Ruckus Wireless R500 IEEE 802.11ac Access Point User Manual R500 Quick Setup Guide

Download:
Mirror Download [FCC.gov]
Document ID	2375538
Application ID	BFole1sKpQRsXzb7LjgCCg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	58.88kB (735971 bits)
Date Submitted	2014-09-02 00:00:00
Date Available	2014-09-02 00:00:00
Creation Date	2017-10-21 09:50:18
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-21 09:50:18
Document Title	R500 Quick Setup Guide
Document Creator	FrameMaker 11.0.2
Document Author:	Ruckus Wireless, Inc.

STEP 1:
MENTS
•
R500 Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions
on how to set up your Ruckus Wireless R500 Dual Band
802.11ac Multimedia Wi-Fi Access Point. After completing
the steps described in this Guide, you will be able to place
the Access Point (AP) at your site and provide wireless
network access to users.
Note: The R500 requires a minimum of ZoneFlex (ZF)
firmware version 9.8.1 or later or SmartCell Gateway
(SCG) firmware version 2.5.1 or later.
COLLECT TOOLS AND SETUP REQUIRE-
A computer running Windows 7 (procedures for other OS’s
are similar)
•
Two Cat 5e Ethernet cables
•
No. 2 Phillips screwdriver and T8 Torx driver for wall mounting anchor kit
•
An AC power adapter (sold separately), or
•
An 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector
IMPORTANT! If the AP is deployed with a ZoneDirector, then
STEP 3: PREPARE YOUR COMPUTER
SETUP
TO
YOUR COMPUTER
Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
The TCP/IPv4 Properties dialog box appears.
Important! Write down all of the currently active settings so
you can restore your computer to its current configuration
later (when this process is complete).
Figure 1: Top view
IP address: 192.168.0.22 (or any address in the
192.168.0.x network)
• Subnet mask: 255.255.255.0
• Default gateway: 192.168.0.1
Leave the DNS server fields empty.
User Guides and Release Notes are available at
http://support.ruckuswireless.com/software.
•
Open Source information is available at
http://opensource.ruckuswireless.com.
•
Software License and Limited Warranty are available at
http://support.ruckuswireless.com/warranty.
R500 Access Point
•
Two wall-mount anchor kits, including two 1" No. 8 steel
panhead Phillips sheet metal screw screws, one 5mm M2.5 x
1.06 Torx security screw, and wall-mount anchors
•
One external T-bar bracket (two unassembled parts)
•
One unit removal pin
•
Regulatory flyer
•
Product warranty statement
•
Declaration of Conformity, if required
•
This Quick Setup Guide
Copyright © 2014 Ruckus Wireless, Inc.
Published July 2014, Part Number 800-70564-001 Rev A
After removing your Ruckus Wireless AP from its package, place it next to your computer.
Using an Ethernet cable, connect your computer’s network port to one of the two ports on the AP.
Using an AC adapter (sold separately), connect the AP
12VDC port to a protected power source.
PACKAGE CONTENTS
•
Select Use the following IP address (if it is not already
selected) and then make the following entries:
•
http://support.ruckuswireless.com/documents.
Software Upgrades are available at
Start > Control Panel > Network and Sharing
Center > Change Adapter Settings
Edit the TCP/IPv4 address settings as follows:
•
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
•
On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as follows:
•
BEFORE YOU BEGIN
•
AP
Note: The following procedures assume Windows 7 as the
operating system. Procedures for other OS’s are similar.
refer to the ZoneDirector Quick Setup Guide and connect the
AP to your local network.
STEP 2: CONNECT THE AP
FOR
Alternatively, connect the PoE port to a PoE injector or
switch for both power and network connections.
Verify that the Power LED on the external enclosure is a
steady green.
Figure 2: Bottom view
PoE Port
Click OK to save your changes.
Your changes are put into effect immediately.
