Rixson Checkmate Series S 99 826, 926, 626, 726 Installation Instructions 80 9399 0102 015

User Manual: Rixson Checkmate Series - s 99-826, 99-926, 99-626, 99-726 Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 4

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9399-0102-015 (07-14)

ASSA ABLOY

RIXSON®

1

ASSA ABLOY

RIXSON®Installation Instructions

Door Holder and Releasing Device

WITH and WITHOUT

Integral Smoke Detector

An incorrectly installed or improperly

adjusted door closer can cause property

damage or personal injury. These instructions

should be followed to avoid the possibility

of misapplication or misadjustment.

CAUTION

®

Checkmate Series

99-626/99-826 (with detector)

99-726/99-926 (without detector)

Models

Hinge (Pull) Side of

Door Application

Stop (Push) Side of

Door Application

99-826

99-926

99-626

99-726

99-826 PULL SIDE

illustrated

RH – Right Hand Door

LHR – Left Hand Reverse

99-826 PULL SIDE

illustrated

LH – Left Hand Door

RHR – Right Hand Reverse

Components:

®

NOTES: - For wiring of 99-626/99-826 models, see "Checkmate "

"Wiring Instructions" No. 80-9399-0103-015 (07-14)

Push (Stop) Side

Pull (Hinge) Side

99-926 Hook-Up Box

99-826/99-926 Track

99-626/99-726 Track

99-726 Hook-Up Box

99-626 Hook-Up Box

Smoke

Detector

99-826 Hook-Up Box

Smoke

Detector

9/32” (7 mm);

3/8” (9.5 mm) dia. x

3/8” (9.5 mm) deep on

door opposite to closer

Standard

Optional

Through-bolts and

grommet-nuts

All

Preparation for Fasteners

Door or Frame

Fasteners Drill-Sizes

Self-Drilling Screw

Wood 3/16” (4.30 mm)

Pilot hole required

1/4” - 20 machine

screw Metal Drill: #7 (0.201” dia.)

Tap: 1/4” - 20

Sleeve nuts and

bolts

Hollow

Metal

9/32” (7 mm) through;

3/8” (9.5 mm) door face

opposite to closer

Aluminum

or Wood

3/8” (9.5 mm) through

Aluminum

or Metal No drill required

NOTE:

For special applications a separate door and frame

preparation template is packed with these instructions.

Use this instruction sheet for installation sequence and

closer adjustments only.

Use of an auxiliary door stop is always recommended.

Unit must be mounted on interior of building in dry

environment, maximum humidity of 95%.

See NFPA70 for wiring requirements and NFPA72 for alarm

system requirements.

99-726 PUSH SIDE

illustrated

RH – Right Hand Door

LHR – Left Hand Reverse

99-726 PUSHL SIDE

illustrated

LH – Left Hand Door

RHR – Right Hand Reverse

Hinge Edge of Door

Hinge Edge of Door

Adjusting

Rod

Arm Bracket

& Tube

Adjusting

Screw

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9399-0102-015 (07-14)

ASSA ABLOY

RIXSON®

2

2

1

Parts

3

Hinge (Pull) Side Application

Right Hand Shown

Mark and Drill Holes

Installation Sequence

19

(483)

3-5/8

(92)

A

B

7-1/4

(184) 2-1/2

(64)

C

L

Power Track

99-926

99-826

31-1/16

(788)

34-11/16

(881)

Dim. "A”

32-1/8

(816)

35-3/4

(908)

Dim. "B”

Hold Open Angle

(Between 85° and 110° only)

A

Lock into

hold-open

C Open door to

desired angle

BD

Use holes

that align

in arms

7/8 (22) Conduit

hole for concealed

wiring only

1/2

(13)

99-826 / 99-926 Series

4

Self-Drilling

Screw Wood

(see Note)

No drill required

3-16” (4.3mm)

Drill #7 (.201” dia)

Tap 1/4”-20

Metal

Fasteners Door or

Frame Drill Sizes

Preparation for Fasteners

Note: Wood doors/frames MUST have pilot

hole when using Self-Drilling Screws.

