Rubbermaid Outdoor Storage 1S85 Users Manual Big Max Jr Assembly Instruction English
1S85 to the manual 6e31162f-7067-4ff6-8f14-18ab9fb49054
2015-02-06
: Rubbermaid Rubbermaid-Outdoor-Storage-1S85-Users-Manual-525560 rubbermaid-outdoor-storage-1s85-users-manual-525560 rubbermaid pdf
Open the PDF directly: View PDF 
.
Page Count: 9
| Download | |
| Open PDF In Browser | View PDF |
R M P N X D M G E C Q J F K H J-5H51 94.62" 45.06" Description Assembly Letter Floor Left Side Panel Right Side Panel Left Back Panel Right Door Panel Right Back Panel Left Front Panel Right Front Panel Left Door Panel Gable Left Roof Panel Right Roof Panel Wall Connector Ridge Beam Lock Hasp #14 x 1.0" Combo Pan Head Screw 1/4-20 x 0.5" Combo Round Head Bolt 1/4-20 Flat Washer 1/4-Hex Nut Roof Pin J-5H51 C D E F G H J K M N P Q R X AA BB CC DD EE Quantity 1 1 1 1 1 1 1 1 1 2 1 1 4 1 1 24 2 2 2 4 Required Tools Safety Glasses Rubber Mallet Phillips Screw Driver Liquid Soap 88.09" 1S85 RUBBERMAID 7' x 3'6" RESIN STORAGE BUILDING ASSEMBLY INSTRUCTIONS Pre-Assembly: • Review the parts list and make sure that no parts are missing. • Level the area where the shed will be located. • Areas of “fill dirt” should be tamped/compacted to prevent settling/sinking. • If a foundation is desired, it should be constructed before assembly. NOTE: To simplify assembly and to ensure proper engagement of all components, apply a mild detergent to dovetail and snap fits before assembling. (2) Step Stools/Stepladders Two Person Assembly 1 Level construcion site before beginning assembly of shed. A foundation may be constructed if desired. OPTIONAL STEP: If desired, recessed anchor locations (4 places) can be used to anchor the shed floor to a foundation. 41/8" 41/8" 76" 33/4" 33/4" 321/8" 437/16" 71/2" 71/2" 41/8" 41/8" 84" 43 7/16 " 84" 2 Using a utility knife, cut the long sides of each wall slot tab and then use a screwdriver to knock it out 14 places on Floor (J-5H51). Open hinge holes 2 places. J-5H51 3 Using a srewdriver, punch out the screw holes on the top of Left Side Panel (C) 2 Places. Connect Left Side Panel (C) into Floor (J-5H51). 4 Lubricate dovetails on Left Front Panel (H) 4 places with liquid soap. Connect Left Front Panel (H) into dovetails of Left Side Panel (C), engage snaps on bottom of Left Front Panel (H) into Floor (J-5H51). C Screw Holes 1 2 C click 1 J-5H51 C 2 H click J-5H51 J-5H51 click 5 Lubricate dovetails on Left Back Panel (E) 4 places with liquid soap. Connect Left Back Panel (E) into dovetails of Left Side Panel (C), engage snaps on bottom of Left Back Panel (E) into Floor (J-5H51). 6 Repeat Steps 3–5 to assemble right side of shed. Continue to Step 7. See Step 3 See Step 4 See Step 5 1 2 1 E C 2 G D J J-5H51 7 8 Repeat Steps 3–5 to assemble right side of shed. Continue to Step 7. E G Install Gable (M) onto top of back wall engaging the 2 dovetails and snaps on the back panel and the dovetail on the side panel on both the left and right sides of the shed. M 1 Q 1 E 9 2 2 G Install Gable (M) onto top of front wall engaging the 2 dovetails on the front panel and the dovetail on the side panel on both the left and right sides of the shed. DO NOT ENGAGE THE SNAPS. 10 Install Left Door Panel (K) inserting the lower hinge pin into Left Floor (A) socket, lift the left end of the Gable (M) enough to insert the top hinge pin on Left Door Panel (K) into the Gable (M) socket. 