Rixson 0101 (07 09) Smok Chek V ISFM0101

User Manual: Rixson Smok-Chek V 0101 Installation Instructions

Open the PDF directly: View PDF .
Page Count: 4

SMOK-CHEK®V

A Fire/Life Safety Holder Product

Model 0101

Push Side Mounting

Independent Closing Means

*85° thru Maximum Degree of Swing

Single Point Hold Open

Not for Use on Doors that will be

Manually Closed on a Daily Basis

General Information:

Non Handed

Door Hanging Means:

• Standard 4”, 4-1/2”, or 5” Butt Hinges

• 3/4” Offset Pivot

• For other means, contact factory

2” Minimum head frame

For frame face sizes less than 2”, contact factory

Maximum reveal 3-1/2”

For reveals from 3-1/2 to 7”, use arm 550789

*For hold-open from 105° - 180°, use arm 550789

Door Closing Device by others

ISFM0101

Left Hand Shown

Screw

01844016

02344010-602

01030

06344808

02301420-602

02344010-602

02344012-602

Description

1/4-20 x 1 FLH Allen (1)

Pan HD 1/4-20 x 5/8 (4)

Washer (1)

FLHD 1/4-20 x 1/2 (1)

#14x1-1/4 PHPWS (2)

1/4-20x5/8 PHPMS (6)

1/4-20x3/4 PNHDSMS (2)

Holder Cover

550106-*(non-detectored)

Magnet

930105 120VAC

930106 24VAC/DC

Holder Assembly (includes magnet)

550100 120VAC

550101 24VAC/DC

www.rixson.com

Door Pivot Bracket

565118T689

Push Side Arm

550136K*

Reinforcing Plates

By Others

12 Ga. Min.

C

Reinforcing Plates

By Others

12 Ga. Min. 3-1/2 (89)

Reveal

Max.

4-1/16

(103)

D

For Frame Less Than

Shown On Chart

Consult Factory

C

1/2 (12.7)

5/8 (16)

D

2-1/2 (63.5)

2-5/8 (67)

1-1/2

(38)

Stop Dim.

1-1/4

(31.8)

C

LButt Hinge or Pivot

9-1/8

(232)

7/8

(22)

1/4-20 Machine Screw

(4 Places)

10-3/4

(273)

1-1/8

(80.6)

8-3/16

(208)

Optional Knock Out

“In Out” Wiring

1-1/4

(31.8)

10-1/4

(260)

12-1/2

(318)

7/8 (22)

Dia.

Hole

7/8

(22) 3/4

(19)

1-11/16

(43) B

Stop Dim

1/2 (12.7)

5/8 (16)

B

1-3/4 (44.5)

1-7/8 (47.7)

1-3/16

(30)

1-1/2

14-20 Machine Screw

or #14 Wood Screws

(2 Places)

Mounting Hole Locations

• Right hand shown

• Door hanging means: 4”, 4-1/2”, 5” Butts or 3/4” Offset Pivots

• All dimensions given in inches (mm)

Page 2

ISFM0101

Solid Line Represents Double Egress Frame

Dotted Line Represents Standard Double Rabbeted Frame

www.rixson.com

Push Side Mounting

Page 3

ISFM0101

1. Mounting Holder

A. Layout & prepare screw holes.

B. Remove appropriate knock out in Smok-Chek &

attach 3/8” (9.5) conduit fitting. (Fig. 1a)

C. Push conduit back into frame.

D. Attach holder with (6) 1/4-20 x 5/8 pan HD screws –

tighten securely.

E. Attach arm to holder with (1) 1/4-20 x 1 FHD allen

screw. (Fig. 1b)

CAUTION: SQUARE ON ARM MUST BE INSERTED AND TIGHTENED INTO HOLDER VERY

SECURELY BEFORE ARM IS ATTACHED TO SPINDLE OF CLOSER.

Power Supply

Magnet

Hot

Switch

Neutral

BEFORE BEGINNING WIRING, INSTALLER MUST BE GROUNDED!

3. Electrical Wiring

Field Wires should be 18ga OR as required by local code

A. Connect switch – in series – with HOT lead of

electromagnet.

Note:

120vAC draws .018 amp

24vAC/DC draws .091 amp

Fig. 1b

Fig 1a

www.rixson.com

Push Side Mounting

2. Mounting Door Pivot Bracket

A. Mount door bracket to door and fasten

with two 1/4-20x1/2” RDH or #14x1-1/4

Pan HD screws.

B. Slide bracket arm into holder arm.

C. Attach arm to bracket spindle with washer

and 1/4-28x1/2” FLH screws. (Fig. 2a)

D. Position arm as per suggested arm

settings listed in chart. (Fig. 2b)

E. Assemble holder and bracket arms

together with the 1/4-20x5/16” RDH

screws.

12 3481012 14 16 1

Fig 2a

Fig 2b

Arm Setting No. 18

Door Hanging

Means

4” Wide Butts

4-1/2” Wide Butts

5” Wide Butts

Swing Clear

3/4” Offset Pivot

Arm Settings

85°/135° 130°/180°

17 16

18 16

19 16

17 -

18 16

Rixson® and Smok-Chek® are registered trademarks of Yale Security Inc., an ASSA ABLOY Group company.

Copyright© 2003, 2009, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of Yale Security Inc., is prohibited.

4. Making Adjustments to the Holder

A. Closer spring force should be as low as possible.

(Closer should arrive at lowest setting).

B. Turn OFF Power (using ON/OFF switch).

C. To set Hold Open:

1. Door should be in CLOSED position.

2. Raise or lower cam until the word “Push” is dis-

played from the UNDERSIDE of the unit (Fig 4a).

3. Open door to desired Hold Open position.

4. Raise or lower cam and ROTATE until pocket of

cam is in position next to Roller A shown in Fig 4b

5. Release cam to re-engage teeth.

6. Turn ON power (using ON/OFF switch).

7. OPEN DOOR. Door should stay in Hold Open

position–if not, repeat Steps 3 and 4.

8. Pull door OUT of Hold Open–door should close

freely.

9. OPEN DOOR. If releasing force needs to be

increased, turn adjusting nut IN. If lesser holding

force is desired, turn nut OUT.

10. Attach holder cover.

Trouble-Shooting Tips:

1. Turn ON power.

2. Can door swing far enough to engage hold open? Minimum opening is 85°.

3. Make sure closer is at lowest spring setting.

4. Put piece of metal against the magnet to make sure it is receiving current.

5. If not, double check wiring instructions.

6. If so, with door in closed position look up at holder mechanism. Word PUSH should be visible, if

not, adjust cam.

7. Turn adjusting nut.

8. Check arm indexing.

Page 4

ISFM0101

Fig 4a

Fig 4b

Hold Open

Adjust Nut

www.rixson.com

Push Side Mounting

ASSA ABLOY

RIXSON®