5AT1S9_User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 4125276 |
| Application ID | eBhtm5FGjkdAcTNeXXhRoQ== |
| Document Description | 5AT1S9_User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 121.06kB (1513282 bits) |
| Date Submitted | 2019-01-01 00:00:00 |
| Date Available | 2019-01-01 00:00:00 |
| Creation Date | 2018-12-31 14:18:20 |
| Producing Software | ç¦æ˜•PDF编辑器打å°æœºç‰ˆæœ¬8.3.0.0331 |
| Document Lastmod | 2018-12-31 14:18:20 |
| Document Title | 5AT1S9_User Manual |
Beams Landscape Transformer Landscape_Transformer_Manual_Cert.indd 1 10/11/18 4:58 PM 1. S et up your Ring Beams Landscape Transformer. Download the Ring app. The app walks you through setting up and managing your Landscape Transformer. Search for “Ring” in one of the app stores below, or visit: ring.com/app Download from Windows Store Choose a location. Ring Landscape Transformer Mounting Screw Template (FOR TESTING ONLY - DO NOT PRINT) Top Screws You’ll have to plug in your Transformer, so the best spot for it is near an exterior outlet. Once you’ve found a spot, use the mounting template to mark the screw holes. Mount the Transformer. Bottom Screw Tighten screws until heads are 1/8” (~3.2 mm) above your mounting surface. Drive the screws at the marked locations, leaving 1/8” of space between the surface and screw head. Align the slots on the rear of the Transformer with the screws. Slide the Transformer down over the screws to lock it into place. Landscape_Transformer_Manual_Cert.indd 3 10/11/18 4:58 PM 2. Install lights and wiring. Choose a cable. Select a cable to wire your Transformer to your light fixtures using the chart below. Place light fixtures. Decide where you would like to place your lights, and arrange them in the desired locations. Connect to Transformer. Open the wiring cover to expose the terminals, and lock the door in place. Strip and split the cable. Feed one end into the Common terminal, and the other into the 12V or 15V terminal, based on the cable you chose. Close the wiring cover. Then run the cable to each fixture, making the necessary connections. Landscape_Transformer_Manual_Cert.indd 5 10/11/18 4:58 PM 3. C onnect your Transformer to the Ring app. Plug the Transformer into the power outlet. Once plugged in, your Transformer and light fixtures will power on automatically and connect to the Ring app. Complete Setup in the Ring app. In the app, tap Set Up a Device. When prompted, select Beams and follow the in-app instructions to complete setup. Doorbells Security Cams Chimes Beams Congratulations! Your Landscape Transformer is ready to manage your lighting. Alarm If either the Transformer or light fixtures don’t power on, unplug the Transformer, check your connections and try again. Landscape_Transformer_Manual_Cert.indd 7 10/11/18 4:58 PM For additional help, visit: ring.com/help Or give us a call… US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents © 2018 Ring LLC or its affiliates. RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates. Last updated: 10/11/18 Landscape_Transformer_Manual_Cert.indd 8 10/11/18 4:58 PM Warnings This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement. MPE Reminding To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Author : Create Date : 2018:12:31 14:18:20+08:00 Modify Date : 2018:12:31 14:18:20+08:00 Subject : Has XFA : No Language : en-US XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : Description : Title : Creator Tool : Metadata Date : 2018:12:31 14:18:20+08:00 Keywords : Producer : 福昕PDF编辑器打印机版本8.3.0.0331 Document ID : uuid:4d8a30f0-d678-40ef-85d5-85be69c5b1c1 Instance ID : uuid:88745052-8609-462e-9f2f-49efd1de3d1a Page Count : 7EXIF Metadata provided by EXIF.tools