Rising Digital SECD-3I5A-02 SECD-3I5A-02display screen User Manual Manual

Shanghai Rising Digital Co.,Ltd. SECD-3I5A-02display screen Manual

Manual

1st Shanghai Rising Digital Co.,Ltd. SECD-3I5A-02 USER MANUAL Document Number： Dense level： Version Number： V1.2
2ndShanghai Rising Digital Company Revision History Version Date AMD Reviser Instructions Approval 1.0 2012-09 A Hongliang Liu, Xiang Gao Creation （A-Add，M-Modify，D-Delete）
3rd SECD-3I5A-02(4GVersion) 1、Hardware performance indicators 1) Voltage input： ¾ circuits：4 ¾ signal：0～5V.DC ¾ precision：0.5% ¾ resolution：0.025% 2) Resistance input ： ¾ circuits：2 ¾ precision：0.5% ¾ resolution：0.025% 3) Discrete input（low level）： ¾ circuits：5 ¾ signal peak：0～40V.DC ¾ frequency：0Hz～1KHz 4) Discrete input（high level）： ¾ circuits：2 ¾ signal peak：0～40V.DC ¾ frequency：0Hz～1KHz 5) Periodic input： ¾ circuits：1 ¾ signal peak：1.2～40V.DC ¾ range：10Hz～70KHz ¾ precision：0.1% 6) PWM output： ¾ circuits：1 ¾ frequency：50～2.55kHz ¾ current：0～0.75A ¾ precision：1% ¾ resolution：0.025%
4th¾ features：overpressure、short circuit protection 7) Motor driver output： ¾ circuits：4（one stepper motor） ¾ contact capacity：40V.DC 1.2A ¾ frequency：0Hz～3KHz ¾ features：overpressure、short circuit protection 8) Digital output： ¾ circuits：4 ¾ contact capacity：40V.DC 1.8A ¾ frequency：0Hz～1KHz ¾ features：overpressure、short circuit protection 9) Analog output： ¾ circuits：1 ¾ signal peak：0～5V.DC ¾ precision：0.5% ¾ resolution：0.025% 10) Communication interface： ¾ CAN：1circuit，Rate of optional，ISO11898 CAN 2.0B、J1939 ¾ Communications link：1circuit，4G/GSM  North American version- frequency band LTE-FDD B2/4/5/12/17，WCDMA B2/4/5，GSM 850/1900  The European version—frequency band LTE-FDD B1/3/5/7/8/20，WCDMA B1/5/8，GSM 850/900/1800/1900  The Chinese version—frequency band LTE-FDD B1/3/8，LTE-TDD B38/39/40/41， WCDMA B1，TD-SCDMA B34/39， GSM 900/1800 ¾ GPS link：1 circuit 11) Display parameters： ¾ resolution：320×240（3RGB） 12) Other indicators ¾ kernel： TMS320F28335（32bit DSP） ¾ proposed kernel：112.5MHz ¾ duty cycle： ≤5 ms
5th¾ power supply： 18～36V.DC（Under the recommended voltage 24 v DC 36 v can't work for a long time） ¾ output voltage： 5V.DC，0.75A ¾ Current consumption： 0.2A.DC（24V.DC） ¾ Working temperature： -20～+65℃ ¾ Storage temperature： -25～+80℃ ¾ overvoltage protection： 37.2V ¾ high temperature protection：80℃ ¾ protection grade： IP65，all-round protection ¾ relative humidity： 10％～90％ ¾ overall dimensions： 183mm×127mm×51.5mm
6th2、Installation drawing Front view
7th Rear view
8th Right side chart
9th Figure of the side
10th3、Pin definition
11th4、Terminal blocks that： Signal name Parameter I/O type Unit Range Precision Terminal number Instructions Positive +24VIN Analog input V 18～36 J1-25, J1-34 Analog output without load (open), switch output without load (open), PWM output without load (open), the standard + 24 VDC power supply, the current consumption of about 0.2 A. Negative GND Analog input V 0 J1-8,J1-24,J1-33 Voltage input AI_V_i （i＝4） Analog input V 0～5 0.5% J1-21,J1-29,J1-30， J1-32 Resistance input AI_R_i （i＝2） Analog input Ω 0～130 0.5% J1-23,J1-31 A/DAIGND+5VOUTA/DAIGND
12thSignal name Parameter I/O type Unit Range Precision Terminal number Instructions Discrete input （low level） DI_L_i （i＝1～5） Digital input V 0～40 J1-6,J1-12,J1-13, J1-14,J1-15 Discrete input （high level） DI_H_i （i＝2） Digital input V 0～40 J1-4,J1-5 Periodic input TI_i （i＝1） Digital input Hz 10～70000 0.1% J1-3 Analog output A0_i （i＝1） Analog output V 0～5 J1-22 I/OGNDDIPII/OPI+24VI/O+24VDI
13thSignal name Parameter I/O type Unit Range Precision Terminal number Instructions PWM output PWM_i （i＝1） Analog output A 0～1.5 1% J1-10 CAN high level line CAN_H Digital input output V 2.5～5 0～2.5 J1-2 CAN by way of bus connection，terminal 120Ω resistance CAN low level line CAN_L J1-1 Program reshipment jump line RS Digital input J1-7 RS short, after receiving the program can be heavy on electricity. +5V power output +5VOUT Analog output V 5.0 ±5% J1-9 The external device, such as sensor with power supply Sleep mode input SMI Digital input V 0～36 J1-17 1) 0<SMI<6.5V The controller into sleep mode; 2) 11V<SMI<36V) Controller into the normal working mode. Motor driver output MO_i （i＝4） Digital output V 0～36 J1-11,J1-16 J1-19,J1-20
14th 5、Matters needing attention： ¾ 1、besides display shell well grounded, all connected to display the load, and so on input and output points must connect into a closed loop, which all of the input and output must be connected with display corresponding to. ¾ 2、4G, GPS antenna installation, pay attention to the antenna will tighten the joint after use. 6、Radiation Exposure Statement This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. This device must be installed and operated with a minimum distance of 20 cm away from radiator/antenna to user body. 7、Declaration of Conformity Hereby Shanghai Rising Digital Co.,Ltd., declares that this SECD-3I5A-02display screen, SECD-5I7C-02 display
15thscreen,SECD-710F-02 display screen (Model No. SECD-3I5A-02, SECD-5I7C-02, SECD-710F-02) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Input Power:7~37 DC V, Normal 24DC V Rating Current: 0.2A Ambient Temperature ranges -20～+65℃℃ This device must be installed and operated with a minimum distance of 20 cm between the radiator and user body. Manufacture Shanghai Rising Digital Co.,Ltd. Address: No 318 ,Chuanda Road , Pudong New District, Shanghai,China 8、FCC Statement FCC identification number is not visible when the device is installed inside another device, then the outside of the device into which
16ththe device is installed must also display a label referring to the enclosed device. This exterior label can use wording such as the following: “FCC ID: 2AJONSECD-3I5A-02” This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. The radios in this device have been designed and manufactured to not exceed stipulated emission limits for exposure to radio frequency (RF) energy as required by the Federal Communications Commission of the U.S. Government 47 C.F.R. § 2.1091 and
17th2.1093. The antennas should be put up by the professional parts who take full responsibility for compliance with FCC15.203

Navigation menu