Ring BHADB001 Steplight User Manual Ring Video Doorbell Setup and Installation Guide

Ring LLC Steplight Ring Video Doorbell Setup and Installation Guide

User manual

Beams Step Light
136mm
110mm
1. Connect your
Step Light.
Download the Ring app.
The app walks you through setting up and managing your
Step Light.
Search for “Ring” in one of the app stores below, or visit:
ring.com/app
Set up your Ring Beams Bridge.
The Bridge connects your Ring Beams lights to
the rest of your Ring system. Your Bridge must
be up and running before you set up your Step Light.
To set up your Bridge, follow the instructions in the Ring
app or Bridge user manual.
Download from
Windows Store
3
Remove the screws from
the back, and lift off the
battery lid.
Insert three C-cell
batteries.
Beams
Alarm
Doorbells
Security Cams
Chimes
Set up your Step Light
in the Ring app.
In the app, tap
Set Up a Device.
When prompted, select
Beams and follow the in-
app instructions.
Insert the batteries.
54
2
2. Install your Step Light.
Use the lid as a template
to mark the screw
locations.
Push the lid back onto
your Step Light, and
secure it with the screws
you removed.
Drive the two mounting
screws, leaving ~1/4”
exposed.
Place your Step Light
over the mounting
screws, then push
downward to lock it in
place.
Your Step Light detects motion best when
mounted ~2 feet above the ground.
76
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any inte rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interferenceto radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
ISED Statement
English: This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This d
evice must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
‐ French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas p
roduire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi
le brouillageest susceptible d'encompromettre le fonctionnement.
Radiation Exposure Statement
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
Déclaration d'exposition aux radiations
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non
contrôlé. Cet équipement doit être installé et utilisé à distance minimum de 20cm entre le radiateur et votre
corps.

Navigation menu