STEP 4: LOG INTO THE AP
As specified earlier, the AP should be directly connected to
your computer (through one of the Ethernet ports) and
powered on, ready for setup.
On your computer, open a Web browser window.
In the browser, type this URL to connect to the AP:
https://192.168.0.1
Press  to initiate the connection. When a security alert dialog box appears, click OK/Yes to proceed.
When the Ruckus Wireless Admin login page appears,
enter the following:
12VDC Port
• Username: super
• Password: sp-admin
Click Login.
Page 1 of 4
STEP 5: CUSTOMIZE
THE
WIRELESS SETTINGS
Default AP Settings (For Your Reference)
Network Names (SSIDs)
Wireless1—Wireless8
(2.4GHz radio)
Wireless9—Wireless16 (5GHz
radio)
STEP 6: PLACE
Default Management IP
Address
192.168.0.1
On the Web interface menu, click Configuration >
Radio 2.4G or Configuration > Radio 5G. The
Configure :: Wireless :: Common options appear.
Use an Ethernet cable to connect the PoE port to the
appropriate device:
The ISP’s or carrier’s network device
The Ethernet switch that is connected to the ISP’s or
carrier’s network device
Use a 5mm drill bit to drill holes approximately 25mm
into the mounting surface (A in Figure 3).
After a short pause to re-establish the Internet connection,
you can test the AP.
Insert the anchors and mounting screws into the mounting surface, leaving approximately 1/4” (6 mm) of the
screw heads protruding for the AP enclosure.
Insert the unit removal pin into the hole on the side of
the AP to release the locking mechanism (B in Figure 3).
Place the AP onto the mounting screws so that the screw
heads enter the mounting holes on the AP enclosure,
and push the AP down to lock in place.
Remove the unit removal pin to release the locking
mechanism and secure the AP.
To remove the AP, insert the unit removal pin into the
hole on the side of the AP to unlock, then push the AP up
to release the AP enclosure from the mounting screws.
Connect the AP power adapter (or PoE power supply) to
the AP, then to a convenient power source.
Verify that the PoE port LED is lit.
Click any of the “Wireless #” tabs at the top of the page.
STEP 7: VERIFY THE INSTALLATION
In Wireless Availability, click Enabled.
Delete the text in the SSID field, then type a name for
your network that will help your users identify the AP in
their wireless network connection application.
Repeat Steps 4-7 for each Wireless # interface that you
want to enable.
Click Logout to exit the Web interface.
Optional: If You Want To Switch from DHCP (Default):
If you anticipate logging into the AP regularly to perform
monitoring or maintenance once it is in place, you may want
to consider assigning a static IP address to the AP.
In a default AP configuration, the AP uses a DHCPassigned IP address.
A. On the menu, click Configuration > Internet.
B. Click the Static IP option.
C. Fill in the IP Address and Mask fields.
D. Click Update Settings to save your changes.
Mounting on a Flat Surface
Mounting on a Recessed Drop-Ceiling T-Bar
Mounting on a Flush Drop-Ceiling T-Bar
Mounting on a Flat Surface
Note: If you will be using PoE, then you will need a Cat 5e
(or better) Ethernet cable to connect the AP to the PoE
injector or switch.
Click Update Settings to save your changes.
•
•
•
Use the Mounting Template on the last page of this
Quick Setup Guide as a template to mark the locations
for drill holes on the mounting surface. There are two
sets of keyholes available on the AP. One allows the AP
to be mounted to a wall or ceiling. The other allows the
R500 to be mounted to an accessory bracket (not
included).
Channel: SmartSelect
Country Code: If you are not located in the United
States, select your current country.
Click Update Settings if you made any changes.
(OPTIONAL) MOUNTING INSTRUCTIONS
The R500 can be mounted to a T-bar, wall or ceiling a using
the enclosed mounting kits. Refer to the following sections:
Verify that the following options are active:
•
•
AP IN YOUR SITE
Move the AP to its permanent location (accessible to
both power and network connections). Refer to
(Optional) Mounting Instructions for physical installation.
