Riso Kagaku RFR6 RFID Tag Reader/Writer User Manual

Riso Kagaku Corporation RFID Tag Reader/Writer Users Manual

Users Manual

1RF-MODULE-V6 (Model: 050-34901) User’s Manual Ver. 1.0 Riso Kagaku Corporation
2This manual describes the use, the functions and the performance of the Radio Frequency Identification System RF-MODULE-V6(Model: 050-34901). The system is so manufactured that it can not be repaired or replaced by the user; and therefore, if there are such needs, please contact Riso Kagaku Corporation or its agent. No service work should be started before the service person has read this manual. Features This product uses radio frequency of 13.56 MHz to communicate with the tags or cards; thus, it should conform to any relative laws and regulations of the country or the region. Cautions 1. Use or store this product on the temperature and humidity conditions mentioned below, so as to maintain its operational reliability. 2. Use or store this product in an environment free of explosive gases, inflammable gases, corrosive gases, oils, organic solvents, dust, salt and metal powders. 3. Keep this product free of direct shock, strong vibration or sunshine. 4. To communicate with the tags or cards, this product uses 13.56 MHz radio frequency, which may be interfered by radio waves (noises) emitted from a transceiver, a motor, a monitor, a power supply (including a power supply IC), etc. Please make sure that such interferences will not occur before using the product in a place near to these devices. 5. Take proper measures to avoid any possible electrostatic discharge to the product, which may damage the product. 6. After doing the wiring, make sure the connectors are fastened properly. Warning Do not alter any part of the product. Alteration of the printed wiring board, the antennas or the connecting cables of the module may damage the control board of the printer, and is an illegal act if it causes the modular transmitter emissions out of the limits provided by laws or regulations.
3Specifications Dimensions Less than φ32mm×18mm Transmitting Frequency 13.56 MHz Transmission field strength Less than 500 µV/m at 3m Operating Temperature 0 to +40 oC Storage Temperature -20 to +60 oC Operating Humidity 25 to 85% RH (Without condensation) Supply voltage 5 V dc +/- 10% Discarding the Product The product should be discarded as normal printed wiring boards. If you do not know how such boards should be discarded, ask Riso Kagaku Corporation, its agent or the government. Pin Assignments PIN No. Description 1 RUN Module running signal (VIH:2.66V(min),VIL:0.66V(max))HI ACTIVE 2 /RESET Device Reset. (VIH:2.66V(min),VIL:0.66V(max))LO ACTIVE 3 RXD Recirve data (HOST to MODULE) (VIH:2.66V(min),VIL:0.66V(max)) 4 TXD Transfar data (Module to HOST) (VIH:2.66V(min),VIL:0.66V(max)) 5 GND Ground. 6 VCC +5V DC±5%(4.5V – 5.5V) Connector: BM06B-SRSS-TBT-LF-SN（JST） Connecting
4 Host Interface Protocol: ASYNC(3.3V CMOS ) Baud rate:38400bps Data length:8 bit Parity : None Stop bit: 1 bit Hnad Shaking: None Voltage level : CMOS (VIH:2.66V(min),VIL:0.66V(max)) Sample Application 1) "UIDRD" on desktop is double-clicked. Double click 2) The execution screen is displayed.
53) When "UIDREAD" button is pushed, UID of tag is read. Push Notice about the law and the standard FCC ID: RPARFR6 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that unauthorized changes or modifications not approved could void the user's authority to operate the equipment. IC: 4819A-RFR6 Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Display Reading Data Display UID Data

Navigation menu