Ritron RIT18-456 UHF-FM CALLBOX TRANSCEIVER User Manual rqx456 UserMan

Ritron Inc UHF-FM CALLBOX TRANSCEIVER rqx456 UserMan

USERS MANUAL

Rqx456_UserMan.pdf iiTYPE OF EXHIBIT: INSTALLATION AND OPERATING INSTRUCTION MANUALFCC PART: 2.1033 (c)(3)MANUFACTURER: RITRON, INC.505 West Carmel DriveCarmel, IN 46032FCC ID: AIERIT18-456MODELS: RQX-456, RQX-456-XTDATE: February 16, 2004IC STANDARDS: RSP-100, Issue 8, Section 7.2(b)INDUSTRY CANADA: 1084A-RIT18456MODELS: RQX-456-CANADA, RQX-456-XT-CANADAIncluded in this exhibit is a draft of the User Manual for the RITRON Models RQX-456 and RQX-456-XPUHF-FM Transceiver. A copy of this manual will be included with every radio.This manual provides the end user with installation and operating instructions.Signed: Michael A. Pickard - Project Engineer
OUTPOST Wireless CallboxBasic Owner’s ManualRitron Pub. 14500042 Rev. A 01/04Copyright 2004 RITRON, INC. – ALL RIGHTS RESERVEDRITRON, PATRIOT, JOBCOM, Quick Assist, and Quiet Call are registered trademarks ofRITRON, INC. OUTPOST and Quick Talk are trademarks of RITRON, INC.P.O. Box 1998, Carmel, IN 46082-1998 •••• 505 W. Carmel Dr., Carmel, IN 46032 •••• USAPhone: 317-846-1201 or 800-USA-1-USA (800-872-1872) •••• FAX: 317-846-4978Web: www.radiocallbox.com •••• E-mail: ritron@ritron.com
0Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comTABLE OF CONTENTSDescription PageWHAT THIS MANUAL COVERS ........................................................................................ iiOUTPOST CALLBOX MODEL NUMBERS.........................................................................1ABOUT THE OUTPOST WIRELESS CALLBOX ................................................................1OPERATING THE OUTPOST CALLBOX ...........................................................................2OPTIONAL OUTPOST CALLBOX FEATURES ..................................................................2INSTALLATION INSTRUCTIONSFIG-1: Callbox Assembly, Controls and Connectors............................................. 3OUTPOST Installation Instructions .......................................................................4XT OUTPOST Installation Instructions..................................................................4FIG-2: XT Callbox Mounting Brackets – Vertically Installed..................................4FIG-3: XT Callbox Assembly.................................................................................5XT Gate Guard Installation Instructions ................................................................6FIG-4: Charge Jumper in Charge Position............................................................6FIG-5: XT Callbox Gate Guard Assembly with Battery Back-Up..........................7PROGRAMMINGHOW TO READOUT CURRENT RADIO PROGRAMMING .................................8HOW TO FIELD PROGRAM FREQUENCY & TONE CODES .............................9HOW TO FIELD PROGRAM 2-TONE DECODE ................................................10HOW TO FIELD PROGRAM RADIO FEATURES ..............................................11Table 1: Programmable Frequency Codes .........................................................12Table 2: Programmable QC Tone Codes............................................................13Table 3: Programmable DQC Codes ..................................................................13Table 4: Programmable 2-Tone Codes...............................................................13Table 5: Programmable Features .......................................................................13FIELD PROGRAMMING GATE GUARD ............................................................14OPTIONAL GATE GUARD PROGRAMMING ....................................................14INTERCOM (ALWAYS-ON) PROGRAMMING ...................................................15HOW TO SEAL THE ANTENNA .......................................................................................15EXPOSURE TO RADIO FREQUENCY ENERGY ............................................................16FCC LICENSE REQUIREDLicensing.............................................................................................................16Safety Standard ..................................................................................................16Service................................................................................................................16How to Obtain an FCC License ..........................................................................16RITRON Limited Warranty ................................................................................................17WHAT THIS MANUAL COVERSThis manual covers programming, operation and installation of the OUTPOST 2-Way Callbox models RQX-156,RQX-156-XT, RQX-456, and RQX-456-XT.
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 1THANK YOU FOR CHOOSING RITRONCongratulations on your purchase of the OUTPOSTCallbox.Your new radio is the culmination of RITRON’s 25years of designing, manufacturing, and supplyingreliable, professional wireless communicationproducts. Ritron wireless products will improve theoperation, safety, and profitability of any organizationby providing instant voice communications betweenemployees throughout the workplace.OUTPOST CALLBOX MODEL NUMBERSVHF MODELSRQX-156 ...............Standard VHF CallboxRQX-156-XT ........Vandal-Resistant VHF CallboxUHF MODELSRQX-456 ...............Standard UHF CallboxRQX-456-XT ........Vandal-Resistant UHF CallboxThe model number is located on the bottom of thestandard Callbox enclosure. On XT models theStandard enclose is located inside the yellow vandal-resistant box.VHF radios are designed to operate within the 12 MHzband between factory standard 150 and 162 MHz.UHF radios are designed to operate within the 20 MHzband between factory standard 450 and 470 MHz.ABOUT THE OUTPOST WIRELESS CALLBOXThe OUTPOST Callbox is a 2-way radio transceiverused to communicate directly with portable, mobileand stationary radios, or through radio repeaters.Each OUTPOST Callbox is equipped with thefollowing features:••••Field Programming. The Callbox allows you toquickly program your radio in the field without theneed for a PC programmer. Each radio can be fieldprogrammed to one of 26 VHF or 77 UHF channeltable frequencies, and one of 51 QC or 83 DQCinterference eliminator codes.••••MURS Frequencies. VHF models can beprogrammed from a list of 5 MURS frequencies thatrequire no FCC licensing in this service.••••QC (Quiet Call) interference eliminator codes.The Callbox can be programmed from a list of 51QC Sub-audible codes.••••DQC (Digital Quiet Call) interference eliminatorcodes. Each Callbox can be programmed from alist of 83 DQC Sub-audible codes.••••Battery Powered. The OUTPOST Callbox ispowered by 6 Alkaline, D-cell batteries that canoperate the radio for up to one year.••••Low battery alert. The Callbox will send a shortbeep at the end of each transmission when thebatteries approach end-of-life. This allows the userplenty of time to replace the batteries and assureuninterrupted service.••••Wide or narrow band operation. The radio can beprogrammed for wide or narrow operation byselecting from a wide variety of field programmabletable frequencies, or by PC programming.••••Companded Audio. The radio can be fieldprogrammed to enable or disable audiocompanding. Companding will compress transmitaudio before sending it, and expand receive audiobefore it is heard on the speaker to reduce thebackground noise common in radiocommunications.••••Sensor Input. Each OUTPOST has a singlesensor input that can cause the radio to send analert tone when sensor input is detected.••••“Wake-up” or “Intercom” mode operation. TheOUTPOST Callbox can operate in the standard“Wake-Up” mode, where the radio is normally offuntil the Call Button is pressed, or can beprogrammed for “Intercom” mode where the radio isalways on.Standard Callbox XT Callbox
2Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comOPERATING THE OUTPOST CALLBOXThe OUTPOST will not receive a call unless a call is1st initiated by the OUTPOST.THE OUTPOST AUTOMATICALLY SHUTS OFFWHENEVER THERE IS INACTIVITY FOR TEN (10)SECONDS.To Initiate a Call:Press and hold the ON/PTT Button on the unit, listenfor the “beep”, and begin speaking into the MIC. Forbest communication, speak as closely as possible intothe microphone. The OUTPOST has been designedfor the caller to speak into the OUTPOST Callbox froma distance of 3 feet or less.To Receive a Response:1. When you have finished speaking, release theON/PTT Button.2. Any reply will be heard through the OUTPOSTspeaker. If a reply is not received within 10seconds of releasing the ON/PTT Button, the unitsounds a low double tone and shuts offautomatically.3. To call again, press and hold the ON/PTT Buttonand begin speaking after the “beep”.Operation Notes:The OUTPOST must be powered with D-cell Alkalinebatteries ONLY, or alternatively, with an external 12VDC power supply.If there has been no activity for 10 seconds, i.e., eitherthe ON/PTT Button has not been pressed andreleased or a reply has not been received, the unitautomatically shuts OFF. The automatic shutofffeature is designed to increase battery life.OPTIONAL OUTPOST CALLBOX FEATURESThe OUTPOST Callbox has many optional featuresavailable through PC Programming.Intercom (Always-On)The OUTPOST can be PC programmed to operate asa two-way intercom. When this feature is activatedthe 10 second automatic shut-off is disabled and theCallbox will operate in a “standby” mode, allowing theCallbox to receive calls at any time.Operating the Callbox in Intercom mode significantlyincreases the battery drain, and is therefore notrecommended for battery powered applications. Referto “External 12 VDC Power Supply” in the Installationsection of this manual. If battery powered operationis required, battery drain can be reduced with the“Battery Saver” feature detailed in this section.Battery SaverWhen the Outpost Callbox is programmed to operatein Intercom (Always-On) mode, Battery Saver canincrease battery life in both internal or external batterypowered applications.With Battery Saver activated, the Callbox willperiodically “wake-up” and listen for a received signalbefore returning to a low current “sleep” state. Thetime between “wake-up’ states can be PCprogrammed between 1-255 seconds. A longer timebetween “Wake-up” states will result in increasedbattery life.The Callbox immediately leaves Battery Saver modeany time the ON/PTT Button is pressed or a signal isreceived, and will not return to Battery Saver until the10 second inactivity timer has expired.Inactivity TimerSet from the factory for 10 seconds, the inactivity timercan be PC programmed for 1-255 seconds. A shorterinactivity time will result in increased battery life. Instandard “Wake-Up” operation a longer inactivity timerwill allow more time for a response before the Callboxturns off.Switch OutputThe OUTPOST Callbox can be PC programmed toopen and close the Switch Output whenever a unique2-tone code is received. The switch output is a simplecontact closure that may be used to open and close agate, switch on a light, sound an alarm or any otherapplication where an ON/OFF switch is required.The Callbox can be field or PC programmed toalternately open and close the switch using a single 2-tone code, or can be PC programmed for unique openand close 2-tone codes. Field programming offersnine 2-tone codes that correspond to fieldprogrammable 2-tone codes available in selectRITRON portable and base radios.Sensor InputThe Callbox can be PC programmed to send awarning tone when a change in the Sensor Input isdetected. The Sensor Input can be set to respond toan open or closed switch.Response ToneThe OUTPOST Callbox can be PC programmed tosend a unique Response tone after it receives a signalto indicate the current status of the Switch Output orthe Sensor Input.Battery Back-Up AlertIn installations with an external 12 VDC power supplyand internal battery back-up, the OUTPOST can bePC programmed to send an alert tone at the end ofeach transmission when the unit is operating on theback-up battery.Busy Channel TX InhibitWhen a user is transmitting on your radio frequencywithout your tone, you will not be allowed to transmit.The radio will beep a series of long, low tones whilethe ON/PTT button is held down (like a busy signal).
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 3CALLBOX CONTROLS AND CONNECTORSAntenna ConnectorThe antenna radiates radio signals. Before using theOUTPOST Callbox, make sure the antenna issecurely fastened into the 50Ω BNC antennaconnector. If the Outpost is to be used outdoors, seepage 15 for instructions on properly sealing theantenna connector.RF Mating ConnectorsAn internal cable fron the antenna connector isterminated into a phono style conector for connectionto the radio circuit board.Captive Plastic Case ScrewsA captive plastic case screw is located in each cornerof the case front. These 4 screws are used to securethe case front containing the radio, to the case backthat contains the batteries.Charge JumperThe charge jumper can be set to trickle charge re-chargeable backup batteries.+12 VDC InputTwo screw terminal style connectors are used for the“+” and “-“ connection of an external +12 VDC input forinstallation without batteries.Sensor InputTwo screw terminal style connectors are used for the“+” and “-“ connection of an external DC level sensor.Switch OutputTwo screw terminal style connectors are used for the“+” and “-“ connections of a 5A switch closure output.Speaker ConnectorThe internal speaker is connected to the radio printedcircuit board with a polarized connector.On/PTT ConnectorThe On/PTT switch is connected to the radio printedcircuit board with a polarized connector.Pre-Drilled Mounting HolesMounting holes located in the 4 corners of the caseback are pre-drilled for mounting to a plate, wall orpost. Once mounted, the case front is secured to thecase back through these same threaded holes.Program Cable ConnectorAn RJ11 style connector is used to connect the cablefrom the PC programmer to the radio.Program ButtonA small, momentary pushbutton is used for fieldprogramming the OUTPOST Callbox.Program DisplayA single digit LED display is used for fieldprogramming the radio.Battery HolderThe battery holder inside the case back is used for theinstallation of 6 D-cell alkaline batteries. Refer to thediagram below, or the labels beneath the cells, forcorrect installation of the batteries.Battery Mating ConnectorsPolarized, 2-pin mating connectors are used toconnect the batteries to the radio circuit board.+-+-+12 VDC InputSensor Input+-Switch OutputRF Mating Connectors50ΩΩΩΩ Antenna ConnectorCaptive Plastic CaseScrews (4 Corners)Program ButtonProgram DisplayBattery MatingConnectorsProgram Cable ConnectorBattery Holder withD-Cell BatteriesInstalledPre-Drilled MountingHoles (4 Corners)FIG-1: Callbox Assembly, Controls and ConnectorsCharge JumperSpeaker ConnectorOn/PTT Connector
4Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comOUTPOST INSTALLATION INSTRUCTIONSThe OUTPOST can be mounted to virtually anysurface with four (4) #6 panhead screws. Choose atype of screw thread and screw length which will holdfirmly in the surface to which the unit will be mounted.To MOUNT the OUTPOST: (Refer to FIG-1)1. Loosen the (4) captive screws in the front cornersof the case and separate the case front from thecase back. These screws are captive to thehousing; to prevent damaging them, DO NOTremove the screws from the housing.2. Install 6 D-cell alkaline batteries into the batteryholder. Refer to FIG-1, or the labels beneath thecells, for correct installation of the batteries.3. If required, program the radio. Refer to theprogramming section of this manual for details.4. Disconnect the RF mating connectors and thebattery mating connectors. Set the case frontcontaining the radio circuit board aside.5. Insert a #6 panhead screw into each of the four(4) corner holes in the OUTPOST case back.Position the case back in the chosen installationlocation and secure it in place with the fourscrews.CAUTIONDo not drill or penetrate the OUTPOST casewith any additional holes. Use only the pre-drilled mounting holes.6. Re-connect the RF mating connectors and thebattery mating connectors between the case frontand case back.7. Fasten the case front to the case back with thefour( 4) captive screws. Do not over-tighten theplastic screws to prevent damage.8. Insert, rotate and lock the antenna onto theantenna connector. Orient the antenna vertically.9. If the OUTPOST is to be used outdoors, it isimperative that the antenna connector be sealedwith sealing tape after the antenna has beeninstalled. Use Grainger #2A-459, Radio Shack#278-1647, or equivalent. Refer to “Sealing theAntenna” instructions in this manual.10. To install the message placard, align the center ofthe hole over the ON/PTT Button, and themushroom-head fastener strips on the back of theplacard with the strips on the front of the Outpostcase. Press firmly to interlock the strips,snapping the panel into position.CoverageDepending on the unit location and installation,the OUTPOST can cover up to 1 mile. Toincrease range, use an external antenna that ismounted higher. See the RAM-1545 MagnetMounted Antenna on page ii.XT OUTPOST INSTALLATION INSTRUCTIONSThe XT OUTPOST can be mounted to virtually anysurface with four (4) ¼” diameter fastners. Choose atype of screw thread and screw length which will holdfirmly in the surface to which the unit will be mounted.To MOUNT the XT OUTPOST: ( Refer to FIG-3)1. Remove the front faceplate from the XT Callbox.The faceplate is secured to the case with 4vandal-resistant buttonhead, Torx screws. Usethe T-25 Torx bit included with the radio toremove these screws.2. Remove the “Mounting Bracket” kit secured to theinside of the XT Callbox case.3. Loosen the (4) captive screws in the front cornersof the internal Callbox case and separate thecase front from the case back. These screws arecaptive to the housing; to prevent damaging them,DO NOT remove the screws from the housing.4. Install 6 D-cell alkaline batteries into the batteryholder. Refer to FIG-2, or the labels beneath thecells, for correct installation of the batteries.5. If required, program the radio. Refer to theprogramming section of this manual for details.6. Fasten the internal case front to the case backwith the four( 4) captive screws. Do not over-tighten the plastic screws to prevent damage.7. Re-fasten the front faceplate to the radio with the4 buttonhead Torx screws.8. Install the 4 mounting brackets to the back of theXT Callbox case as shown in FIG-3 below withthe #10-32 bolts provided. The mountingbrackets can be installed vertically, as shown, orhorizontally.9. Position the XT Callbox in the chosen installationlocation and secure it in place with four screwsthrough the mounting brackets.FIG-2: XT Callbox Mounting Brackets– Vertically Installed
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 5Battery Holder withD-Cell Batteries InstalledInternal AntennaRF MatingConnectorsON/PTT MatingConnectorsBattery MatingConnectorsON/PTT SwitchThreaded Inserts for Front PlateMounting (4 Corners)Front Plate(Bottom Edge)Captive PlasticCase Screws (4 Corners)FIG 3: XT Callbox Assembly
6Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comXT GATE GUARD INSTALLATIONINSTRUCTIONSThe XT OUTPOST GATE GUARD can be mounted tovirtually any surface with four (4) #6 panhead screws.Choose a type of screw thread and screw lengthwhich will hold firmly in the surface to which the unitwill be mounted.To MOUNT the XT OUTPOST GATE GUARD: ( Referto FIG-5)1. Remove the front faceplate from the XT Callbox.The faceplate is secured to the case with 4vandal-resistant buttonhead, Torx screws. Usethe T-25 Torx bit included with the radio toremove these screws.2. Remove the “Mounting Bracket” kit secured to theinside of the XT Callbox case.Due to the wide variety of installation possibilities,RIITRON does not provide the cables orhardware required to bring external connectionsinto the XT Callbox. When selecting your cablehardware be sure it will adequately seal the cableto the case.3. Carefully study the internal construction of the XTCallbox and determine the location on the outsidecase where the external supply and Gate Guardhook-up will be brought in. Consider clearancewith your desired hardware.4. Remove the 4 flathead screws securing theinternal mounting plate and remove entire internalcase assembly. The front faceplate will beattached to the internal case assembly, handlewith care.5. Drill the hole in the XT Callbox case required foryour cable installation.6. Install the 4 mounting brackets to the back of theXT Callbox case shown in FIG-2. The mountingbrackets can be installed vertically, as shown, orhorizontally.7. Thread your external hookup cable through thehole with approximately 6 inches of cable insidethe case. Your external cable will be connectedto the XT Callbox 6-conductor interface cable withwirenuts, dress your external wires accordingly.With your selected hardware, secure and seal thecable to the XT Callbox case.8. Position the XT Callbox case in the choseninstallation location and secure it in place withfour screws through the mounting brackets.9. If programming is required, loosen the (4) captivescrews in the front corners of the internal Callboxcase and separate the case front from the caseback. These screws are captive to the housing;to prevent damaging them, DO NOT remove thescrews from the housing.10. Program the radio, if required. Refer to theprogramming section of this manual for details.To program the radio you must first apply+12VDC external power, or install a chargedback-up battery. Refer to FIG-1 for hookup of anexternal +12VDC supply.11. If rechargeable NiCd batteries are used forbattery backup the “Charge Jumper” must beplaced into the “charge” position as shown. ! ! CAUTION ! !If rechargeable batteries are NOT used for batterybackup, be sure the “Charge Jumper” is NOT inthe “charge position. Charging alkaline batterieswill damage the cells and reduce battery life!12. Fasten the internal case front to the case backwith the four( 4) captive screws. Do not over-tighten the plastic screws to prevent damage.13. Secure the internal case assembly to the XTCallbox with the 4 flathead screws through theinternal mounting plate. Refer to FIG-5 for correctorientation and location of the antenna andcables. The front faceplate is attached to theinternal case assembly, handle with care.14. Re-fasten the front faceplate to the radio with the4 buttonhead Torx screws.ChargeFIG-4: Charge Jumper in Charge Position
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 76-ConductorInterface CableBattery Holder withD-Cell Batteries InstalledInternal AntennaThreaded Inserts for FaceplateMounting (4 Corners)RF MatingConnectorsCaptive PlasticCase Screws (4 Corners)Back-up BatteryMating ConnectorsON/PTT SwitchFaceplate(Bottom Edge)RedBlackWhiteBrownBlueGreenFIG 5: XT Callbox Gate Guard Assembly with Battery BackupChargeJumperFlathead Screws for InternalMounting Plate (4 Corners)
8Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comHOW TO READOUT CURRENT RADIO PROGRAMMING1. Loosen the (4) captive screws in the front corners of the case. These screws are captive to the housing; toprevent damaging them, DO NOT remove the screws from the housing.2. Separate the case front from the case back, leaving the battery connected to the radio. Make sure the unithas batteries installed. NOTE: The voltage of the batteries must be greater than 6 VDC to program properly.3. Press and release the ON/TRANSMIT button on the front of the Callbox to turn the radio on.4. Press and release the Program button (See FIG-1 on page 3 for location). The radio will begin to display aseries of four digits; with each digit separated by a hyphen.5. Write down the four digits. The first two digits indicate the frequency code and the last two digits the tonecode; see Table 1 and Table 2 on pages 12 and 13. In this example an RQX-456 is programmed tooperate on the “Brown Dot” frequency of 464.500 MHz (Frequency code “04”) with 100.0 Hz tone (Tone code“12”).6. If a 5th digit is displayed, the channel has been programmed for DQC and the last three digits indicate theDQC code; see Table 3 on page 13. In this example an RQX-456 was programmed to operate on the“Brown Dot” frequency of 464.500 MHz (Frequency code “04”) with a DQC code of “723”).7. If more than 5 digits are displayed, the radio has been programmed for 2-Tone Paging Decode. Thefrequency and tone codes will be displayed, followed by a “C”, then the radio will display the 2-Tone pagingcode; see Table 4 on page 13. In this example an RQX-456 was programmed to operate on the “BrownDot” frequency of 464.500 MHz (Frequency code “04”) with 100.0 Hz tone (Tone code “12”) and 2-tonepaging decode frequencies of 330.5 Hz and 569.1 Hz (2-Tone code “91”)8. If the channel is PC-programmed with any frequency or tone not listed in Table 1, Table 2 or Table 3 onpages 12 and 13, the radio will sound the error tone on contents read out and display an "E".9. Normal radio operation resumes after the programming information has been displayed.FREQUENCY CODE DQC CODEFREQUENCY CODE TONE CODEFREQUENCY CODE TONE CODE PAGING CODE
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 90412HOW TO FIELD PROGRAM FREQUENCY AND TONE CODESTo match other radios, the owner can select Frequency, Tone and DQC Codes from Table 1, Table 2 and Table 3on pages 12 and 13. In our example we will program an RQX-456 to operate on the "Brown Dot" frequency of464.500 MHz with 100.0 Hz tone.1. Refer to Table 1 on page 12 to determine the two-digit frequency code and write it down.2. Refer to Table 2 on page 13 to determine the two-digit tone code for 100.0 Hz and writeit down.3. Loosen the (4) captive screws in the front corners of the case. These screws are captiveto the housing; to prevent damaging them, DO NOT remove the screws from thehousing.4. Separate the case front from the case back, leaving the battery connected to the radio.Make sure the unit has batteries installed.NOTE: The voltage of the batteries must be greater than 6 VDC to program properly.5. Press and release the ON/TRANSMIT button on the front of the unit to turn the radio on.6. Press and hold the Program Button (See FIG-1 on page 3 for location). A "P" will appearon the program display as you enter program mode and the radio will start beep rapidly.7. Release the program button after the beeping has stopped. The radio will display aseries of six characters for Radio Identification, with each character separated by ahyphen.The 1st two characters indicate the model number, the 3rd and 4th characters indicate theradio type, and the 5th and 6th characters indicate the firmware revision.MODEL NUMBER RADIO TYPE FIRMWARE REVISION8. After the Radio Identification has been displayed the radio will emit a triple beepindicating that the radio is in program mode.9. Enter the 1st digit of the frequency code by clicking the PTT button until the programdisplay shows the desired number. Pause—the radio will sound a low tone and show ahyphen across the center of the display to indicate that it is ready to accept the next digit.10. Enter the 2nd digit of the frequency code by clicking the PTT button until the programdisplay shows the desired number. Pause—the radio sounds a low tone and will show ahyphen across the center of the display to indicate that it is ready to accept the next digit.11. Enter the 1st digit of the tone code (or 1st digit of the DQC code) by clicking the PTTbutton until the program display shows the desired number. Pause—the radio sounds alow tone and will show a hyphen across the center of the display to indicate that it isready to accept the next digit.12. Enter the 2nd digit of the tone code (or 2nd digit of the DQC code) by clicking the PTTbutton until the program display shows the desired number. Pause—the radio sounds alow tone and will show a hyphen across the center of the display to indicate that it isready to accept the next digit.13. FOR DQC CODES ONLY – Enter the 3rd digit of the DQC code by clicking the PTTbutton until the program display shows the desired number. Pause—the radio sounds alow tone and will show a hyphen across the center of the display to indicate that it isready to accept the next digit.14. Press and release the ON/TRANSMIT button to save your programming. A triple beepwill sound to indicate that programming was successful and the radio will turn off.NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" willappear on the display and the radio will turn off. Check the digits you are attempting toenter, then start over.15. Turn the radio back on for normal operation.
10 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com94HOW TO FIELD PROGRAM 2-TONE DECODEFor special applications, it is desirable to program the Callbox for 2-Tone decode operation. The user is able tofield program the radio for one of the 9 pre-determined tone pairs specified in Table 4 on page 13. These tonepairs correspond to field programmable 2-Tone encode codes available in other RITRON portable and baseradios. In our example we will program an RQX-456 to operate with 2-Tone decode frequencies of 389.0 and669.9 Hz.NOTE: Field programming frequency and tone codes will remove all 2-Tone programming. If 2-Tone operation isrequired, the 2-tone code must be re-programmed after field programming of the frequency and tone codes.1. Refer to Table 4 on page 13 to determine the two-digit code for 2-tone decode on 389.0and 669.9 Hz and write it down.2. Loosen the (4) captive screws in the front corners of the case. These screws are captiveto the housing; to prevent damaging them, DO NOT remove the screws from thehousing.3. Separate the case front from the case back, leaving the battery connected to the radio.Make sure the unit has batteries installed.NOTE: The voltage of the batteries must be greater than 6 VDC to program properly.4. Press and release the ON/TRANSMIT button on the front of the unit to turn the radio on.5. Press and hold the Program Button (See FIG-1 on page 3 for location). A "P" will appearon the program display as you enter program mode and the radio will start beep rapidly.6. Release the program button after the beeping has stopped. The radio will display aseries of six characters for Radio Identification, with each character separated by ahyphen.The 1st two characters indicate the model number, the 3rd and 4th characters indicate theradio type, and the 5th and 6th characters indicate the firmware revision.MODEL NUMBER RADIO TYPE FIRMWARE REVISION7. After the Radio Identification has been displayed the radio will emit a triple beepindicating that the radio is in program mode.8. Enter the 1st digit of the 2-Tone code by clicking the PTT button until the program displayshows the desired number. Pause—the radio will sound a low tone and show a hyphenacross the center of the display to indicate that it is ready to accept the next digit.9. Enter the 2nd digit of the 2-Tone code by clicking the PTT button until the program displayshows the desired number. Pause—the radio sounds a low tone and will show ahyphen across the center of the display to indicate that it is ready to accept the next digit.10. Press and release the ON/TRANSMIT button to save your programming. A triple beepwill sound to indicate that programming was successful and the radio will turn off.NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" willappear on the display and the radio will turn off. Check the digits you are attempting toenter, then start over.11. Turn the radio back on for normal operation.
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 115HOW TO FIELD PROGRAM RADIO FEATURESThe OUTPOST Callbox can be field programmed for a number of features that include companding, Gate Guard,and speaker volume level. Refer to Table 5 on page 13 for the single digit codes available for field programming.In our example we will program an RQX-456 for Gate Guard operation.NOTE: Field programming frequency and tone codes will turn companding and Gate Guard OFF. If compandingor Gate Guard operation is required, the single-digit Radio Feature code must be re-programmed after fieldprogramming of the frequency and tone codes.1. Refer to Table 5 on page 13 to determine the single-digit code used to enable GateGuard.2. Loosen the (4) captive screws in the front corners of the case. These screws are captiveto the housing; to prevent damaging them, DO NOT remove the screws from thehousing.3. Separate the case front from the case back, leaving the battery connected to the radio.Make sure the unit has batteries installed.NOTE: The voltage of the batteries must be greater than 6 VDC to program properly.4. Press and release the ON/TRANSMIT button on the front of the unit to turn the radio on.5. Press and hold the Program Button (See FIG-1 on page 3 for location). A "P" will appearon the program display as you enter program mode and the radio will start beep rapidly.6. Release the program button after the beeping has stopped. The radio will display aseries of six characters for Radio Identification, with each character separated by ahyphen.The 1st two characters indicate the model number, the 3rd and 4th characters indicate theradio type, and the 5th and 6th characters indicate the firmware revision.MODEL NUMBER RADIO TYPE FIRMWARE REVISION7. After the Radio Identification has been displayed the radio will emit a triple beepindicating that the radio is in program mode.8. Enter the single-digit code by clicking the PTT button until the program display shows thedesired number. Pause—the radio will sound a low tone and show a hyphen across thecenter of the display to indicate that it is ready to accept the next digit.9. Press and release the ON/TRANSMIT button to save your programming. A triple beepwill sound to indicate that programming was successful and the radio will turn off.NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" willappear on the display and the radio will turn off. Check the digits you are attempting toenter, then start over.10. Turn the radio back on for normal operation.
12 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comTABLE 1: PROGRAMMABLE FREQUENCY CODESUHF Business BandCode Frequency Color Dot Bandwidth01 467.7625 J 2502 467.8125 K 2503 464.5500 Yellow Dot 2504 464.5000 Brown Dot 2505 467.8500 Silver Star 2506 467.8750 Gold Star 2507 467.9000 Red Star 2508 467.9250 Blue Star 2509 469.2625 2510 462.5750 White Dot 2511 462.6250 Black Dot 2512 462.6750 Orange Dot 2513 464.3250 2514 464.8250 2515 469.5000 2516 469.5500 2517 463.2625 2518 464.9125 2519 464.6000 2520 464.7000 2521 462.7250 2522 464.5000 Brown Dot 12.523 464.5500 Yellow Dot 12.524 467.7625 J 12.525 467.8125 K 12.526 467.8500 Silver Star 12.527 467.8750 Gold Star 12.528 467.9000 Red Star 12.529 467.9250 Blue Star 12.530 461.0375 12.531 461.0625 12.532 461.0875 12.533 461.1125 12.534 461.1375 12.535 461.1625 12.536 461.1875 12.537 461.2125 12.538 461.2375 12.539 461.2625 12.540 461.2875 12.541 461.3125 12.542 461.3375 12.543 461.3625 12.544 462.7625 12.545 462.7875 12.546 462.8125 12.547 462.8375 12.548 462.8625 12.549 462.8875 12.550 462.9125 12.551 464.4875 12.552 464.5125 12.553 464.5375 12.554 464.5625 12.555 466.0375 12.556 466.0625 12.557 466.0875 12.558 466.1125 12.559 466.1375 12.560 466.1625 12.561 466.1875 12.562 466.2125 12.5UHF Business Band (continued)Code Frequency Color Dot Bandwidth63 466.2375 12.564 466.2625 12.565 466.2875 12.566 466.3125 12.567 466.3375 12.568 466.3625 12.569 467.7875 12.570 467.8375 12.571 467.8625 12.572 467.8875 12.573 467.9125 12.574 469.4875 12.575 469.5125 12.576 469.5375 12.577 469.5625 12.500 DELETE CODE*UHF Business Band – Canada ModelsCode Frequency Color Dot Bandwidth01 458.6625 2502 469.2625 2500 DELETE CODE*VHF Business BandCode Frequency Color Dot Bandwidth03 151.6250 Red Dot 2504 151.9550 Purple Dot 2505 151.9250 2506 154.5400 2507 154.5150 2508 154.6550 2509 151.6850 2510 151.7150 2511 151.7750 2512 151.8050 2513 151.8350 2514 151.8950 2515 154.4900 2516 151.6550 2517 151.7450 2518 151.8650 2524 151.7000 12.525 151.7600 12.526 152.7000 2500 DELETE CODE *VHF MURS **Code Frequency Color Dot Bandwidth01 154.6000 Green Dot 2502 154.5700 Blue Dot 2519 151.8200 MURS 12.520 151.8800 MURS 12.521 151.9400 MURS 12.522 154.6000 MURS 12.523 154.5700 MURS 12.500 DELETE CODE *
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 13TABLE 2: PROGRAMMABLE QC TONE CODESCode Frequency Code Frequency Code Frequency Code Frequency01 67.0 14 107.2 27 167.9 40 159.802 71.9 15 110.9 28 173.8 41 165.503 74.4 16 114.8 29 179.9 42 171.304 77.0 17 118.8 30 186.2 43 177.305 79.7 18 123.0 31 192.8 44 No Tone06 82.5 19 127.3 32 203.5 45 183.507 85.4 20 131.8 33 210.7 46 189.908 88.5 21 136.5 34 218.1 47 196.609 91.5 22 141.3 35 225.7 48 199.510 94.8 23 146.2 36 233.6 49 206.511 97.4 24 151.4 37 241.8 50 229.112 100.0 25 156.7 38 250.3 51 254.113 103.5 26 162.2 39 69.4 00 DeleteTABLE 3: PROGRAMMABLE DQC CODESCode Code Code Code Code Code Code Code023 072 152 244 331 423 532 662025 073 155 245 343 431 546 664026 074 156 251 346 432 565 703031 114 162 261 351 445 606 712032 115 165 263 364 464 612 723043 116 172 265 365 465 624 731047 125 174 271 371 466 627 732051 131 205 306 411 503 631 734054 132 223 311 412 506 632 743065 134 226 315 413 516 654 754071 143 243TABLE 4: PROGRAMMABLE 2-TONE CODESCode Tone 1 Tone 291 330.5 569.192 349.0 600.993 368.5 634.594 389.0 669.995 410.8 707.396 433.7 746.897 457.9 788.598 483.5 832.599 330.5 600.9TABLE 5: PROGRAMMABLE FEATURESCode Feature1 Companding ON2 Companding OFF3 Volume Level - Medium4 Volume Level - High5 Gate Guard ON6 Gate Guard OFF789NOTE: Companding will compress transmit audio before sending it, and expand receive audio before it is heardon the speaker to reduce the background noise common in radio communications. Companding is notrecommended unless all radios in the system are companded.
14 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comFIELD PROGRAMMING GATE GUARDThe XT OUTPOST can be field programmed for basicGate Guard operation, or PC programmed to suit yourunique requirements.To field program the Gate Guard:1. Program the frequency and tone codes per the“How to Field Program Frequency and ToneCodes” instructions on page 9.2. Program the 2-Tone code per the “How to FieldProgram 2-Tone Decode” instructions on page10.3. Program the Callbox for Gate Guard operationper the “How to Field Program Radio Features”instructions on page 11.The XT OUTPOST Callbox will now operate in GateGuard mode as follows:• The Callbox will be in “Wake-up” mode. TheON/PTT button must 1st be pressed as described in“Operating the OUTPOST Callbox” section on page2 before normal two-way communications can beestablished.• If the Callbox does not send or receive a signal formore than 10 seconds the Callbox will automaticallyturn off. The ON/PTT button must be pressed toturn the Callbox back on.• When the Callbox receives the correct 2-Tonesignal the Callbox Switch Output will momentarilyclose for 1 second. The Callbox will automaticallytransmit a confirmation tone after the 2-tone hasbeen decoded.OPTIONAL GATE GUARD PROGRAMMINGThe XT OUTPOST can be PC programmed tocustomize Gate Guard operation.Intercom (Always On) will leave the Callbox tuned onat all times, allowing Gate Guard operation even ifthere is no one at the Callbox. The higher currentrequirements of Intercom mode make it undesirablein battery powered installations.Battery Saver can be used to reduce battery drainwhen Intercom (Always On) operation is required ona battery powered installation. With Battery Saveractivated, the Callbox will periodically “wake-up” andlisten for a received signal before returning to a lowcurrent “sleep” state. The time between “wake-up’states can be PC programmed between 1-255seconds. A longer time between “Wake-up” stateswill result in increased battery life.Ring Tone will sound an alert tone on the Callboxspeaker, similar to a telephone ring tone, whenever2-tone has been successfully decoded. This willalert the Callbox user that the gate is being openedor closed.Inactivity Timer is set from the factory for 10seconds, but can be PC programmed for 1-255seconds. A shorter inactivity time will result inincreased battery life. In standard “Wake-Up”operation a longer inactivity timer will allow moretime for a response before the Callbox turns off.Gate Guard Latch operation allows programming ofseparate ON and OFF 2-tone codes. The Outpostwill close the Switch Output upon receiving the ONcode, and open the Switch Output upon receivingthe OFF code.If the Gate Guard Latch option is used with an ONcode only, the Switch Output will automatically turnOFF when the radio:1. is turned off as a result of the Inactivity Timer in“Wake-Up” mode or,2. goes to the low current “sleep” state in “Intercom(Always-On)” mode with battery saver enabled.When reading out the radio programming asdescribed in the “How to Readout Current RadioProgramming” section, the ON code will bedisplayed.Sensor Output can be programmed to detect a logiclevel and transmit an Alert tone when a change inlogic level is detected. Separate alert tones areused for OPEN (logic level high) and CLOSED(logic level low).Battery Back-Up Alert is used in installations with anexternal 12 VDC power supply and internal batteryback-up. The OUTPOST can be programmed tosend an alert tone at the end of each transmissionwhen the unit is operating on the back-up battery.Busy Channel TX Inhibit will not allow you totransmit when another user is already transmittingon your radio frequency without your tone. Theradio will beep a series of long, low tones while theON/PTT button is held down (like a busy signal).
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 15INTERCOM (ALWAYS-ON) PROGRAMMINGThe XT OUTPOST can be PC programmed to operateas a two-way intercom. When this feature is activatedthe automatic shut-off is disabled and the radio willremain on in a “stand-by” mode, allowing it to receivea call from another radio at any time. The highercurrent requirements of Intercom operation make itundesirable in battery powered installations.Intercom (Always On) must be set for the Callbox toremain tuned on at all times.Battery Saver can be used to reduce battery drain ona battery powered installation. With Battery Saveractivated, the Callbox will periodically “wake-up” andlisten for a received signal before returning to a lowcurrent “sleep” state. The time between “wake-up’states can be PC programmed between 1-255seconds. A longer time between “Wake-up” stateswill result in increased battery life.2-Tone Decode allows selective calling to a Callbox ina radio system where there is more than oneCallbox. When the Callbox is programmed for 2-tone decode in “Intercom (Always-On)” mode it willsound an alert tone on the Callbox speaker, similarto a telephone ring tone, whenever 2-tone has beensuccessfully decoded. This will alert any users inthe immediate area that there is an incoming call onthe Callbox.Ring Tone must be set to sound the alert tone on theCallbox speaker when 2-tone is successfullydecoded.Monitor can be set when used with 2-Tone decode toallow the Callbox to hear all radio traffic on thechannel. If Monitor is not set, the Callbox will onlyhear a broadcast after it has successfully decodedthe correct 2-tone code. Normal conversation canfollow after the 2-tone code is decoded and theradio will automatically reset back to 2-tone decodeafter 10 seconds of inactivity.Busy Channel TX Inhibit will not allow you totransmit when another user is already transmittingon your radio frequency without your tone. Theradio will beep a series of long, low tones while theON/PTT button is held down (like a busy signal).HOW TO SEAL THE ANTENNAIf the OUTPOST Callbox is to be used outdoors it isimperative that the entire antenna connection besealed with seal tape to provide proper operation andprevent voiding warranty.Seal tape can be purchased at most Industrial SupplyStores, Harware and Home Center Stores, orElectronic Supply Stores.Regarless of the antenna used, it is always best toweatherproof the antenna connection using seal tape.NOTICEFailure to follow these instructions willcause damage to the product, preventproper sealing of the enclose and willvoid the Manufacturers Warranty.Applying Seal Tape:1. Attach the antenna to the 50Ω BNC connector onthe OUTPOST Callbox enclosure.2. Begin wrapping seal tape at the base of theantenna connector such that it is sealed to theenclosure top.3. Overlap the seal tape as you tightly wrap upwardaround the connector and antenna. Continue tooverlap seal tape around the connector base,past the articulated portion of the antenna andseveral inches up the thin, shiny section of theantenna.AFB-1545Antenna beforesealingWrap tapefrom bottom,sealing toenclosure.Overlapsealing tape(1) inchbeyond therigid sectionof theantennaAFB-1545Antenna aftersealing
16 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comEXPOSURE TO RADIO FREQUENCY ENERGYRQX-456: This product generates radio frequency(RF) energy when the ON/PTT button on the front ofthe unit is depressed. This product has beenevaluated for compliance with the maximumpermissible exposure limits for RF energy at themaximum power rating of the unit when usingantennas available from RITRON.For both the AFB-1545 and RAM-1545 antennas, atthe 20 cm (7.9 inches) minimum expected separationdistance and greater, the maximum RF exposure iswell below the General Population/Uncontrolled limits.Antennas other than those available from RITRONhave not been tested for compliance and may or maynot meet the exposure limits at the distances given.Higher gain antennas are capable of generating higherfields in the strongest part of their field and would,therefore, require a greater separation from theantenna. This product is not to be used by the generalpublic in an uncontrolled environment unlesscompliance with the Uncontrolled/General Populationlimits for RF exposure can be assured.To limit exposure to RF energy to levels below thelimit, please observe the following:• Use only the antenna(s) available from RITRON forthese models. DO NOT operate the radio withoutan antenna.• Keep talk times as short and infrequent aspossible. DO NOT depress the ON/PTT buttonwhen not actually wishing to transmit. Theseradios are equipped with an internal timer to limitcontinuous transmit times.• When transmitting, make certain that the distancelimits for the particular model in use are observed.• DO NOT allow children to operate the radio.When used as directed, this series of radios isdesigned to comply with the FCC’s RF exposure limitsfor “Uncontrolled/General Population”. In addition,they are designed to comply with the followingStandards and Guidelines:• FCC OET Bulletin 65, Edition 97-01, SupplementC, Evaluating Compliance with FCC Guidelines forHuman Exposure to Radio FrequencyElectromagnetic Fields.• American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels withRespect to Human Exposure to Radio FrequencyElectromagnetic Fields, 3 kHz to 300 GHz.• American National Standards Institute (C95.3-1992), IEEE Recommended Practice for theMeasurement of Potentially HazardousElectromagnetic Fields-RF and Microwave.FCC LICENSE REQUIREDLicensingThe FCC requires the owners of the radios to obtain astation license before using them.The station licensee is responsible for ensuring thattransmitter power, frequency and deviation are withinthe limits specified by the station license. The stationlicensee is also responsible for proper operation andmaintenance of the radio equipment. This includeschecking the transmitter frequency and deviationperiodically, using appropriate methods.To get an FCC license for VHF or UHF frequencies,submit FCC application Form 600 as indicated in theblock at right. Your Ritron dealer can help you with thisprocess.Safety StandardsThe FCC (with its action in General Docket 79-144,March 13, 1985) has adopted a safety standard forhuman exposure to radio frequency electromagneticenergy emitted by FCC regulated equipment. Ritronobserves these guidelines and recommends that youdo also:• DO NOT hold the radio so that the antenna is veryclose to or touching exposed parts of the body,especially the face or eyes, while transmitting.Keep the radio vertical, four inches away whiletalking into the front panel.• DO NOT press the Push-To-Talk except when youintend to transmit.• DO NOT operate radio equipment near electricalblasting caps or in an explosive atmosphere.• DO NOT allow children to play with any radioequipment that contains a transmitting device.• Repair of Ritron products should be performed onlyby Ritron authorized personnel.ServiceFederal law prohibits you from making any internaladjustments to the transmitter, and/ or from changingtransmit frequencies unless you are specificallydesignated by the licensee.If your radio equipment fails to operate properly, oryou wish to have the radio programmed, contact yourauthorized dealer or Ritron.RITRON, INC., Repair Department505 West Carmel DriveCarmel, IN 46032 USAPhone: 317-846-1201FAX: 317-846-4978How to Obtain an FCC Radio LicenseBecause your Ritron radio operates on Private LandMobile frequencies, it is subject to the Rules andRegulations of the FCC, which requires all operatorsof these frequencies to obtain a station license before
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 17operating their equipment. Make application for yourFCC license on FCC Forms 600 and 159.To have forms and instructions faxed to you by theFCC, call the FCC Fax-On-Demand system at 202-418-0177 from your fax machine; request Document000600 & Form 159.To have Document 000600 & Form 159 mailed to you,call the FCC Forms Hotline at 800-418-FORM (800-418-3676).For help with questions concerning the licenseapplication, contact the FCC at 888-CALL-FCC (888-225-5322).You must decide which radio frequency(ies) you canoperate on before filling out your application.For help determining your frequencies, call Ritron at800-USA-1-USA (800-872-1872).
18 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.comRITRON, INC. LIMITED WARRANTYWHAT THIS WARRANTY COVERS:RITRON, INC. ("RITRON") provides the following warranty against defects in materials and/or workmanship in RITRON Radiosand Accessories under normal use and service during the applicable warranty period (as stated below). "Accessories" meansantennas, holsters, chargers, earphones, speaker/microphones and items contained in the programming andprogramming/service kits.WHAT IS COVERED FOR HOW LONG WHAT RITRON WILL DOOUTPOST Callboxes 1 year*During the first year after date of purchase,RITRON will repair or replace the defective product, at RITRON's option, parts and labor included at no charge.Accessories 90 days**After date of purchaseWHAT THIS WARRANTY DOES NOT COVER:• Any technical information provided with the covered product or any other RITRON products;• Installation, maintenance or service of the product, unless this is covered by a separate written agreement with RITRON;• Any products not furnished by RITRON which are attached or used with the covered product, or defects or damage from theuse of the covered product with equipment that is not covered (such as defects or damage from the charging or use ofbatteries other than with covered product);• Defects or damage, including broken antennas, resulting from:- misuse, abuse, improper maintenance, alteration, modification, neglect, accident or act of God,- the use of covered products other than in normal and customary manner or,- improper testing or installation;• Defects or damages from unauthorized disassembly, repair or modification, or where unauthorized disassembly, repair ormodification prevents inspection and testing necessary to validate warranty claims;• Defects or damages in which the serial number has been removed, altered or defaced.• Batteries if any of the seals are not intact.IMPORTANT: This warranty sets forth the full extent of RITRON’s express responsibilities regarding the covered products, andis given in lieu of all other express warranties. What RITRON has agreed to do above is your sole and exclusive remedy. Noperson is authorized to make any other warranty to you on behalf of RITRON. Warranties implied by state law, such as impliedwarranties of merchantability and fitness for a particular purpose, are limited to the duration of this limited warranty as it appliesto the covered product. Incidental and consequential damages are not recoverable under this warranty (this includes loss of useor time, inconvenience, business interruption, commercial loss, lost profits or savings). Some states do not allow the exclusionor limitation of incidental or consequential damages, or limitation on how long an implied warranty lasts, so the above limitationsor exclusions may not apply to you. Because each covered product system is unique, RITRON disclaims liability for range,coverage, or operation of the system as a whole under this warranty.WHO IS COVERED BY THIS WARRANTY: This warranty is given only to the purchaser or lessee of covered productswhen acquired for use, not resale. This warranty is not assignable or transferable.HOW TO GET WARRANTY SERVICE: To receive warranty service, you must deliver or send the defective product,delivery costs and insurance prepaid, within the applicable warranty period, to RITRON, INC., 505 West Carmel Drive, Carmel,Indiana 46032, Attention: Warranty Department. Please point out the nature of the defect in as much detail as you can. Youmust retain your sales or lease receipt (or other written evidence of the date of purchase) and deliver it along with the product. IfRITRON chooses to repair or replace a defective product, RITRON may replace the product or any part or component withreconditioned product, parts or components. Replacements are covered for the balance of the original applicable warrantyperiod. All replaced covered products, parts or components become RITRON’s property.RIGHTS TO SOFTWARE RETAINED : Title and all rights or licenses to patents, copyrights, trademarks and trade secretsin any RITRON software contained in covered products are and shall remain in RITRON. RITRON nevertheless grants you alimited non-exclusive, transferable right to use the RITRON software only in conjunction with covered products. No other licenseor right to the RITRON software is granted or permitted.YOUR RIGHTS UNDER STATE LAW: This warranty gives you specific legal rights, and you may also have other rightswhich vary from state to state.WHERE THIS WARRANTY IS VALID: This warranty is valid only within the United States, the District of Columbia andPuerto Rico.

Navigation menu