•
•
Security (Encryption method) Disabled for each wireless
interface
THE
Using any wireless-enabled computer or mobile device,
search for and select the wireless network you previously
configured.
If you can connect, open a browser and link to any public
Web site.
Congratulations! Your wireless network is active and ready
for use.
FOR MORE INFORMATION
You can now use the wireless network to log into the AP’s
Web interface. For information on how to configure the AP,
refer to the Ruckus Wireless ZoneFlex Indoor Access Point
User Guide.
Figure 3. Flat surface mounting
10 When the Ruckus Wireless Admin login page reappears,
you can exit your browser.
11 Disconnect the AP from the computer and from the current power source, and then restore your computer to its
original network connection configuration.
Copyright © 2014 Ruckus Wireless, Inc.
Published July 2014, Part Number 800-70564-001 Rev A
Page 2 of 4
Mounting on a Recessed Drop-Ceiling T-Bar
Note: This mounting bracket can also be used on a flush
drop-ceiling T-bar, so the four rubber feet on the bottom
of the AP minimize ceiling tile displacement.
Hold the R500 in place and gently push the locking tab
(B in Figure 5) until its clasp grips the other edge of the Tbar.
CAUTION: Make sure that all three clasps are gripping the Tbar!
Removing an External Bracket from a T-Bar
•
•
•
Insert the unit removal pin (A in Figure 4) into the hole on
the side of the R500 (B in Figure 4) to release the locking
mechanism.
Figure 4. Attaching the external bracket to the AP
•
•
Mounting an AP using the Integrated Bracket
Removing an AP Integrated Bracket from a T-Bar
Mounting an AP using the Integrated Bracket
The enclosed T-bar bracket supports mounting to recessed
drop ceiling T-bars.
Mounting an AP using the External Bracket
Removing an External Bracket from a T-Bar
Removing an External Bracket from an AP
Mounting an AP using the External Bracket
Mounting on a Flush Drop-Ceiling T-Bar
Move the ceiling tiles out of the way.
Gently lift up the locking tab (A in Figure 6) by sliding
your fingers under the tab.
While lifting up on the locking tab, rotate the R500and-T-bar bracket assembly (B in Figure 6). The R500and-T-bar bracket assembly comes away from the Tbar.
Orient the AP so that the T-bar is positioned between
the T-bar clips as shown in Figure 8, then rotate the AP
until the third T-bar clip catches the T-bar and the
latch locks the T-bar in place (Figure 9).
Figure 8. Attaching the integrated bracket to the T-bar
Figure 6. Removing the external bracket from the T-bar
Figure 9. Locking the integrated bracket to the T-bar
Removing an External Bracket from an AP
Position the studs on the bottom of the T-bar bracket (C
in Figure 4) in the mounting holes on the R500 enclosure,
and then slide the T-bar bracket until the studs are in the
narrow parts of the R500 mounting keyholes (arrow).
Remove the unit removal pin (A in Figure 4) to engage
the locking mechanism and secure the T-bar bracket to
the R500.
Make sure that the locking tab (D in Figure 4) is in the
first position on the T-bar bracket (C in Figure 4).
Gently push the ceiling tiles up and out of the way.
Position the T-bar bracket so its two clasps grip one edge
of the T-bar (A in Figure 5). Make sure that both clasps
are gripping the T-bar.
Insert the unit removal pin (A in Figure 7) into the hole
on the side of the R500.
Gently lift up the retainer tab (B in Figure 7).
Gently push the T-bar bracket (C in Figure 7) until it
detaches from the R500.
Figure 7. Removing the external bracket from an AP
Insert the Torx security screw into the hole near the
latch to lock the AP in place.
Removing an AP Integrated Bracket from a T-Bar
To remove the AP from a T-bar, first remove the
security screw, then depress the latch while rotating
the AP so that the T-bar clips disengage the T-bar.