4 M M 3 2 K 1 11 Install Right Door Panel (F) inserting the lower hinge pin into Right Floor (U) socket, lift the right end of the Gable (M) enough to insert the top hinge pin on Right Door Panel (F) into the Gable (M) socket. Install Lock Hasp (X) into back side of Right Door Panel (F). Engage Gable (M) snaps on front wall. 12 Place Ridge Beam (R) into cups at the top of each Gable (M). R 4 M 2 3 M R M F 1 X 13 Washer Nut Align slots in Ridge Beam (R) with holes in Gable (M) tabs, install Bolt (BB), Washer (CC), and Nut (DD) 1 place, ONLY TIGHTEN NUT ‘FINGER’ TIGHT. Washer Plastic Tab on Gable DD CC M R Plastic Tab on Gable Bolt Head Nut Bolt Head M 14 Align slots in Ridge Beam (R) with holes in Gable (M) tabs, install Bolt (BB), Washer (CC), and Nut (DD) 1 place, ONLY TIGHTEN NUT ‘FINGER’ TIGHT. DD BB CC M R R M BB R 15 Lubricate roof snaps on Gable (M) 8 places on each Gable (M). Raise the Left Roof Panel (N) onto the left side of the shed assembly, the arrows on the roof panel should face the inside of the shed and point towards the Ridge Beam (R). M M N 16 Using (2) step stools (1 inside shed, 1 outside shed), lift the bottom of the roof panel above horizontal, guide the roof panel into the Ridge Beam (R), align both Gable (M) ribs with the channels in Left Roof Panel (N), engage Left Roof Panel (N) in Ridge Beam (R) by lowering the bottom of the roof panel onto the shed assembly (hold Ridge Beam (R) to prevent twisting). 1 2 3 N 2 R 3 N R R M M Channel Roof Panel 3 Rib Gable Rib 17 16 Engage all snaps between the roof panel and gable, then roof panel and wall panel. 18 Repeat Steps 15–17 for right roof of shed. P R See Steps 15–17 1 2 N P 1 Back of shed shown 19 Install Screws (AA) 16 places in Gable (M). AA (16) Caution: When installing screws do not overtighten. 20 While one person holds down the bottom of the roof, install screws (AA) 4 places in screw holes on the top of the Side Panels (C&D). Screws connect the Side Panels to the Roof Panels. AA (4) Caution: When installing screws do not overtighten. 21 Install Roof Pins (EE) 4 places connecting the Roof Panels to the Gables. EE (4) OPTIONAL STEP: If desired, add wood to create a loft (wood not included). .75" x 24" x 37.5" .75" x 37.25" x 37.5" .75" x 24" x 37.5" 94.62" 88.09" Printed in U.S.A. © 2012 Rubbermaid Incorporated Huntersville, NC U.S.A. 28078-1801 www.rubbermaid.com 45.06" Customer Service Toll Free: 1-888-895-2110 M–F 8:30 AM to 5:00 PM EST or visit us at www.rubbermaid.com 1869757
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Rubbermaid Create Date : 2012:11:21 07:08:07-05:00 Keywords : Rubbermaid, Big, Max, Jr, Assembly, Instruction, Manual, English Modify Date : 2013:05:22 10:47:57-04:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2013:05:22 10:47:57-04:00 Creator Tool : Adobe Illustrator CS5 Format : application/pdf Title : Rubbermaid Big Max Jr Assembly Instruction Manual English Description : Rubbermaid Big Max Jr Assembly Instruction Manual English Creator : Rubbermaid Subject : Rubbermaid Big Max Jr Assembly Instruction Manual English Document ID : uuid:01628028-885d-5c4a-bb6e-c04a7b36a27b Instance ID : uuid:6a174bff-33cf-4f08-ae3a-9b028d2f90ba Producer : Adobe PDF library 9.90 Page Layout : SinglePage Page Mode : UseThumbs Page Count : 9 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools