Contents
- 1. Users Manual 1
- 2. Users Manual 2
- 3. Users Manual 3
Users Manual 2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1044891 |
| Application ID | yB72T1YKfCLr9tsuN65y4g== |
| Document Description | Users Manual 2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 34.41kB (430083 bits) |
| Date Submitted | 2008-12-16 00:00:00 |
| Date Available | 2008-12-18 00:00:00 |
| Creation Date | 2008-11-11 12:18:41 |
| Producing Software | Acrobat Distiller 6.0.1 (Windows) |
| Document Lastmod | 2008-11-11 12:18:41 |
| Document Title | untitled |
Introduction
RISCO Group's 2-Way Wireless I/O & X10 Module is an extension module enabling wired
devices to be connected to the Agility Wireless system.
The Wireless I/O Module supports 4 hardwired zones, 4 outputs and controls up to 16 X10
devices.
Each output or X10 device can be operated in a response to a wide variety of system events.
For detailed information regarding the programming options of the Wireless I/O Module
refer to the installation manuals of the Agility.
Main Features
Bi-directional wireless communication
2 Relay Outputs (3Amp)
2 Transistor Outputs (500 mA)
4 Inputs (NO, NC, EOL)
Fully supervised
Dual tamper protection (Box & Wall)
X10 adapter, up to 16 X10 devices
Wireless I/O Module - Main Components
1.
RF Module
2.
Input Terminals
3.
Relay Output Terminals
4.
Transistor Output terminals
5.
AC Power terminals
IN1 GND IN2 IN3 GND IN4 NO1 C1 NC1 NO2 C2 NC2 VO3 GND VO4 V11 V12
RF Module
(parallel connection to J2)
6.
Back/Wall tamper (not visible)
7.
J2 Power socket
8.
3 LED indication
9.
RJ11 connector (X10 connection)
10. Box tamper switch
11
11. Battery holders=
10
Figure 1: Wireless I/O Module Main Components
Page 1
LED Indications
LED
(Red)=
(Yellow)
State
Power
Description
On
AC and batteries OK
Flashing
AC trouble or Low battery (below 3.1 VDC)
Off
Power not present
On
X10 Connected to the Wireless I/O Module
Off
X10 Disconnected
On
The I/O expander is communicating with the Agility
Off
No communication is taking place
X10
Communication
(Green)
Mounting the Wireless I/O Module
Select a mounting location near an AC power supply in proximity to the Agility main panel
1.
Open the cover by twisting a screwdriver in the slots on the bottom or top of the case
(Figure 2).
Figure 2: Opening the Cover
2.
Figure 3) and open knockouts for the entry of the power wires
Remove the circuit board (
(1, Figure 4) and for the back tamper (2, Figure 4).
Page 2
3.
Mount the receiver on the wall using the installation holes (3, Figure 4) and reinstall the
circuit board. Make sure that that you hear a "click" when attaching the tamper spring to
the wall.
UO1
Z3 3 COM Z3 4 Z35 COM Z36 N O C NC
NO
UO2
C NC UO3 C OM UO4
AC
Figure 3: Circuit Board Removal
4.
Figure 4: Knockouts and Installation Holes
Connect the power source wire plug to the J2 power jack on the PCB or to the AC
terminals on the PCB. The polarity is not important.
Do Not
plug the transformer into the
wall outlet at this point.
5.
Optional back-up batteries: Plug in three rechargeable batteries (size AA NiMH
2300
mAH) into the battery holders. Pay attention to the correct polarity (+) (-).
NOTE:
Rechargeable batteries should be charged for at least 24 hours.
IMPORTANT
When replacing the batteries be sure to use the same type. Failure to comply with this
instruction may result in damage to personnel and/or equipment. Dispose of used batteries
according to local regulations.
6.
Set all inputs and output wiring, as described below.