Figure 5. Attaching the external bracket to the T-bar
Copyright © 2014 Ruckus Wireless, Inc.
Published July 2014, Part Number 800-70564-001 Rev A
Page 3 of 4
Mounting Template
Copyright © 2014 Ruckus Wireless, Inc.
Published July 2014, Part Number 800-70564-001 Rev A
Page 4 of 4
Page 1
Federal Communications Commission Notices
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Statement
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile
satellite systems; the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p.
limit; and the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point
and non point-to-point operation as appropriate.
Le dispositif de fonctionnement dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur pour réduire le risque d'interférences nuisibles
à la co-canal systèmes mobiles par satellite, le gain d'antenne maximal autorisé pour les appareils dans les bandes 5250-5350 MHz et 5470-5725
MHz doit se conformer à la pire limite, et le gain d'antenne maximal autorisé pour les appareils dans la bande 5725-5825 MHz doivent être conformes
avec le pire limites spécifiées à point-à-ponctuelles et non point-à-point de fonctionnement selon qu'il convient.
Operation in the 5600-5650 MHz band is not allowed in Canada. High-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Opération dans la bande 5600-5650 MHz n'est pas autorisée au Canada. Haute puissance radars sont désignés comme utilisateurs principaux (c.-àutilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer des interférences et / ou des dommages à
dispositifs LAN-EL.
Radiation Exposure Statement
The device has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091 and Industry Canada RSS-102 for an
uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Le dispositif a été jugé conforme aux exigences énoncées dans les articles 47 CFR 2.1091 et Industrie Canada RSS-102 pour un environnement non
contrôlé. L'antenne (s) utilisée pour ce transmetteur doit être installé pour fournir une distance de séparation d'au moins 20 cm de toutes les
personnes et ne doit pas être co-localisés ou fonctionner en conjonction avec une autre antenne ou transmetteur.
Mexico Statement
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia
perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.”
Page 2
Professionally Installed Products
The product is to be installed according to the installation instructions. The Use/Operator does not have access to the device once the device is
installed and in use. Provisions for permanent grounding are provided.
1. Installation personal: This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule
knowledge. The general user shall not attempt to install or change the setting.
2. Installation location: The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in normal
operation condition to meet regulatory RF exposure requirement. Additionally, installation locations with 35km of Terminal Doppler Weather Radar
locations shall follow instructions below.
a. Any installation of either a master or a client device within 35 km of a TDWR location shall be separated by at least 30 MHz center-tocenter) from the TDWR operating frequency.
b. A voluntary WISPA sponsored database has been developed that allows operators and installers to register the location information of the
UNII devices operating outdoors in the 5470 – 5725 MHz band within 35 km of any TDWR location (see
http://www.spectrumbridge.com/udia/home.aspx ). This database may be used by government agencies in order to expedite resolution of
any interference to TDWRs.
c. Addition information can be obtained from the FCC Knowledge Database, Publication Number 443999.
https://apps.fcc.gov/oetcf/kdb/index.cfm
3. External antenna: Use only the antennas which have been approved by Ruckus Wireless. The non-approved antenna(s) may produce unwanted
spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited.
4. Installation procedure: Please refer to user’s manual for the detail.
5. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in US Rule
CFR 47 part 15 section 15.247 & 15.407. The violation of the rule could lead to serious federal penalty.
External Antenna Notice
This radio transmitter has been approved by the FCC and Industry Canada to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a
été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et
l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Model: ZoneFlex 7441 [ZF7441]: This device has been designed to operate with an antenna having maximum gain of 2dBi. Other antenna types or
having greater gain are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
Model: ZoneFlex 7372E [ZF7372E]: This device has been designed to operate with an antenna having maximum gain of 7dBi. Other antenna types
or having greater gain are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.
