Rosslare SA04G Panic Button Remote Control User Manual Visio SA 04 H Instruction Manual 010204 Page 1 vsd

Rosslare Enterprises Ltd Panic Button Remote Control Visio SA 04 H Instruction Manual 010204 Page 1 vsd

Contents

User Manual Part 1

Wireless Panic Button TransmitterQ: What is a Transmitter ?A: A transmitter is an electronic device thatuses RF energy and coded digital messages tocontrol and communicate commands to otherelectronic products.Q: What is SA-04 PANIC BUTTON and how can itbenefit me ?A: SA-04 allows the user to set off the securitysystem alarm with just a press of the button, whenin a dangerous situation or in need of help, throughthe Control Panel.Q: What is SUPERVISOR or SUPERVISED sensor ?A: A Supervised sensor continuously reports to thereceiver or security panel to confirm status of thesensor and its presence. If the receiver fails to hearfrom a sensor within a pre-programmed time, itwill presume a sensor is missing or malfunctioningand notify the user. This provides added security.INTRODUCTION (FAQ's) - continued;OPERATION - GENERAL NOTESThe SA-04 is a miniature radio transmitter, designedto send coded RF transmissions to wireless receiversand control panels. The transmissions are activated bydepressing the pushbutton on the unit.The SA-04 Panic Button is a new addition to theRosslare’s wireless line, used for individuals who needto feel additional protection fro their security system.The SA-04 provides immediate access to the system,causing an alarm to be announced with the push of asingle-button.MAIN FEATURES* Lightweight and easily transported with two typesmethods of carrying.* Long-range: provides security up to 100 meters fromthe base.* One-button operation: quick access in the event of anemergency.* Hermetically-sealed unit, against dust and water -perfect for all-weather use, around the premises.AND IMPORTANT INFORMATIONINSTALLATION INSTRUCTIONSP/N: 9J-REL-xxx-xxxxxxxx-xxThis product may be sold in the followingmember states of the European Community:Austria Germany NorwayBelgium Greece PortugalDenmark Holland SpainFinland Ireland SwedenFrance Italy United Kingdom!GENERAL DESCRIPTIONINTRODUCTION (FAQ's)Q: What is LOW BATTERY detection ?A: For all supervised sensors, LOW BATTERYdetection is when a sensor continuously measuresits battery state and transmits a low battery signalto the security panel when the battery's voltagedrops below a certain level. This alerts the user inadvance to replace a weak battery.Q: What is a CASE TAMPER detector?A: A Case Tamper detector monitors any unauthorizedopening of the unit housing. A signal will betransmitted to the security panel to notify the userof such tampering.Q: What is a BACK TAMPER detector ?A: Once the sensor is mounted and activated, the BackTamper detector ensures that the sensor is notremoved or vandalized by detecting any removal ofthe unit from a wall or corner. The Back tamperdetector will alert the security panel in such cases.The SA-04 remote control is activated by pressing thebuttons on the unit and transmits this information to thereceiver panel.Since the SA-04is a portable wireless device andsystem reception is dependent upon the conditions ofuse as follows:- AVOID: Placing the SA-04 near strong magnetic orelectrical fields other than the magnet with which it isintended to be used. Otherwise, performance could beaffected and false alarms could occur.- AVOID: Using near or behind large metal surfaces andmultiple concrete/steel walls. This may interfere orblock the wireless signals. Make sure to test the rangefrom the desired location by using the RF TestProcedure to ensure reception.- AVOID: Submerging in water.12 345 678 9SA-04 Instruction Manual - Version 1.0 (Page 1/1)WARRANTY10 11 12INTERNATIONAL OFFICESU.S.A.: Rosslare America Inc.Westlake, Los Angeles, CA 91632 U.S.ATel: (818) 707 2974 Fax: (818) 7070543Rosslare America Inc.2001 Reliance, Packway, Suite DBedford, Texas 76021 U.S.ATel: (817) 685 9100 Fax: (817) 685 9188Rosslare Powerpath NAPDC.North America Product Development22e. Howard St, # 238 Des Plaines, IL60018, U.S.ATel: (847) 827 6330 Fax: (847) 8276433ISRAEL Rosslare Israel Ltd (Center Office)22 Hamelacha St, PO BOX 11407, Rosh Ha-Ayin, 48091,Hong Kong: Rosslare Enterprises Ltd.905-912 Wing Fat Industrial Building12 Wang Tai Road, Kowloon Bay,Hong Kong. Tel (852) 2795 5630 Tel (852) 2795 