Page 3
Wiring the Wireless I/O module
Inputs wiring
The
Agility supports 4
hardwire zones (defined in the Agility system as zones 33-36) that can
be defined as Normally Open, Normally Closed or End of Line Zones.
The following diagram illustrates the various zone connections:
NORMALLY CLOSED
ZONE CONFIGURATION
NORMALLY OPEN ZONE
CONFIGURATION
COM
COM
END OF LINE ZONE
(N.C CONTACT)
END OF LINE ZONE
(N.O CONTACT)
COM
COM
2.2 K
ALARM
ALARM
DEVICE
DEVICE
DEVICE
ALARM
DEVICE
ALARM
Utility Outputs wiring
The
Agility includes
4 utility outputs (2 x 24VDC 3Amp relays and 2 x 13.8 VDC 500 mA
transistor outputs). These outputs can operate external devices in response to a number of
system activities. For detailed information regarding the programming of the utility outputs
refer to the Agility Installer Guide.
To wire Relay Outputs (UO1, UO2)
Wire the devices that you want to activate to the outputs, as follows:
NOTE:
UO1 and UO2 connections are identical.
NC: Normally closed contact
C: Common
contact
NO: Normally
open contact
NORMALLY OPEN OUTPUT
CONFIGURATION
N.O
UO
N.C
NORMALLY CLOSED OUTPUT
CONFIGURATION
N.O
UO2 / UO1
EXTERNAL
POWER
UO
EXTERNAL
POWER
UO1/UO2 behave as dry contacts
Page 4
N.C
To wire Transistor Outputs (UO3-UO4)
Connect the positive connection of the device to
to the GND
(-)
UO3 or UO4 (+)
and the negative connection
terminals.
UO3 COM
X10 Connection
UO4
EXTERNAL
POWER
The wireless I/O expander enables the Agility to control X10 devices. The I/O expander
converts the information sent from the programmable utility output into the X10 protocol. Up
to sixteen X10 devices can be activated. These are recognized in the system as outputs 5 to 20.
To connect the X10
Connect the X10 controller cable to the RJ11 connector located on the Wireless I/O module
PCB.
Transmitter/Receiver Communication Setup
To set up the communication with the receiver, the I/O expander should identify itself to the
system's receiver in the same way as setting communication to a wireless zone.
IMPORTANT:
Before proceeding with the steps below, plug the AC transformer into the wall outlet.
1.
Set the security panel to Learn mode.
2.
Send a WRITE message by pressing the Wall and Cover tampers switches
simultaneously for at least 3 seconds (when the PCB IS installed ONLY the cover tamper
has to be pressed).
3.
Verify that the I/O expander has been identified by the security panel.
4.
Install the Wireless I/O Module front cover back in its place. Lock screw located at the
top of the unit.
Programming
Changing Default Settings
Via the Agility panel you can define the Inputs, Outputs and X10 parameters settings
according to your requirements.
For more information refer to the Agility Installer Manual.
Page 5
Diagnostics
You can perform diagnostic tests and check the status of the Inputs, Outputs connected to the
Wireless I/O Module and the communication between the module and the Agility. The
diagnostics can be performed locally from a keypad or remotely from the Configuration
Software.
Technical Specifications
Electrical Characteristics
Power Supply
9VAC, 0.5A minimum
Current Consumption
(Minimum / Maximum)
20 mA minimum / 150 mA maximum
Backup Batteries
3 x size AA NiMH cylindrical cell 1.2V 2300 mAH
Relay Outputs
2 x 3 Amps 24 VDC programmable
Transistor Outputs
2 x 500mA transistors (Open Collector)
Operating Temperature
-10°C to 40°C (32°F to 131°F)
Storage Temperature
-20°C to 60°C (-4°F to 140°F)
Physical Characteristics
Dimension
14.5 cm x 9.0 cm x 4.0 cm (5.7 x 3.54 x 1.57 inch)
Weight (with batteries)
0.24 Kg (0.52lb)
Wireless Characteristics
RF immunity
According to EN 50130-4
Frequency
868.65 MHz or 433.92 MHz
Compliance
EN50131-1, EN50131-3 Grade 2
EN50130-5 Environmental class II
EN50131-6 Type A
Ordering Part Numbers
Part number
Description
RW132I04000A
2-Way Wireless I/O & X10 Module, 868.65 MHz
RW132I04000H
2-Way Wireless I/O & X10 Module, 433.92 MHz
Page 6
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
JE4AGILITY Valid for P/N RW132I04000H
6564A-AGILITY Valid for P/N RW132I04000H
FCC ID:
IC:
FCC Warning
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment.