Products intended to be powered by an external power supply:
Caution –This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked Class 2 or LPS (sub-clause 2.5 of standard EN 609501). Available Ruckus power supplies intended for product operation are identified in the product datasheet. The last two digits of the power supply
part number represent the country code. For additional applicable power supplies/options, see user instructions and product datasheet.
Australia Statement
This device complies with the ACMA requirements for a Wi-Fi device namely Radio Communications (Low Impact Potential Devices) Class Licence
2000 Amd. 1:2007 and Radiocommunications (Compliance Labelling – Electromagnetic Radiation) Notice 2003. The equipment complies with the
ACMA requirements for radiation exposure for a "general user/non-aware user". This equipment should be installed and operated with a minimum
distance of 20 cm between the radiator and your body. This equipment complies with the Australian safety requirements and should only used with
the specified power adapter according to the product datasheet.
Brazil Statement
For Brazil, those products are designed for specific application and needs to be installed by a qualified personal who has RF and related rule
knowledge. Regarding the operation on range of 5150 MHz to 5350 MHz , the average output power of the equipments must be adjusted to the
maximum limit of - 0,48 dBm and for 5470 MHz to 5725 MHz, the average output power of the equipments must be adjusted to the maximum limit of
6,44 dBm.
Para o Brasil, esses produtos são projetados para aplicações específicas e necessidades a serem instalados por um pessoal qualificado que tenha
conhecimento regra RF e afins.Em relação à operação em série de 5150 MHz a 5350 MHz, a potência média de saída dos equipamentos deve ser
ajustado para o limite máximo de - 0,48 dBm e para 5470 MHz a 5725 MHz, a potência média de saída dos equipamentos deve ser ajustada ao limite
máximo de 6,44 dBm.
Taiwan Statement
本產品為5.25-5.35 GHz頻帶內操作之UNII設備, 僅限於室內使用
The frequency band 5250 – 5350 MHz is restricted to indoor use.
經型式認證合格之低 率射頻電機，非經許可，公司 商號或使用者均不得擅自變更頻率
大 率或變更原設計之特性及 能
低 率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用
電信法規定作業之無線電通信 低 率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機設備之干擾.
前項合法通信，指依
The control, adjustment and on/off operation of this device does not violate the “Administrative regulations on low power radio waves radiated
devices”. Any adjustments to the device should be carried out or be monitored by a specialist who has expertise on radio frequency devices.
Replacement of components which may lead to the violation to the regulations is not allowed. Without permission granted by the NCC, any company,
enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to an
approved low power radio-frequency devices. The low power radio-frequency device shall not influence aircraft security and interfere with legal
Page 3
communications; if found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio
communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must not be susceptible with the
interference from legal communications or ISM radio wave radiated devices.
AT
FI
IT
PL
GB RO
BE FR
LV
PT
IS
TR
European Union Notices and National Restrictions
CY DE
LT
SK LI
CZ
GR LU
SI
NO
The frequency band 5150 – 5350 MHz is restricted to indoor use
DK HU
MT ES CH
Italy
EE IE
NL
SE BG
This product meets the National Radio Interface and the requirements specified in the National Frequency
Allocation Table for Italy. Unless operating within the boundaries of the owner’s property, the use of this 2.4 GHz Wireless LAN product requires a
‘general authorization’. Please check with http://www.comunicazioni.it/ for more details.
Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non
viene installato all’interno del proprio fondo, l’utilizzo di prodotti Wireless LAN a 2.4 GHz richiede una "Autorizzazione Generale". Consultare
http://www.comunicazioni.it/ per maggiori dettagli.
Belgium
The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300
meters. Please check http://www.bipt.be for more details. / Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter
dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie http://www.bipt.be voor meer gegevens. /
Les liaisons sans fil pour une utilisation en extérieur d’une distance supérieure à 300 mètres doivent être notifiées à l’Institut Belge des services
Postaux et des Télécommunications (IBPT). Visitez http://www.ibpt.be pour de plus amples détails.