1/4”-20

machine screw

Aluminum

or Metal

3/4

(19)

1-7/16

(37)

1-1/4

(32)

A

C

After installed,

bend out tabs

to secure.

D

See Page 4 for

wiring instructions.

2

1

F

G

B

E

Solenoid wire

coiled inside

end of track

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9399-0102-015 (07-14)

ASSA ABLOY

RIXSON®

3

3

Parts

Stop (Push) Side Application

2

Mark and Drill Holes

Installation Sequence

A

D

E

Power Track

PTO

PTDO

30-9/16

(776)

34-3/16

(868)

Dim. "A”

31-11/16

(805)

35-5/16

(897)

Dim. "B”

F

See Page 4 for

wiring instructions.

B

C

99-626 / 99-726 Series

4

Hold Open Angle

(Between 85° and 110° only)

A

Lock into

hold-open

C Open door to

desired angle

BD

Use holes

that align

in arms

Self-Drilling

Screw Wood

(see Note)

No drill required

3-16” (4.3mm)

Drill #7 (.201” dia)

Tap 1/4”-20

Metal

Fasteners Door or

Frame Drill Sizes

Preparation for Fasteners

Note: Wood doors/frames MUST have pilot

hole when using Self-Drilling Screws.

1/4”-20

machine screw

Aluminum

or Metal

1

2

1

Left Hand Shown

12

(305)

3-1/8

(79)

A

B

C

L19

(486) 1

(25)

1-1/8 (29) hole

for Conduit

Bottom of Frame Stop

2-3/4

(70)

1/2

(13)

5-1/8

(130)

2-1/2

(64)

Solenoid wire

coiled inside

end of track

Copyright © 2009, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9399-0102-015 (07-14)

ASSA ABLOY

RIXSON®

4

3000 Highway 74 East • Monroe, NC 28112

Tel: (800)- 5670457-

www.r ixson.com

ASSA ABLOY

RIXSON®

99-726 / 99-926 Support Unit Wiring Diagram

(24VAC/DC Input)

99-726 / 99-926 Support Unit Wiring Diagram

(120VAC Input)

(Do not use a 120VAC 99-726 / 99-926 unit when power is

supplied from a 99-626 / 99-826 unit)

2-Pin Jumper SOL

1

2

3

4

3

2

1

24VAC/DC Circuit Board 4-Pin

Jumper

2-Pin Jumper SOL

1

2

3

4

3

2

1

120VAC Circuit Board 4-Pin

Jumper

Test Switch

Header for Solenoid

Connection

Openings for surface

wiring shown Fuse

125V / 1/2A

Terminal Strip for

Power Input Connection Test Switch

Openings for surface

or concealed wiring

Terminal Strip for

Power Input Connection

ELECTRICAL DATA

NOTES:

Maximum wire size is 14AWG.

All wiring and connections use standard wiring practice conforming with

local wiring codes.

For 99-626/99-826

Models:

Refer to Wiring Instructions

No. 80-9399-0103-015 (02-09)

for making wiring connections.

Earth

(+)

(-)

Earth

(+)

(-)

Input

Power

Input

Power

120VAC 24VAC 24VDC

Voltage

Current

120V 24V 24V

132V Max

102V Min

26.4V Max

20.4V Min

26.4V Max

20.4V Min

.036 Amps .059 Amps .074 Amps

Detector

26.4V Max

20.4V Min

0.034 Amps

24V

Header for Solenoid

Connection

Fuse

125V / 1/2A

Cont.:

increase the releasing force by turning the screw

accessible thru the end cap of the track using the

9/64” hex wrench provided.

Again, open door to the hold-open position.

Depress “Test Switch” button on the hook-up

board...door should close. If arm does not

release, see previous step.

IMPORTANT:

Remove solenoid wire from end of track before

installing track to frame. Do not pinch or crimp wire.

Once track and hook-up box are installed, solenoid

wire must be plugged into Header on circuit board

shown above.

After making all wiring connections:

Turn power to unit “ON”. (On Master (99-626 /

99-826) unit only, red LED should illuminate once

every 15 sec.).

Track’s hold open force is preset at the factory.

Open door to hold-open position. Manually pull

door out of hold-open and release...door should

close. If arm does not release from hold-open,