Rosslare XR-16AG Wireless Expansion User Manual Installation Manual

Download:
Mirror Download [FCC.gov]
Document ID	1459661
Application ID	k2raOPRhFDNuKeMimMk3cg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.65kB (95571 bits)
Date Submitted	2011-05-05 00:00:00
Date Available	2011-05-09 00:00:00
Creation Date	2011-05-02 12:11:39
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2011-05-03 13:33:22
Document Title	Installation Manual
Document Creator	Acrobat PDFMaker 9.1 for Word
Document Author:	Doron Bodner

MatrixBus™ XR-16A
Installation Instructions
AuraSys™ L-4/6 Wireless Zone Expansion
1. Introduction
This wireless expansion transforms the AuraSys Lite system from a
limited hardwired system into a wireless system. The expansion is a
two way RF communicator which allows connection to wireless
sensors, sirens, keypads, repeaters and remote controls.
With up to 4/6 zones depending on the hosting panel having the
same characteristics as the on board zones.
The stand alone expansion option is housed in a plastic casing
installed outside of the system's case considering RF environment
and wireless devices deployment.
2. Technical Specifications
2.1. Electrical Characteristics
Auxiliary Voltage: 13.4 – 13.8 VDC from hosting panel
Maximum Input Current: 55-75 mA
Indication: Red LED
2.2. Environmental Characteristics
Operating Environment: indoor use
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity: 0 to 95% (Non-Condensing)
RFI Protection: >20 V/m up to 1000 MHz.
2.3. Physical Characteristics (with case)
Dimensions (HxWxD): 101 x 99 x 35 mm (4 x 3.9 x1.4 in)
Weight: 143 g (0.316 lbs)
2.4. Available models:
XR-16AH – 868.35 MHz
XR-16AG – 433.92 MHz
3. Installation
3.1. General
The XR-16A is designed for easy installation. Only a few steps are
required to install the keypad.
Changes or modifications to this equipment not expressly
approved by Rosslare security as the party responsible for
compliance could void the user’s authority to operate the
equipment.
9)
Make wiring connections, to the PCB assembly and mount
on the back plate.
10) Secure with the screws, set aside previously.
3.3. Wiring
Refer to the wiring diagram below.
3.2. Mounting the XR-16A expansion
Perform the following steps to mount the expansion:
1) Remove the four screws holding the front cover. Set the
screws aside.
2) Disassemble the PCB assembly from the back plate, remove
the four screws holding the PCB, set them aside.
3) Locate the back plate at the desired installation location.
The wireless expansion should be installed at a secured
location considering RF environment and wireless devices
deployment.
4) Use the back cover itself as a template for the wall screws.
5) Drill holes in the wall and insert anchors. Hardware is
provided.
6) Route a four-wire cable from the panel to the wireless
expansion location.
7) Pass the 4-wire cable via one of the channels designed in
the back plate. Use pliers to remove the section covering
the channel.
8) Mount and fasten the back plate using the screws provided.
Make sure to level the plate.
MatrixBUS
XR-16A
NOTE: Wiring must be done when the AuraSys™ L-4/6 panel
power is turned off.
4. Configuration
4.1. LEDs
The module LED flashes red until the panel finishes initialization of
Wireless module. After initialization, the wireless module turns the
LED on continuously.
During normal operation, when the module is in programming
mode, or any time the module is LOCKED, the LED flashes red.
4.2. Tamper
The module continuously checks the Tampers status when JP5 is
disconnected.
The JP5 jumper is the Tamper jumper. When using the expansion
on the board inside the metal casing the tampers must be
shorted in order to prevent false alarms.
When operating as a stand alone module, jumper JP5 must be
open (no jumper).
The stand alone expansion option cover and back tamper
switches prevent vandalism and unauthorized PCB access.
0706-0960344+01
5. Limited Warranty
conjunction with a Product, nor to any Product that is used with any ancillary
equipment, which is not furnished by ROSSLARE.
This warranty does not cover expenses incurred in the transportation, freight
cost to the repair center, removal or reinstallation of the product, whether or
not proven defective.
Specifically excluded from this warranty are any failures resulting from
Customer's improper testing, operation, installation, or damage resulting from
use of the Product in other than its normal and customary manner, or any
maintenance, modification, alteration, or adjustment or any type of abuse,
neglect, accident, misuse, improper operation, normal wear, defects or
damage due to lightning or other electrical discharge. This warranty does not
cover repair or replacement where normal use has exhausted the life of a part
or instrument, or any modification or abuse of, or tampering with, the Product if
Product disassembled or repaired in such a manner as to adversely affect
performance or prevent adequate inspection and testing to verify any warranty
claim.
ROSSLARE does not warrant the installation, maintenance, or service of the
Product. Service life of the product is dependent upon the care it receives and
the conditions under which it has to operate.
In no event shall Rosslare be liable for incidental or consequential damages.
ROSSLARE ENTERPRISES LIMITED S (Rosslare) TWO YEAR LIMITED
WARRANTY is applicable worldwide. This warranty supersedes any other
warranty. Rosslare's TWO YEAR LIMITED WARRANTY is subject to the
following conditions:
Warranty
Warranty of Rosslare's products extends to the original purchaser (Customer)
of the Rosslare product and is not transferable.
Products Covered By This Warranty and Duration
ROSSLARE ENTERPRISES LTD. AND / ORSUBSIDIARIES (ROSSLARE)
warrants that the MatrixBus XR-16A wireless zone expansion, to be free from
defects in materials and assembly in the course of normal use and service.
The warranty period commences with the date of shipment to the original
purchaser and extends for a period of 2 years (24 Months).
Warranty Remedy Coverage
In the event of a breach of warranty, ROSSLARE will credit Customer with the
price of the Product paid by Customer, provided that the warranty claim is
delivered to ROSSLARE by the Customer during the warranty period in
accordance with the terms of this warranty. Unless otherwise requested by
ROSSLARE ENTERPRISES LTD. AND / OR SUBSIDIARIES representative,
return of the failed product(s) is not immediately required.
If ROSSLARE has not contacted the Customer within a sixty (60) day holding
period following the delivery of the warranty claim, Customer will not be
required to return the failed product(s). All returned Product(s), as may be
requested at ROSSLARE ENTERPRISES LTD. AND /OR SUBSIDIARY’S sole
discretion, shall become the property of ROSSLARE ENTERPRISES LTD.
AND /OR SUBSIDIARIES.
To exercise the warranty, the user must contact Rosslare Enterprises Ltd. to
obtain an RMA number after which, the product must be returned to the
Manufacturer freight prepaid and insured
In the event ROSSLARE chooses to perform a product evaluation within the
sixty (60) day holding period and no defect is found, a minimum US$ 50.00 or
equivalent charge will be applied to each Product for labor required in the
evaluation.
Rosslare will repair or replace, at its discretion, any product that under normal
conditions of use and service proves to be defective in material or
workmanship. No charge will be applied for labor or parts with respect to
defects covered by this warranty, provided that the work is done by Rosslare
or a Rosslare authorized service center.
Limited Warranty Terms
THIS WARRANTY SETS FORTH THE FULL EXTENT OF ROSSLARE
ENTERPRISES LTD. AND IT’S SUBSIDIARIES’S WARRANTY
THE TERMS OF THIS WARRANTY MAY NOT BE VARIED BY ANY PERSON,
WHETHER OR NOT PURPORTING TO REPRESENT OR ACT ON BEHALF OF
ROSSLARE.
7B
THIS LIMITED WARRANTY IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES. ALL OTHER WARRANTIES EXPRESSED OR IMPLIED,
INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
SPECIFICALLY EXCLUDED.
78B
IN NO EVENT SHALL ROSSLARE BE LIABLE FOR DAMAGES IN EXCESS OF
THE PURCHASE PRICE OF THE PRODUCT, OR FOR ANY OTHER INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES, INCLUDING BUT NOT LIMITED TO
LOSS OF USE, LOSS OF TIME, COMMERCIAL LOSS, INCONVENIENCE, AND
LOSS OF PROFITS, ARISING OUT OF THE INSTALLATION, USE, OR INABILITY
TO USE SUCH PRODUCT, TO THE FULLEST EXTENT THAT ANY SUCH LOSS
OR DAMAGE MAY BE DISCLAIMED BY LAW .
Exclusions and Limitations
79B
THIS WARRANTY SHALL BECOME NULL AND VOID IN THE EVENT OF A
VIOLATION OF THE PROVISIONS OF THIS LIMITED WARRANTY.
80B
ROSSLARE shall not be responsible or liable for any damage or loss resulting
from the operation or performance of any Product or any systems in which a
Product is incorporated. This warranty shall not extend to any ancillary
equipment not furnished by ROSSLARE, which is attached to or used in
6. Declaration of Conformity
31B
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
97B
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
81B
82B
83B
84B
7. Contact information
32B
Asia Pacific, Middle East, Africa
Europe
42B
Headquarters:
4B
Global Technical Support & Training Center:
46B
47B
905-912 Wing Fat Industrial Bldg, 12 Wang Tai Road,
Kowloon Bay Hong Kong
Tel:+852 2795-5630 Fax: +852 2795-1508
E-mail: support.apac@rosslaresecurity.com
20B
14B
21B
HaMelecha 22 Rosh HaAyin, Israel 48091
Tel: +972 3 938-6838 Fax: +972 3 938-6830
E-mail: support.eu@rosslaresecurity.com
13B
15B
2B
South America
16B
United States and Canada
45B
17B
24B
Presbitero Actis 555, Oficina 31. San Isidro. Buenos Aires. Argentina
Tel: +5411-5273-6383 Tel: +305-921-9919
E-mail: support.la@rosslaresecurity.com
43B
23B
1600 Hart Court, Suite 103 Southlake, TX, USA 76092
Toll Free:+1-866-632-1101 Local:+1-817-305-0006 Fax: +1-817-305-0069
E-mail: support.na@rosslaresecurity.com
18B
25B
19B
Web Site: www.rosslaresecurity.com
48B
10TU
U10T
0706-0960344+01

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Doron Bodner
Company                         : Rosslare Security
Create Date                     : 2011:05:02 12:11:39+03:00
Modify Date                     : 2011:05:03 13:33:22+03:00
Source Modified                 : D:20110502091103
Tag Ad Hoc Review Cycle ID      : -350563605
Tag Author Email                : doron.bodner@rosslaresecurity.com
Tag Author Email Display Name   : Doron Bodner
Tag Email Subject               : files
Tag Reviewing Tools Shown Once  : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2011:05:03 13:33:22+03:00
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Document ID                     : uuid:611549b6-75cd-4cf3-8c73-26fb34f2fac8
Instance ID                     : uuid:0e2b7a96-e0dc-487c-a5fa-0ad3684c9774
Subject                         : 2
Format                          : application/pdf
Title                           : Installation Manual
Creator                         : Doron Bodner
Producer                        : Adobe PDF Library 9.0
Page Layout                     : OneColumn
Page Count                      : 2

EXIF Metadata provided by EXIF.tools