Rosslare SA04G Panic Button Remote Control User Manual Visio SA 04 H Instruction Manual 010204 Page 1 vsd

Download:
Mirror Download [FCC.gov]
Document ID	540107
Application ID	oXbtoBwooS1P4QD67FS8rA==
Document Description	User Manual Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.39kB (517417 bits)
Date Submitted	2005-05-06 00:00:00
Date Available	2005-05-06 00:00:00
Creation Date	2004-02-12 16:34:07
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-12-27 04:18:42
Document Title	Visio-SA-04 H Instruction Manual 010204-Page 1.vsd
Document Creator	PScript5.dll Version 5.2
Document Author:	william

SA-04 Instruction Manual - Version 1.0 (Page 1/1)
Wireless Panic
Button Transmitter
This product may be sold in the following
member states of the European Community:
Austria
Germany
Norway
Belgium
Greece
Portugal
Denmark
Holland
Spain
Finland
Ireland
Sweden
France
Italy
United Kingdom
INSTALLATION INSTRUCTIONS
AND IMPORTANT INFORMATION
P/N:
9J-REL-xxx-xxxxxxxx-xx
INTRODUCTION (FAQ's)
INTRODUCTION (FAQ's) - continued;
Q: What is a Transmitter ?
A: A transmitter is an electronic device that
uses RF energy and coded digital messages to
control and communicate commands to other
electronic products.
Q: What is LOW BATTERY detection ?
A: For all supervised sensors, LOW BATTERY
detection is when a sensor continuously measures
its battery state and transmits a low battery signal
to the security panel when the battery's voltage
drops below a certain level. This alerts the user in
advance to replace a weak battery.
Q: What is SA-04 PANIC BUTTON and how can it
benefit me ?
A: SA-04 allows the user to set off the security
system alarm with just a press of the button, when
in a dangerous situation or in need of help, through
the Control Panel.
Q: What is SUPERVISOR or SUPERVISED sensor ?
A: A Supervised sensor continuously reports to the
receiver or security panel to confirm status of the
sensor and its presence. If the receiver fails to hear
from a sensor within a pre-programmed time, it
will presume a sensor is missing or malfunctioning
and notify the user. This provides added security.
GENERAL DESCRIPTION
OPERATION - GENERAL NOTES
The SA-04 is a miniature radio transmitter, designed
to send coded RF transmissions to wireless receivers
and control panels. The transmissions are activated by
depressing the pushbutton on the unit.
The SA-04 remote control is activated by pressing the
buttons on the unit and transmits this information to the
receiver panel.
The SA-04 Panic Button is a new addition to the
Rosslare’s wireless line, used for individuals who need
to feel additional protection fro their security system.
The SA-04 provides immediate access to the system,
causing an alarm to be announced with the push of a
single-button.
MAIN FEATURES
* Lightweight and easily transported with two types
methods of carrying.
* Long-range: provides security up to 100 meters from
the base.
* One-button operation: quick access in the event of an
emergency.
* Hermetically-sealed unit, against dust and water perfect for all-weather use, around the premises.
2) In the INSTALLER MENU, press the down arrow to
select the ZONE menu and press Enter
MENU
Q: What is a BACK TAMPER detector ?
A: Once the sensor is mounted and activated, the Back
Tamper detector ensures that the sensor is not
removed or vandalized by detecting any removal of
the unit from a wall or corner. The Back tamper
detector will alert the security panel in such cases.
Q: What is a CASE TAMPER detector?
A: A Case Tamper detector monitors any unauthorized
opening of the unit housing. A signal will be
transmitted to the security panel to notify the user
of such tampering.
ENTER
ENROLLING THE SA-04 TO THE SP-06
1) Using the installer pass code (8888) by pressing the
MENU button and entering the code on the keyboard,
enter the Installer Menu.
MENU
Since the SA-04is a portable wireless device and
system reception is dependent upon the conditions of
use as follows:
- AVOID: Placing the SA-04 near strong magnetic or
electrical fields other than the magnet with which it is
intended to be used. Otherwise, performance could be
affected and false alarms could occur.
- AVOID: Using near or behind large metal surfaces and
multiple concrete/steel walls. This may interfere or
block the wireless signals. Make sure to test the range
from the desired location by using the RF Test
Procedure to ensure reception.
MENU
PANIC
ZONE
ESC
CODE
MASTER CODE
SET
You will then enter the installer programming menu
for the SP-06 V control panel
MENU
- AVOID: Submerging in water.
SUPERVISION
SYSTEM
MASTER CODE
USER CODE
EXIT DELAY
CLOCK
TELEPHONE
TEST
SIREN TIME
SET OUTPUT
ESC
MODE
ZONE
PARTIAL
OFF
SET ZONE
CODE
ADD R/F
ACTIVATE
CLEAR R/F
CHIME
ENTRY DELAY
SILENT PANIC
ENTER
SET SIREN
4) To program operation of the Panic Button Use the
down arrow to select SET ZONE option and Press
Enter.
MENU
6) Within the zone 8 menu, use the arrow key to select
ADD RF and press enter, use the arrow key to select
