Roku N1001 1 x 2 Wi-Fi Module User Manual

Roku, Inc. 1 x 2 Wi-Fi Module

Contents

User Manual

PRODUCT SPECIFICATION 1 X 2 WI-FI MODULE Roku WM01 Version 1.0 Liteon PN: AAZ200001G This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized persons without the written consent of LTC. Change History: Revision Date Author Change List Version 1.0 2014/01/27 Kaysa Lee Preliminary Author: Kaysa Lee Approved by: Sunny Hsieh Editor: Kaysa Lee Project Leader: Sunny Hsieh
CONTENT PRODUCT FEATURES ....................................................................................................................3PRODUCT SPECIFICATIONS........................................................................................................3MAIN CHIPSET........................................................................................................................................3FUNCTIONAL SPECIFICATIONS ...............................................................................................................3MECHANICAL.........................................................................................................................................4PRODUCT PICTURE.................................................................................................................................4PIN DEFINITION ......................................................................................................................................5BLOCK DIAGRAM...................................................................................................................................5EEPROM INFORMATION ..............................................................................................................5ENVIRONMENTAL..........................................................................................................................5
PRODUCT FEATURES • Operate at 2.4GHz band • 150Mbps PHY Rate Support • 1T1R Modes • USB 2.0 support for date rates up to 12Mbps full speed and 480Mbps high speed • IEEE standards support: IEEE 802.11b/g and 802.11n • 802.11i- WEP 64/128, AES, TKIP • Support Wi-Fi Direct • RoHS compliance • Low Halogen compliance Product specifications Main chipset MAC/Baseband/RF: Broadcom BCM43143 Functional Specifications Standard IEEE802.11b; IEEE 802.11g; IEEE802.11n Bus Interface Universal Serial Bus (USB2.0) Data Rate 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 7 for HT20MHz Media Access Control CSMA/CA with ACK Radio Technology 802.11b: CCK, DQPSK, DBPSK 802.11g: 64QAM, 16 QAM, QPSK, BPSK 802.11n: BPSK, QPSK, 16QAM, 64QAM Network architecture Infrastructure mode Wi-Fi Direct Miracast Operating Channel 2.4-2.483 GHz:IEEE Channels 1-11 (USA) Transmit Output Power (Tolerance: +1.5dBm/-1.5dBm) 802.11b 17.5dBm 802.11g 15.5dBm@54Mbps 802.11n 15dBm Receiver Sensitivity 802.11b: Less than -76dBm 802.11g: Less than -82dBm @ 6Mpbs Less than -65dBm @54Mbps 802.11n: Less than -82dBm @ MCS0 Less than -64dBm @ MCS7
Security 64-bit, 128-bit WEP, TKIP, AES, WPA, WPA2, WPS IEEE 802.11i Operating Voltage 3.3V ±9% I/O supply voltage Power Consumption 299.62mA/381.89mA (Mean/Max) 988.746mW/1260.237mW(3.3V) Antenna Type Antenna 1: On-board metal PIFA-type antenna Antenna 2: Stand-alone metal PIFA with soldered mini-coaxial cable using male U.FL. connector *Environmental factors dependent Mechanical Product Picture Top Bottom
Pin definition Pin Number Pin Name 1 VCC(3V3) 2 D- 3 D+ 4 GND 5 NC 6 RESETn Block Diagram EEPROM INFORMATION Vendor ID 0x0A5C Product ID 0xBD1E ENVIRONMENTAL Operating Operating Temperature: 0 to 40C Relative Humidity: 5-90% (non-condensing) Storage Temperature: -40 to 80C Relevant Humidity: 5-80% (non-condensing)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Information to OEM integrator The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location. 1. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multitransmitter product transmitter product procedures.
2. Only those antennas with same type and lesser gain filed under this FCC ID number can be used with this device. 3. The regulatory label on the final system must include the statement: “Contains FCC ID: xxxx “. 4. The final system integrator must ensure there is no instruction provided in the usermanual or customer documentation indicating how to install or remove the transmitter module except such device has implemented twoways authentication between module and the host system.
IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur: “Appareils Numériques,” NMB-003 édictée par l’Industrie. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer fonctionnement du dispositif. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Afin de réduire les interférences radio potentielles pour les autres utilisateurs, le type d'antenne et son gain doivent être choisie que la puissance isotrope rayonnée équivalente (PIRE) est pas plus que celle premise pour une communication réussie. RF exposure warning: The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Avertissement d'exposition RF: L'équipement est conforme aux limites d'exposition aux RF établies pour un incontrôlés environnement. L'antenne (s) utilisée pour ce transmetteur ne doit pas être co-localisés ou fonctionner en conjonction avec toute autre antenne ou transmetteur.Avertissement d'exposition RF: 1. Cet emetteur ne doit pas n'etre coimplante ou operation en meme temps qu'aucune autre antenne ou emetteur. 2. Cet equipement est conforme aux limites d'exposition de rayonnement de la FCC rf determinees pour un environnement non controle. Cet equipement devrait etre installe et actionne avec une distance minimum de 20 centimetres entre le radiateur et votre corps. CAN ICES-3 (B)/NMB-3(B)

Navigation menu