Ring BHARG031 Ring User Manual Ring Doorbell Users Manual 10 13

Bot Home Automation, Inc. Ring Ring Doorbell Users Manual 10 13

User manual

VIDEO DOORBELLQuick Install GuideTABLE OF CONTENTSCOMPONENTS................................................... 3BATTERY CHARGING....................................... 6WI-FI SETUP ...................................................... 7INSTALLATION................................................... 7HARDWIRING .................................................... 8ANSWERING A CALL....................................... 9MAC ID: XXXXXXXXXXXS/N: XXXXXXXXXXXProduct name: RingFCC ID: 2AEUPBHARG031Model name: Video DoorbellPower input: 8-24 VAC, 5Vdc 1 A1346781. Wide Angle HD Camera2. Microphone3. LED Ring4. Push Button5. Speakers256. Setup Button7. Micro USB Charging Port8. MAC AddressFRONT BACK2 3 4With Ring, you’realways home.910119. Doorbell Wire Terminals10. Mounting Hooks11. Wire Management HooksMOUNTING BRACKET 5
WI-FI SETUPDownload the Ring app from the App StoreGoogle Play or Windows Store. Open theRing app and select Setup Device. Followthe in-app instructions to set up your Ring.You will need your network information(SSID and password) to complete yourRing setup.INSTALLATION1. Remove doorbell button and power off yourtransformer (for wired installation only).2. Line up the mounting bracket using the provided mounting level.4. Install the mounting bracket using the providedscrewdriver bit, handle and drill bit. Brick - use provided screws and anchors Concrete - use provided screws and anchors Stucco - use provided screws and anchors Wood - use provided screws Vinyl - use provided screws5. Remove the mounting level.6. Connect your doorbell wiring to the terminal screwslocated on the mounting bracket(for wired installation only).7. Place the device on the mounting bracket.8. Tighten the security screws at the bottom of the deviceusing the proprietary screwdriver bit. Please do notover-tighten the security screws.9. Provide power back to your transformer(for wired installation only).HARDWIRING REQUIREMENTSIf powering off doorbell wiring, the wiringmust be connected to a transformer and adoorbell with a voltage of 8VAC - 24VAC toring your doorbell chime.BATTERY CHARGINGCharge your device using a USB-compatible wall chargeror laptop. To ensure your device is fully charged, chargethe device prior to Wi-Fi setup and installation.LED RING LIGHTING SEQUENCESBattery ChargingBattery ChargingCompleteCall InitiatedCall ConnectedHardwiredSetup ModeSoftware UpdateFactory ResetLED Ringspins blue.LED Ring staysfully lit blue.LED Ring spinsblue, then white.LED Ring staysfully lit blue.LED Ringspins white.LED Ringblinks white.LED Ringblinks blue.ANSWERING A CALLMute VolumeDisable MicrophoneEnd CallCall ZoomTo disable notications for your Ring device,select it from “My Devices”. Select “DeviceSettings” and toggle notications off.6 7 8 9If your chime is electronic (e.g. plays a melody), youmay need to install a diode, which is commonly foundinside your current doorbell button, or check with yourdoorbell manufacturer.Connect the diode to the terminals with the arrowon the diode facing towards the doorbell chime as shown below.LED Ring staysdimly lit white.For additional product information andhelpful tips, check out our supportforum at:http://ring.com/help For immediate assistance,please call us at:DOMESTIC: 1-800-656-1918INTERNATIONAL: +1 310-929-70857 days a weekCUSTOMER SUPPORT1523 26th St.Santa Monica, CA 9040410Protect the device from direct sunlight. Install the device at dry locations and protect itagainst rain and humidity. The device may not get contact to salt water or otherconductive liquids. The device must be charged only within a building in a dry state.Hereby, Bot Home Automation, declares that this consumerelectronic is in compliance with the essential requirementsand other relevant provisions of Directive 1999/5/EC. Thedeclaration of conformity may be consulted atwww.ring.com/DoC.pdf.AT&T11:56 AMEND CALLFrontTransformerRearTransformerElectronicChimeACINDiode
FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure StatementThis device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu