Rixson 2700Q (05 09) Removable Floor Closer With Plate Installation Instructions

User Manual: Rixson 2700Q Removable Floor Closer with Floor Plate Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 2

Installation Instructions

2700Q (05-09)

27Q Removable Floor Closer

With Floor Plate

3/4” Offset Pivoted – Handed

Closing speeds can be adjusted to suit local conditions and

requirements. Label on closer face designates the purpose

of each adjustment screw. Adjustments are for speed

control.

A. The Delay Action valve allows adjustment from full

open to 65° closed position. (Optional)

B. The Closing Speed valve allows adjustment from full

open to 15° on units without the Delay Action feature.

C. The Closing Speed valve allows adjustment from 65°

to 15° closed position on closers with Delay Action

feature.

D. Latch valve allows adjustment from 15° to closed

position.

E. Important: Backcheck adjustment must be adjusted to

vary resistance from light to firm at 60° of door open.

Do not use Backcheck as deadstop. This is an intensity

valve not speed control.

Before removing or installing closer, close down valve screws. When reinstalling, lock closer in hold-open position if

provided.

Closer Removal:

Closer Reinstallation:

1. Remove thru-bolts, arm cap and loosen arm locking screw.

2. Open door to hold-open or (approx.) 90° and close. (If non hold-open is being removed, insert a flat blade (10” min) screwdriver

between spindle and torque washer to prevent spindle from turning.)

3. Remove arm, shim and torque washer from spindle.

4. With door open, remove threshold.

5. Remove closer mounting screws (4) and slide closer out under door.

Reverse above procedure when reinstalling closer.

Before attaching arm, closer spindle must be in hold-open or rotated to 90°.

Non hold-open closers will require the use of a flat blade (10” min.) screwdriver

For rotating the spindle.

RIXSON FIREMARK

FRANKLIN PARK ILLINOIS

LH

S

L

O

W

L

A

T

C

H

D

E

L

A

Y

A

C

T

I

O

N

S

L

O

W

C

L

O

S

I

N

G

S

P

E

E

D

T

U

R

N

F

U

L

L

1

8

0

°

O

N

H

O

O

F

F

B

A

C

K

C

H

E

C

K

+-

RIXSON FIREMARK

FRANKLIN PARK ILLINOIS

RH

S

L

O

W

L

A

T

C

H

D

E

L

A

Y

A

C

T

I

O

N

S

L

O

W

C

L

O

S

I

N

G

S

P

E

E

D

B

A

C

K

C

H

E

C

K

+

-

This Set Screw Is On Selector Hold-open Types Only

Closer Adjustment

Closer Removal or Reinstallation

10-7/8 Floor Plate

9-13/16 Cement Case

Floor Plate

3/4

Arm

2-1/16 R.

Jamb

Bevel Edge

of Door

1/8” in 2”

3/16 R.

13/16

3/4 1/8 Min. Clearance Required

Between Door and Stop

2-1/16

1-5/16

5-3/8

6-1/8

Floor

Plate

5-7/8

Cement

Case

Drill (3) 3/8” Dia. Clearance Holes

in Door for Arm Screws.Mounting

1-1/4

Right Hand Shown

Conversion from inches to metric: inch x 25.4

Where vertical adjustment is necessary,

two (2) 1/16” thick shims are provided to be

placed between arm and torque washer.

Template

PAGE 4

T

U

R

N

F

U

L

L

1

8

0

°

CLOSED

70°

15°

D

E

L

A

Y

E

D

A

C

T

I

O

N

I

f

e

q

u

i

p

p

e

d

3/4

3/4

2-3/8

4” 1”

3 Holes for

1/4”-20 x 2-1/8” Long

Truss Head Machine Screw

1-1/4

12-1/8

2-1/4

3/4

3/4

7/16

5/8

3/4

1/4 1/4

C

L

1-1/16

45/64

23/64

3/4

13/16

WITH FLOOR PLATE

Set Cement Case 1-1/4”

Below Surface of Finished Floor

3/16

3/4

11/16

Door Mortised

5/16 Deep

for Arm

1-1/8

1/16

1/8 R.

