Rixson IS EM19U Side Jamb Pivot 3/4 Offset Handed

User Manual: Rixson Side Jamb Pivot 3/4 Offset - Handed Installation Instructions

Open the PDF directly: View PDF PDF.
Page Count: 2

Side Jamb Pivot
3/4" Offset – Handed
IS-EM19U
Notes:
1. Do not scale drawing.
2. Dimensions are given in inches (mm).
3. Pivot drilled for 1/4-20 FHMS
4. Right hand shown.
5. For hollow metal use 1/8" (3.2) shims (by Rixson)
Door: 652001
Jamb: 652003
For aluminum use 3/16" (4.8) shims (by Rixson)
Door: 652002
Jamb: 652004
6. See templates T-EM19U-A and T-EM19-HM for door and frame prep.
5/8" x
5
(127)
3/4
(19)
13/16
(20.6)
5/16
(8)
5/16
(8)
3/4
(19) 1/4
(6.4) 1/8 (3.2) Min. Clearance
3/16
(4.8)
Bevel Heel Edge
of Door 1/8" in 2"
(3.2 in 50.8)
4-5/8
(117.5)
3-9/16
(90.5)
2-1/2
(63.5)
1-15/16
(49.2)
1-7/16
(36.5)
3/8
(9.5)
Door Leaf
5/16
(7.93)
Jamb Leaf
5
(127)
4-9/16
(116)
3-7/8
(98.4)
2-1/2
(63.5)
3-15/32
(88.1)
1-17/32
(38.9)
1-1/8
(28.6)
7/16
(11.1)
13/16
(20.63)
4-1/4
(104.7)
See Note 5.
1-1/8
(28.6)
5/16
(7.93)
13/16
(20.63)
1-1/8
(28.6)
Door
Shim
Jamb
Shim
1/8 (3.2) or
3/16 (4.8)
See Note 5.
www.rixson.com
ASSA ABLOY
RIXSON®
DATE
TEMPLATE NUMBER
07-09
Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2003, 2009, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Side Jamb Pivot
3/4" Offset – Handed
IS-EM19U
EM19U Side Jamb Pivot
Handed 3/4” Offset
Installation Instructions
IMPORTANT: Prepare door and frame per instruction on reverse side.
Door must be hung before the pivot is installed. The EM-19U pivot
cannot take the downward load (weight) of the door. The door weight
must be carried by a floor closer, bottom pivot or additional M-19 or M-
190 side jamb pivots.
ALIGNMENT: To insure proper installation , the centerline of the side
jamb pivot must be in line with the centerline of the top and bottom pivot
points. See illustration.
ELECTRICAL RATINGS:
Low voltage only
Current ratings each wire: 2 amp. continuous.
s
PIVOT INSTALLATION:
NOTE: Door and jamb portion of EM-19U are
assembled in the factory. They cannot be
separated and must be installed as assembled.
Open door and connect wires on the jamb portion
to the wires in the frame. Push the wires back into
the frame as the jamb portion is set into place in
the frame mortise. Install the 5 jamb screws.
Connect the wires on the door portion to the door
wires. Push the wires back into the door as the
door portion is set into place in the door mortise.
Install 5 door screws.
Test the electrical installation for proper operation
of the wired door devices.
IMPORTANT:
Use plumb line to make
sure that center line of
top pivot pin lines up
with center line of
bottom spindle
How To Determine
Hand of Door
LH RH
Face a door swinging open away from
you. If it opens to the right, it is right hand.
If it opens to the left, it is left hand.
www.rixson.com
ASSA ABLOY
RIXSON®
DATE
TEMPLATE NUMBER
07-09
Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2003, 2009, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

Navigation menu