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in
materials and workmanship under normal use for 24 months from the date of production. Because Seller
does not install or connect the product and because the product may be used in conjunction with
products not manufactured by the Seller, Seller can not guarantee the performance of the security system
which uses this product. Sellers' obligation and liability under this warranty is expressly limited to
repairing and replacing, at Sellers option, within a reasonable time after the date of delivery, any product
not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes no
warranty of merchantability or of fitness for any particular purpose. In no case shall seller be liable for
any consequential or incidental damages for breach of this or any other warranty, expressed or implied,
or upon any other basis of liability whatsoever. Sellers obligation under this warranty shall not include
any transportation charges or costs of installation or any liability for direct, indirect, or not be
compromised or circumvented; that the product will prevent any persona; injury or property loss by
intruder, robbery, fire or otherwise; or that the product will in all cas es provide adequate warning or
protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of
intruder, robbery or fire without warning, but is not insurance or a guaranty that such will not occur or
that there will be no personal injury or property loss as a result. Consequently seller shall have no
liability for any personal injury, property damage or loss based on a claim that the product fails to give
warning. However, if seller is held liable, whether directly or indirectly, for any loss or damage arising
from under this limited warranty or otherwise, regardless of cause or origin, sellers maximum liability
shall not exceed the purchase price of the product, which shall be complete and exclusive remedy against
seller. No employee or representative of Seller is authorized to change this warranty in any way or grant
any other warranty.
WARNING: This product should be tested at least once a week.
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us
through our website www.riscogroup.com or as follows:
United Kingdom
USA
Tel:+44-161-655-5500
Tel:+305-592-3820
sales@riscogroup.co.uk
sales@riscogroupusa.com
technical@riscogroup.co.uk
support@riscogroupusa.com
Italy
Brazil
Tel: +39-02-66590054
Tel:+55-11-3661-8767
info@riscogroup.it
sales-br@riscogroup.com
support@riscogroup.it
support-br@riscogroup.com
Tel:+34-91-490-2133
Tel: +86-21-52390066
sales-es@riscogroup.com
sales-cn@riscogroup.com
support-es@riscogroup.com
support-cn@riscogroup.com
Tel: +33-164-73-28-50
Tel: +48-22-500-28-40
sales-fr@riscogroup.com
Fax: +48-22-500-28-41
support-fr@riscogroup.com
support-pl@riscogroup.com
Tel: +32-2522 7622
Tel: +972-(0)3-963-7777
sales-be@riscogroup.com
info@riscogroup.com
support-be@riscogroup.com
support@riscogroup.com
Spain
France
Belgium
China
Poland
Israel
All rights reserved.
No part of this document may be reproduced in any form without prior written permission
from the publisher.
© RISCO Group
05/08
5IN1038
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 8 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:95f6b51f-8537-4725-b3a4-a8a9d2340da6 Producer : Acrobat Distiller 6.0.1 (Windows) Modify Date : 2008:11:11 12:18:41+02:00 Create Date : 2008:11:11 12:18:41+02:00 Document ID : uuid:be3325a4-5b70-4fbc-99ed-28fbdd4468aa Format : application/pdf Title : untitled Creator : Author :EXIF Metadata provided by EXIF.tools