in material and workmanship for 12 months, according to the following
terms:
• Rimage will provide 30 days of free telephone support beginning on the day that the Rimage software is
activated. Telephone support after the free 30 day period will be provided pursuant to Rimage’s then
current standard support charges.
• Rimage will replace or repair, at Rimage's discretion, any non-consumable parts found defective within
the Warranty period.
• Valid from the date that the Rimage software is activated.
• Factory depot repair:
To Rimage’s US depot repair location from a location within the US or Canada with a typical
response of 15 business days.
To Rimage’s European depot repair location from a location in Europe with a typical response of 15
business days.
To Rimage US depot repair from a location that is not in the US or Canada with a typical response
of up to 25 business days.
• Advanced Replacement or faster response Maintenance Contracts are available for an additional fee.
• Rimage will pay ground service freight charges for components shipped to you.
• Covers normal office-environment use in the country of original purchase.
The use of non-Rimage certified parts may void this warranty.
The use of non-Rimage ink cartridges or refilling of ink cartridges voids the equipment warranty or maintenance
coverage. Any applicable ink cartridge warranty shall not apply to Rimage ink cartridges that have been refilled,
remanufactured, refurbished, misused, or tampered with in any way.
This Warranty does not include the following:
• Work done at the customer's location, or customer's loss of data.
• Shipment costs of equipment or components returned to the Rimage factory.
• Equipment malfunctions as a result of repairs made by technicians who are not authorized or certified
by Rimage.
• Equipment or parts that were tampered with, misused, neglected, or that were modified in any respect
without the written consent of Rimage.
• Equipment or parts that have been damaged due to shipping or accidents, or damaged by lightning,
storms, water, or power surges.
• Printer consumables including ink cartridges or print head.
You may not assign this Warranty without Rimage's written consent. Rimage is the intended beneficiary of
this Warranty; if there is any inconsistency between this Warranty and any other agreement included with or
relating to Rimage products, this Warranty shall govern. If any term of this Warranty is illegal or
unenforceable, the legality and enforceability of the remaining provisions are not affected or impaired. This
Warranty is to be interpreted under the laws of the State of Minnesota, without giving effect to conflict of law
rules.
Rimage must receive written notice of any claimed defect or failure to perform within five (5) days after such
failure or defect is first observed. For warranty service, contact Rimage at the telephone numbers listed on
the Warranty Contact Sheet.
The Limited Warranty set forth above is Rimage's only Warranty in connection with the Rimage 360i
Autoloader product. All other Warranties, whether written or oral, express or implied, contractual or
statutory, including, but not limited to any Warranties of merchantability or fitness for any particular purpose
are specifically excluded and disclaimed. In no event shall Rimage's liability under this Warranty exceed the
obligation to repair or replace, at Rimage's discretion, a Warranted product, and, without limiting the
foregoing, Rimage's liability under this Warranty shall not exceed the cost of the covered product.
110808_C 21

Navigation menu