Česky
[Czech]
Ruckus Wireless tímto prohlašuje, že tento Radio LAN je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede Ruckus Wireless erklærer herved, at følgende udstyr Radio LAN overholder de væsentlige krav og øvrige
relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt Ruckus Wireless, dass sich das Gerät Radio LAN in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab Ruckus Wireless seadme Radio LAN vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud
direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, Ruckus Wireless declares that this Radio LAN is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente Ruckus Wireless declara que el Radio LAN cumple con los requisitos esenciales y cualesquiera
otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Εζζηνδεή
[Greek]
ΜΕ ΣΗΝ ΠΑΡΟΤ΢Α Ruckus Wireless ∆ΗΛΩΝΕΙ ΟΣΙ Radio LAN ΢ΤΜΜΟΡΦΩΝΕΣΑΙ ΠΡΟ΢ ΣΙ΢ ΟΤ΢ΙΩ∆ΕΙ΢
ΑΠΑΙΣΗ΢ΕΙ΢ ΚΑΙ ΣΙ΢ ΛΟΙΠΕ΢ ΢ΧΕΣΙΚΕ΢ ∆ΙΑΣΑΞΕΙ΢ ΣΗ΢ Ο∆ΗΓΙΑ΢ 1999/5/ΕΚ.
Français
[French]
Par la présente Ruckus Wireless déclare que l'appareil Radio LAN est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente Ruckus Wireless dichiara che questo Radio LAN è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo Ruckus Wireless deklarē, ka Radio LAN atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo Ruckus Wireless deklaruoja, kad šis Radio LAN atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos
nuostatas.
Nederlands
[Dutch]
Hierbij verklaart Ruckus Wireless dat het toestel Radio LAN in overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, Ruckus Wireless, jiddikjara li dan Radio LAN jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, Ruckus Wireless nyilatkozom, hogy a Radio LAN megfelel a vonatkozó alapvetõ követelményeknek és az
1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym Ruckus Wireless oświadcza, że Radio LAN jest zgodny z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
Ruckus Wireless declara que este Radio LAN está conforme com os requisitos essenciais e outras disposições da
Directiva 1999/5/CE.
Slovensko
[Slovenian]
Ruckus Wireless izjavlja, da je ta Radio LAN v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive
1999/5/ES.
Slovensky
[Slovak]
Ruckus Wireless týmto vyhlasuje, že Radio LAN spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice
1999/5/ES.
Suomi
[Finnish]
Ruckus Wireless vakuuttaa täten että Radio LAN tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar Ruckus Wireless att denna Radio LAN står I överensstämmelse med de väsentliga egenskapskrav och
övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Íslenska
[Icelandic]
Hér með lýsir Ruckus Wireless yfir því að Radio LAN er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í
tilskipun 1999/5/EC.
Norsk
[Norwegian]
Ruckus Wireless erklærer herved at utstyret Radio LAN er i samsvar med de grunnleggende krav og øvrige relevante
krav i direktiv 1999/5/EF.
800-70402-002-G
Page 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : Ruckus Wireless, Inc.
Create Date                     : 2007:02:21 14:03:02Z
Modify Date                     : 2014:09:02 11:00:56-07:00
Subject                         : R500 Quick Setup
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : Ruckus Wireless, Inc.
Description                     : R500 Quick Setup
Title                           : R500 Quick Setup Guide
Creator Tool                    : FrameMaker 11.0.2
Metadata Date                   : 2014:09:02 11:00:56-07:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:9cce3435-3972-4bc8-8fd8-c222e9aed7e1
Instance ID                     : uuid:493c39c4-c6c6-4922-9b05-f5a3f9640f66
Page Layout                     : OneColumn
Page Mode                       : UseOutlines
Page Count                      : 8

EXIF Metadata provided by EXIF.tools