Rixson 0101 (07 09) Smok Chek V ISFM0101
User Manual: Rixson Smok-Chek V 0101 Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
SMOK-CHEK® V A Fire/Life Safety Holder Product Model 0101 Push Side Mounting Independent Closing Means Magnet 930105 120VAC 930106 24VAC/DC *85° thru Maximum Degree of Swing Single Point Hold Open Not for Use on Doors that will be Manually Closed on a Daily Basis Holder Assembly (includes magnet) 550100 120VAC 550101 24VAC/DC Holder Cover 550106-*(non-detectored) Push Side Arm 550136K* Screw Door Pivot Bracket 565118T689 Left Hand Shown 01844016 02344010-602 01030 06344808 02301420-602 02344010-602 02344012-602 Description 1/4-20 x 1 FLH Allen (1) Pan HD 1/4-20 x 5/8 (4) Washer (1) FLHD 1/4-20 x 1/2 (1) #14x1-1/4 PHPWS (2) 1/4-20x5/8 PHPMS (6) 1/4-20x3/4 PNHDSMS (2) General Information: Non Handed Door Hanging Means: • Standard 4”, 4-1/2”, or 5” Butt Hinges • 3/4” Offset Pivot • For other means, contact factory ISFM0101 2” Minimum head frame For frame face sizes less than 2”, contact factory Maximum reveal 3-1/2” For reveals from 3-1/2 to 7”, use arm 550789 *For hold-open from 105° - 180°, use arm 550789 Door Closing Device by others www.rixson.com Mounting Hole Locations • Right hand shown • Door hanging means: 4”, 4-1/2”, 5” Butts or 3/4” Offset Pivots • All dimensions given in inches (mm) 12-1/2 (318) 10-1/4 (260) 1-3/16 (30) 10-3/4 (273) 1-1/8 (80.6) 8-3/16 (208) 1/4-20 Machine Screw (4 Places) C L Butt Hinge or Pivot 7/8 (22) 1-1/4 (31.8) 1-11/16 (43) 7/8 (22) 3/4 (19) 7/8 (22) Dia. Hole Optional Knock Out “In Out” Wiring 14-20 Machine Screw or #14 Wood Screws (2 Places) 1-1/4 (31.8) Stop Dim. B 9-1/8 (232) 1-1/2 Stop Dim B 1/2 (12.7) 1-3/4 (44.5) 5/8 (16) 1-7/8 (47.7) Reinforcing Plates By Others 12 Ga. Min. 3-1/2 (89) Reveal Max. 4-1/16 (103) For Frame Less Than Shown On Chart Consult Factory D C Reinforcing Plates By Others 12 Ga. Min. Page 2 www.rixson.com 1-1/2 (38) C D 1/2 (12.7) 2-1/2 (63.5) 5/8 (16) 2-5/8 (67) Solid Line Represents Double Egress Frame Dotted Line Represents Standard Double Rabbeted Frame Push Side Mounting ISFM0101 1. Mounting Holder Fig 1a A. Layout & prepare screw holes. B. Remove appropriate knock out in Smok-Chek & attach 3/8” (9.5) conduit fitting. (Fig. 1a) C. Push conduit back into frame. D. Attach holder with (6) 1/4-20 x 5/8 pan HD screws – tighten securely. E. Attach arm to holder with (1) 1/4-20 x 1 FHD allen screw. (Fig. 1b) Fig. 1b CAUTION: SQUARE ON ARM MUST BE INSERTED AND TIGHTENED INTO HOLDER VERY SECURELY BEFORE ARM IS ATTACHED TO SPINDLE OF CLOSER. 2. Mounting Door Pivot Bracket Fig 2a A. Mount door bracket to door and fasten with two 1/4-20x1/2” RDH or #14x1-1/4 Pan HD screws. B. Slide bracket arm into holder arm. C. Attach arm to bracket spindle with washer and 1/4-28x1/2” FLH screws. (Fig. 2a) D. Position arm as per suggested arm settings listed in chart. (Fig. 2b) E. Assemble holder and bracket arms together with the 1/4-20x5/16” RDH screws. Door Hanging Means Fig 2b Arm Setting No. 18 1 2 3 4 8 10 12 14 16 1 4” Wide Butts 4-1/2” Wide Butts 5” Wide Butts Swing Clear 3/4” Offset Pivot Arm Settings 85°/135° 130°/180° 17 16 18 16 19 16 17 18 16 BEFORE BEGINNING WIRING, INSTALLER MUST BE GROUNDED! 3. Electrical Wiring Power Supply Field Wires should be 18ga OR as required by local code A. Connect switch – in series – with HOT lead of electromagnet. Hot Neutral Magnet Note: 120vAC draws .018 amp 24vAC/DC draws .091 amp Push Side Mounting ISFM0101 Switch Page 3 www.rixson.com 4. Making Adjustments to the Holder Fig 4a A. Closer spring force should be as low as possible. (Closer should arrive at lowest setting). B. Turn OFF Power (using ON/OFF switch). C. To set Hold Open: 1. Door should be in CLOSED position. 2. Raise or lower cam until the word “Push” is displayed from the UNDERSIDE of the unit (Fig 4a). 3. Open door to desired Hold Open position. 4. Raise or lower cam and ROTATE until pocket of cam is in position next to Roller A shown in Fig 4b 5. Release cam to re-engage teeth. 6. Turn ON power (using ON/OFF switch). 7. OPEN DOOR. Door should stay in Hold Open position–if not, repeat Steps 3 and 4. 8. Pull door OUT of Hold Open–door should close freely. 9. OPEN DOOR. If releasing force needs to be increased, turn adjusting nut IN. If lesser holding force is desired, turn nut OUT. 10. Attach holder cover. Fig 4b Hold Open Adjust Nut Trouble-Shooting Tips: 1. Turn ON power. 2. Can door swing far enough to engage hold open? Minimum opening is 85°. 3. Make sure closer is at lowest spring setting. 4. Put piece of metal against the magnet to make sure it is receiving current. 5. If not, double check wiring instructions. 6. If so, with door in closed position look up at holder mechanism. Word PUSH should be visible, if not, adjust cam. 7. Turn adjusting nut. 8. Check arm indexing. RIXSON ® ASSA ABLOY Page 4 www.rixson.com Rixson® and Smok-Chek® are registered trademarks of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2003, 2009, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc., is prohibited. Push Side Mounting ISFM0101
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.1.0 (Windows) Creator Tool : AdobePS5.dll Version 5.0.1 Modify Date : 2009:07:10 12:52:09-04:00 Create Date : 2009:07:10 12:52:09-04:00 Format : application/pdf Title : 0101 (07-09).qxd Document ID : uuid:32a87031-d1c8-48f3-ae8e-25fd04b75e43 Instance ID : uuid:2f4a0225-bf2c-4ff0-b06a-415f70321970 Page Count : 4 Creator : AdobePS5.dll Version 5.0.1EXIF Metadata provided by EXIF.tools