Robert Bosch 6LPRF 915 MHz FHSS Mesh Radio for IOT User Manual Integration Manual

Robert Bosch (Australia) Pty Ltd 915 MHz FHSS Mesh Radio for IOT Integration Manual

Integration Manual

Integration Manual MCSS RF Module By Date Signature Drawn AE-BE/EHW4-AU KU 24/01/2019 Checked AE/EBA1-AU BW 06/02/2019 Approved Contents Operation and integration instructions ................................................................................... 1 General Description ............................................................................................................. 1 Parts Affected ...................................................................................................................... 1 Features ............................................................................................................................... 1 Regulatory Information ........................................................................................................ 2 Labelling and user information requirements ................................................................. 2 RF Antennas ..................................................................................................................... 2 RF Exposure ...................................................................................................................... 3 Helpful Websites .................................................................................................................. 3 Operation and integration instructions General Description Radio frequency module encompassing two variants. This module operates as a frequency hopping system in the 915MHz band. The variants have identical RF sections and only differ in non-radio frequency parts loading with connectors and a USB to UART section. Parts Affected Model Number Part Number Interface 6LP SN F005V19473 Serial 6LP GW F005V19474 Mini PCI-E USB Features  Operating band: 902 to 928MHz  Channels used: 917 to 927.6MHz  Number of channels: 50
Integration Manual MCSS RF Module  Nominal power (radiated or conducted): 24.5dBm conducted  Modulation(s): 2GFSK 50KHz deviation  Nominal bandwidth: 100KHz  Frequency hopping transmitter  OEM installation only Regulatory Information The finished product is required to comply with all applicable FCC equipment authorisations, regulations, requirements and equipment. We will provide guidance to the host manufacturer for compliance with the FCC part 15B requirements. The OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove or install module. The module is limited to installation in mobile or fixed application. Labelling and user information requirements The end device must be labelled with the FCC ID. If the FCC identification number of the module is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Any similar wording that expresses the same meaning may be used. The user’s manual must include the following text: RF Antennas The transmitter can only be used with the following antennas:  Pulse W5012 2dBi half wave dipole connected by a 200mm Amphenol u.fl to RP-SMA cable 336314-14-0200 Contains Transmitter Module FCC ID: LXP-6LPRF or Contains FCC ID: LXP-6LPRF Warning: Any changes or modifications not expressively approved by (company name) could void the user's authority to operate this equipment THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Integration Manual MCSS RF Module Any connection used in the host system must use a unique antenna connection on the outside of the device. Recommended connection is an RP-SMA type and that is included in the module kit. Antenna location must be selected to provide at least 20 cm between itself and nearby persons. RF Exposure Calculated using MPE as the unit is designed for mobile or fixed location transmitters no SAR has been calculated/measured. The unit is designed for >20cm distance to any person when in use. The unit is designed for general population/uncontrolled exposure of S<1mW/cm^2. 𝑆 = 𝑃 ∗ 𝐺4𝜋𝑑^2 S=Power density in mW/cm^2 D=distance in cm P=power in mW G=numeric antenna gain = 2dB = 1.258 EUT output power = 310mW S=0.077584mW/cm^2 which complies with the FCC requirements. Helpful Websites  Federal Communications Commission (FCC)

Navigation menu