the desired available slots from 8.1 to 8.8, and
press ENTER.
ENTER
MENU
ENTER
ESC
ZONE
SET ZONE
ADD R/F
CLEAR R/F
ESC
NUMBER
ZONE
SET ZONE
ADD R/F
CLEAR R/F
ENTRY DELAY
PANIC
ZONE
ESC
ZONE
ENTER
ADD R/F
3) In the ZONE menu, when prompted for the zone
number, press the number 8 to select Zone 8.
MENU
5) Press the SET key until the zone type shows “PANIC”,
for an audible emergency alarm, to enable the SA-04
to perform a non audible alarm, scroll to “SILENT
PANIC”. Press ENTER to enable your selection of
either PANIC to sound or not to sound an ALARM at
the panel, if the alarm is transmitted from the SA-04
Remote Control.
Zone
Number
8 PANIC ZONE
ESC
SET
ZONE
SET ZONE
ADD R/F
CLEAR R/F
Zone Box Status Display
ZONE = Zone is armed
ZONE (flashing)= Zone was triggered
SILENT
8 PANIC Z ON E
Remote ControlType Display
PANIC = Audiable Panic
SILENT = Silent Duress Alarm
ENTER
ENTER
SET
7) When Prompted for RADIO, press any pushbuttons
on the SA-04 to transmit,
Press:
PANIC Button to
generate an RF
transmission to
enroll the SA-04 H
to the Control
Panel.
LCD Example of ZONE BOX Display
11
10
SPECIFICATIONS
Battery:
OFF
INSTALL
8 PANIC ZONE
3-volt Lithium 165 mAh (non-removable)
CAUTION! Dispose of Properly, do not re-charge,
disassemble, heat or incinerate.
Operating Temp: - 10oC to + 50oC
- 4oF to + 122oF
Operating
Humidity:
Up to 95% Non-Condensing (max.)
RF Frequency:
Available in 433.92 or 68.35 MHz
Installation:
Worn on arm, keychain or around neck on necklace
Tamper:
There is no tamper on this device.
Supervisor:
No Supervisory signal exists with the SA-04,
allowing the unit to stay on the person, even
when leaving the system sensory area.
Current:
Standby - 0 uA
Transmit - 15 mA
Size:
45mm (diameter) x 15mm (thickness)
(1.77" " x 0.6 ")
Weight:
28 grams ( .21 oz) with battery
12
WARRANTY
The Manufacturer's warranty on this product is for a period of one year from the date
of manufacture against defects in materials and workmanship. Manufacturer's
warranty hereunder is limited to repair or replacement, at the manufacturer's sole
option, if the product is found to be defective in normal use during the warranty
period. The warranty is given in favor of the original purchase only. Subject to the
above warranty, manufacturer's liability and that of it's distributors, re-sellers and
agents and is wholly limited to the original purchase price and no payment will be
made for related or consequential loss including but not limited to labor costs incurred
in inspection, replacement or repair of defective products. This warranty is given
expressly and in place of all other expressed or implied warranties of merchantability
and fitness for a particular purpose and this warranty is the only warranty made by the
manufacturer. No agent, representatives or employee of the manufacturer has the
authority to waive, alter or add to the printed provisions of this warranty, to make
representation of warranty not contained herein or to extend this warranty to anyone
other than the original purchaser of the product. The SA-01 PIR is guaranteed
against defects in workmanship and material for a period of 12 (Twelve) months from
date of purchase. Return the faulty product with a dated proof of purchase to your
dealer for replacement.
INTERNATIONAL OFFICES
ISRAEL
Rosslare Israel Ltd (Center Office)
22 Hamelacha St, PO BOX 11407, Rosh Ha-Ayin, 48091,
NOTICE
Hong Kong:
Rosslare Enterprises Ltd.
905-912 Wing Fat Industrial Building
12 Wang Tai Road, Kowloon Bay,
Hong Kong. Tel (852) 2795 5630 Tel (852) 2795 1508
The SA-04 is designed to send an electronic signal to alarm control system,
should intrusion occur, the warranty does not make the manufacturer or the distributor
of the SA-01 PIR held liable for consequential damages resulting from any breech of
warranty, expressed or implied, applicable to their use.
U.S.A.:
Rosslare America Inc.
Westlake, Los Angeles, CA 91632 U.S.A
Tel: (818) 707 2974 Fax: (818) 7070543
Rosslare America Inc.
2001 Reliance, Packway, Suite D
Bedford, Texas 76021 U.S.A
Tel: (817) 685 9100 Fax: (817) 685 9188
Rosslare Powerpath NAPDC.
North America Product Development
22e. Howard St, # 238 Des Plaines, IL60018, U.S.A
Tel: (847) 827 6330 Fax: (847) 8276433
www.rosslare.com.hk

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:be609a21-2e22-43e3-a1da-1a7d15834168
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Create Date                     : 2004:02:12 16:34:07Z
Modify Date                     : 2004:12:27 04:18:42-02:00
Metadata Date                   : 2004:12:27 04:18:42-02:00
Creator Tool                    : PScript5.dll Version 5.2
Document ID                     : uuid:ed44faad-2fa3-4134-bd4a-47315adecaf4
Format                          : application/pdf
Creator                         : william
Title                           : Visio-SA-04 H Instruction Manual 010204-Page 1.vsd
Author                          : william

EXIF Metadata provided by EXIF.tools