1508www.rosslare.com.hkThe Manufacturer's warranty on this product is for a period of one year from the dateof manufacture against defects in materials and workmanship. Manufacturer'swarranty hereunder is limited to repair or replacement, at the manufacturer's soleoption, if the product is found to be defective in normal use during the warrantyperiod. The warranty is given in favor of the original purchase only. Subject to theabove warranty, manufacturer's liability and that of it's distributors, re-sellers andagents and is wholly limited to the original purchase price and no payment will bemade for related or consequential loss including but not limited to labor costs incurredin inspection, replacement or repair of defective products. This warranty is givenexpressly and in place of all other expressed or implied warranties of merchantabilityand fitness for a particular purpose and this warranty is the only warranty made by themanufacturer. No agent, representatives or employee of the manufacturer has theauthority to waive, alter or add to the printed provisions of this warranty, to makerepresentation of warranty not contained herein or to extend this warranty to anyoneother than the original purchaser of the product. The SA-01 PIR is guaranteedagainst defects in workmanship and material for a period of 12 (Twelve) months fromdate of purchase. Return the faulty product with a dated proof of purchase to yourdealer for replacement.NOTICEThe SA-04 is designed to send an electronic signal to alarm control system,should intrusion occur, the warranty does not make the manufacturer or the distributorof the SA-01 PIR held liable for consequential damages resulting from any breech ofwarranty, expressed or implied, applicable to their use.SPECIFICATIONSBattery: 3-volt Lithium 165 mAh (non-removable)CAUTION! Dispose of Properly, do not re-charge,disassemble, heat or incinerate.Operating Temp: - 10oC to + 50oC- 4oF to + 122oFOperatingHumidity: Up to 95% Non-Condensing (max.)RF Frequency: Available in 433.92 or 68.35 MHzInstallation: Worn on arm, keychain or around neck on necklaceTamper: There is no tamper on this device.Supervisor: No Supervisory signal exists with the SA-04,allowing the unit to stay on the person, evenwhen leaving the system sensory area.Current: Standby - 0 uATransmit - 15 mASize: 45mm (diameter) x 15mm (thickness)(1.77" " x 0.6 ")Weight: 28 grams ( .21 oz) with battery1) Using the installer pass code (8888) by pressing the MENU button and entering the code on the keyboard, enter the Installer Menu.You will then enter the installer programming menufor the SP-06 V control panel 43 2 5 6 7 81 OFF MENU ESCSET INSTALL CODEMASTER CODEZONEPANIC MENU ESCENTERSUPER VISION MASTER CODE USER CODE SET OUTPUT SIREN TIME EXIT DELAY CLOCK SYSTEM TEST PARTIAL OFF MODE SET SIREN SILENT PANIC ACTIVATE CHIME CODE ENTRY DELAY CLEAR R/F ADD R/F SET ZONE TELEPHONE ZONE MENUMENU88& 88 88 88ENROLLING THE SA-04 TO THE SP-06MENUESCNUMBERENTRY DELAYCLEAR R/FADD R/FSET ZONEZONEMENUESCENTERADD R/FSET ZONEZONEPANIC8ZONECLEAR R/F2) In the INSTALLER MENU, press the down arrow to select the ZONE menu and press Enter3) In the ZONE menu, when prompted for the zone number, press the number 8 to select Zone 8.& ENTERENTER& & 884) To program operation of the Panic Button Use the down arrow to select SET ZONE option and Press Enter.5) Press the SET key until the zone type shows “PANIC”, for an audible emergency alarm, to enable the SA-04 to perform a non audible alarm, scroll to “SILENT PANIC”. Press ENTER to enable your selection of either PANIC to sound or not to sound an ALARM at the panel, if the alarm is transmitted from the SA-04 Remote Control. SILENTPANIC8ONZ EZon eNum b erRemote ControlType DisplayPANIC = Audiable PanicSILENT = Silent Duress AlarmZone B ox Status Disp layZONE = Zone is armedZONE (fla shing)= Zone was triggeredLCD Example of ZONE BOX DisplayMENUESCENTERADD R/FSET ZONEZONEPANIC8ZONECLEAR R/FSETSETENTERENTER6) Within the zone 8 menu, use the arrow key to select ADD RF and press enter, use the arrow key to select the desired available slots from 8.1 to 8.8, and press ENTER.7) When Prompted for RADIO, press any pushbuttons on the SA-04 to transmit,MENUESCENTERSETADD R/FZONE8ONZEPANIC& & ENTERENTERPress:PANIC Button togenerate an RFtransmission toenroll the SA-04 Hto the ControlPanel.

Navigation menu