Rixson MW700 Series Overhead Concealed Closer Installation Instructions IS MW70012 14
User Manual: Rixson MW700 Series Overhead Concealed Closer Installation Instructions Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
PAGE 4 RIXSON ® MW700 Series Overhead Concealed Closer (Wood Door & Metal Frame) MW700 Series, Center Hung Single Acting, Handed 6. Centering the door. Open the adjustment valves. ASSA ABLOY 800 Series Installation Instructions ISMW700 (12-14) Center door in jamb by adjusting centering screws in top arm. Tighten arm screws securely. Jamb Installation 700 Series Adjust arm centering screws to provide pressure of door against stop on frame. Tighten main arm screws securely. 1-9/16 (39.7) 1/4 (6.4) 1-3/8 (35) 17-1/2 (444.5) 2 (50.8) 1/4 (6.4) 1/2 (12.7) 9/32 (7.1) Mounting Holes 1/2 (12.7) 3-23/32 Max. Width (94.5) of Closer 45° 1-9/16 (39.7) 1-3/8 (35) 1/2 (12.7) 1-7/64 (28.2) From Bottom of Head Jamb to Top of Mounting Tabs Critical Dim. CL Spindle & Bottom Pivot 1-15/32 (37.3) Side View 1/8 (3.2) 1/2 (12.7) 1-3/8 (35) Nominal Clearance 9-1/2 (241.3) 2-3/4 (69.9) 1-1/2 (38.1) 17-1/2 (444.5) 1-3/8 (35) 800 Series 1-1/4 (31.8) #10-24 x 5/16 FHMS Cover Plate Screws (6 Places) 1/16 (1.6) Nominal Clearance Wood Door Installation 31/32 (24.6) 31/32 (24.6) 3-3/4 9-7/8 8-3/4 (250.8) (222.2) 9/32 (7.1) Dia. Holes for Adjusting Valves (2 Places) Top View (With Arm) 7/8 (22.2) 2-5/16 (58.7) 4-1/16 (103.2) Arm Pivot Pin .187 Dia. 8-3/16 (208) 13/16 (20.6) 15/32 (11.9) Dia. Hole for Centering Screws (2 Places) Vertically Adjustable Pivot Adjust this valve to increase or decrease backcheck Arm Plate Used With Arm on Wood Doors - Attach with #14 x 1-1/2" FHWS 13/16 (20.6) Top View 218 Bottom Pivot Adjust each valve screw per illustration. 3/16 (4.8) Nominal Clearance Between Bottom of Door and Finished Floor or Top Surface of Threshold Side View 3/8 (9.5) See Note 4 12-1/4 (311.2) Cutout in Top of Door Adjust this valve to increase or decrease speed of door 2-1/4* (57.2) Provide Clearance Hole for Pin 1" (25.4) 1-7/16 (36.5) To increase backcheck, turn valve clockwise, to decrease backcheck turn valve counter clockwise. RIXSON Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2007, 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. ® ASSA ABLOY 866-474-9766 Technical Department NOTES: 1. Do not scale drawing. 2. #192 Closer Mounting Channel details on Page 2. 3. Single acting operation requires a door stop on the underside of frame. 4. #199 door end cap optional extra. (mortise for top and bottom of door is identical.) 5. Door radius recommended is 2-5/8" (66.7). 6. All dimensions given in inches (mm). Rixson Side View 1/8 (3.2) Notch Heel of Door 1-1/2 (38.1) Wide 3/16* * Mortise only when end (4.8) cap specified (see Note 4). To decrease speed turn valve clockwise. To increase speed turn valve counter clockwise. www.rixson.com Max. Height of Closer (95.2) Bottom View (Cover Plate) 4-1/4 (108) Each valve controls one swing only. To decrease speed turn clockwise. To increase speed turn counter clockwise. Rixson 17-27/32 (453.2) 18-3/4 (476.3) Cover Plate 18-1/4 x 3-3/4 (463.6 x 95.3) 7. Adjust closing speed of door. 1-39/64 (40.9) 1-23/64 (34.5) Top View 31/64 (12.3) 700 Series 1-39/64 (40.9) 1-23/64 (34.5) 2-1/16 (52.4) 5-9/16 (141.3) 3-1/8 (79.4) Bottom View 1-3/8 (35) www.rixson.com 1/4-20x7/8 Hex Head Cap Arm Mounting Screws (2 Places) 1" (25.4) 1-3/8 (35) CL Width of Bottom Pivot 1-9/16 (39.7) Min. Depth of Bottom Channel End View 11/16 (17.5) 1-3/8 (35) Width of Bottom Pivot #14X1-1/2 FHPWS 866-474-9766 Technical Department 192 Hollow Metal Mounting Channel PAGE 2 This dimension to be a slip fit into inside width of head frame. Weld both end plates to mounting channel securely on sides and top. 3/16 (4.8) 1. Install mounting channel in frame. CL Spindle & Bottom Pivot 1-3/4 (44.4) 1/8 (3.2) x 45° CHMF. PAGE 3 Installation Instructions Step #2 Mounting Channel Assembly Bottom Edges Flush Step #1 Reinforcement End Plate (2 Reqd. by Others) 1-1/8 (28.6) From Face of Head Frame to Bottom of Mounting Posts Critical Dim. Bottom Edges Flush End View of Head Frame Side View of Head Frame CL Closer Spindle 2-3/4 (69.8) Weld both end plates to mounting channel securely on sides and top. 1/8" (3.2) Dia. Ref. Over Closer Spindle 18-1/4 (463.6) Cutout for Cover Plate Weld both end plates to inside of head frame. See Note 5 Underside View of Head Frame 4-5/16 (109.5) B 1/2 (12.7) Step #3 Head Frame Installation CL Closer Spindle M 3-3/4 (95.2) Cutout for Cover Plate CL Door & Mounting Channel 2-5/32 (54.8) JA 1-7/8 (47.6) 2. Install bottom pivot floor portion. (see 218 instruction sheet) Max. Width of Mounting Channel NOTES: 1. Do not scale drawing. 2. Right hand door shown. 3. Minimum width head frame 2" x 51/2" (50.8 x 139.7)16 ga. max. 4. All dimensions given in inches (mm). 5. Channel must be installed prior to jobsite installation of frame. 3. Install wood door arm plate using #14 x 1-1/2 FHWS. Install main arm using (2) 1/4 x 20 x 7/8" hex head arm screws. Drill (2) each 15/32 holes for centering screws, where shown on template. Do not tighten arm or centering screws. 4. Install door portion of bottom pivot. (see 218 instruction sheet) Included in package: DOOR Closer Mounting Channel 5. Install Door. Turn closing speed valves shut (clockwise). Closer Body a. Using a suitable wrench, turn spindle of closer to 90° OR hold open position Cover Plate b. Slide the door over the 218 pivot, which is attached to the bottom of the door frame. Making sure the door is resting on the bottom pivot, tilt the door so that the opening in the top centering bracket fits into the main spindle a the top of the door. Centering Arm c. Install arm clamp making certain that spindle and arm fit properly. Fasten with two 5/16” socket head cap screws. IMPORTANT: Tighten arm locking screws securely while working door back and forth. 218 Bottom Pivot Rixson www.rixson.com 866-474-9766 Technical Department Rixson www.rixson.com 866-474-9766 Technical Department
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Page Count : 2 Create Date : 2014:12:29 11:34:47-05:00 Modify Date : 2014:12:29 11:34:47-05:00 Producer : Corel PDF Engine Version 16.1.0.843 Author : Owner Creator : CorelDRAW X6 Title : Untitled-1EXIF Metadata provided by EXIF.tools