Bevel Edge

of Door

1/8 in 2

Jamb

Holes for

1/4-20x5/8" FHMS or

#14x1-1/2" FHWS

180 Top Pivot

2

4-1/4

3-55/64

2-45/64

3/8

1-35/64

25/64

1-1/8

5”

3/4

13/16 5/16

5/16

3/4 1/4

1/8 Min.

Clearance

3/16 R.

Bevel Heel Edge of Door

1/8 in 2

4-1/4

4-5/8

3-9/16

2-1/2

1-7/16 3/8

1-15/16

5”

4-9/16

3-15/32

2-1/2

1-1/8

1-17/32

7/16

Door Leaf Jamb Leaf

13/16 5/16

1-1/8

13/16

5/16

O

F

F

H

O

O

N

Rixson Specialty Door Controls www.rixson.com

ASSA ABLOY

RIXSON®

Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2002, 2009, Yale Security Inc., an ASSA ABLOY Group company.

All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

RIXSON®

866-474-9766 Technical Department

Rixson Specialty Door Controls www.rixson.com 866-474-9766 Technical Department

PAGE 3

PAGE 2

How To Determine

Hand of Door

LH RH

Face a door swinging open away from you. If it opens to the

right, it is right hand. If it opens to the left, it is left hand.

Arm Cap

RIGHT HAND installation

Arm Locking Set Screw

5/8-18UNF x 1” LG

Installation Instructions

1. Install Closer

Door Stop

1/8” Minimum From

Face of Door to Door Stop

Right Hand Door

Spindle Position

3/4” From Face

of Door to C of Spindle

L

13/16” From Face of

Jamb to C of Spindle

L

Door

Jamb

A. Measure 13/16” out from door jamb.

B. Allow 1/8” minimum clearance from door stop to door

face. Measure door thickness. Add 3/4”.

C. Where lines meet determines center line of closer.

2. Install Cement Case in Floor

A. For floor plate application: Cement case is set 1-1/4”

below floor level.

B. Set cement case with styrofoam and closer attached in

floor and block in position.

C.

D. CEMENT CASE SHOULD BE LEVEL. Place levels per

illustration.

E.

Case should be parallel with center line of door.

Grout in cement case with closer and styrofoam

attached. Cement should not get between closer and

case.

LEVEL IN BOTH

DIRECTIONS

4. Hang Door

Top Pivot Jamb Portion

Top Pivot Door Portion

Intermediate

(Side Jamb)

Pivot

Spindle Arm

Knuckle

IMPORTANT:

Use plumb line to make

sure that center line of

top pivot pin lines up

with center line of closer

spindle.

A. Install top pivot in door per template.

B. Install top pivot in frame per template.

C. Center line of pivot should line up with center line of

closer. Use plumb line as illustrated.

D. See template for intermediate pivot. Use one pivot for

doors up to 250 lbs. Use two pivots for doors between

250 and 400 lbs.

3. Install Top Pivot & Closer Arm

1

3

1

3

CAUTION: Closer is shipped with “valve” screws down.

DO NOT FORCE VALVE DOWN.

A. Remove styrofoam and metal plate from closer.

B. Attach top pivot and closer arm to door.

C. Attach top pivot to frame.

D. Place closer in hold-open position or turn closer

spindle to 90 position.

E. Set door on closer spindle. Do not attempt to close

the door.

F. Push item 1 “top pivot pin” into place. Attach “cap”

item 3. (Illustration) CAP MUST BE TIGHTENED

SECURELY.

G. Install intermediate pivots. (See intermediate pivot

template)

H. Open Closing Speed and Latch valves

(counterclockwise) one turn. Door will then close.

I.

J. Put arm cap on arm and secure TIGHTLY with cap

screw furnished.

K. Insert spacer blocks as shown and attach floor plate.

While working door back and forth TIGHTEN ARM

LOCKING SCREW SECURELY with wrench

furnished.

2

2

Spacer Block

(Typ. Two)

Rixson Specialty Door Controls www.rixson.com 866-474-9766 Technical Department

Rixson Specialty Door Controls www.rixson.com 866-474-9766 Technical Department