Ruckus Wireless T610 ZoneFlex T610 Access Point, ZoneFlex T610s Access Point User Manual T610

Download:
Mirror Download [FCC.gov]
Document ID	3136200
Application ID	V3J+E/QiRrkoPps08iVvVA==
Document Description	T610 User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	129.05kB (1613139 bits)
Date Submitted	2016-09-15 00:00:00
Date Available	2017-03-14 00:00:00
Creation Date	2007-02-21 14:03:02
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2016-06-24 09:38:43
Document Title	T610 User Manual
Document Creator	FrameMaker 11.0.2

T610 Access Point
Quick Setup Guide
CAUTION! The minimum software revision for the T610
is ZoneDirector (ZD) 9.13.1 or later, or SmartZone (SZ) 3.4
or later, or standalone AP firmware 104.0 or later.
DO NOT CONNECT THE T610 TO A RUCKUS
WIRELESS ZONEDIRECTOR RUNNING 9.13 OR
EARLIER.
This Quick Setup Guide provides step-by-step instructions on how to
field-install the Ruckus Wireless T610 access point (AP).
For detailed information on planning the installation, performing a site
survey, and operating the T610, refer to the ZoneFlex Outdoor Access
Point User Guide, available at https://support.ruckuswireless.com.
WARNING: Only trained and qualified personnel should be allowed to
install, replace, or service this equipment.
WARNING: Installation of this equipment must comply with local and
national electrical codes.
CAUTION: Make sure that you form a 80mm - 130mm (3”-5”) drip
loop in any cable that is attached to the AP or the building. This will
prevent water from running along the cable and entering the AP or the
building where the cable terminates.
CAUTION: Be sure that grounding is available and that it meets local
and national electrical codes. For additional lightning protection, use
lightning rods and lightning arrestors.
CAUTION: Make sure that proper lightning surge protection
precautions are taken according to local electrical code.
WARNING: Ruckus Wireless strongly recommends that you wear eye
protection before mounting the T610.
Copyright © 2016 Ruckus Wireless, Inc.
Published June 2016, Part Number 800-71230-001 Rev A
THIS GUIDE IN OTHER LANGUAGES
PACKAGE CONTENTS
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse suivante
https://support.ruckuswireless.com.
こ の ガ イ ド の⽇本語版は https://support.ruckuswireless.com
で ご 覧 く だ さ い。
이 가이드의 한국어 버전은 웹 사이트
(https://support.ruckuswireless.com) 에서 확인하시기 바랍니다 .
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com.
A complete T610 field installation package includes all of the items
listed below (see Figure 1for illustrations):
• T610 Access Point (A)
• Two M25 data cable glands (B)
• Ground wire with lug (C)
• Service Level Agreement/Limited Warranty Statement
• Declaration of Conformity
• Regulatory Statement
• Ruckus Wireless AP Getting Started Guide
• This Quick Setup Guide
Figure 1:
Package Contents
BEFORE YOU BEGIN
Before deploying your Ruckus Wireless T610, verify that all items listed
in Package Contents are included in the package. If any item is
damaged or missing, notify your authorized Ruckus Wireless sales
representative. Also, make sure that you have the required hardware
and tools.
REQUIRED HARDWARE AND TOOLS
•
•
•
•
•
•
•
•
•
•
•
Customer-supplied outdoor-rated three-wire (1-2mm2 or 1418AWG) AC cable
1/2” (13mm) flat-blade screwdriver or equivalent
No. 2 Phillips screwdriver
Small flat-blade screwdriver
Torque wrench or torque screwdriver with sockets
Long-nose pliers
Electrical wire stripping and terminal crimping pliers
Pipe or pole --OR-- a sturdy flat surface
Electric drill with drill bits and customer-supplied wall anchors, flat
washers, and hex nuts for flat-surface mount
Four factory-supplied 1/2” (12.7mm) wide stainless steel
adjustable clamps, 2.5” (63.5mm) diameter, for main mounting
bracket on smaller poles
Ruler
NOTE: The outdoor AP Mounting Bracket and security cable are
optional accessories that must be purchased separately.
Page 1 of 4
STEP 1: CONNECTING AND SEALING THE RJ-45
CABLES
STEP 2: ATTACHING THE U-JOINT BRACKET TO THE
MOUNTING BRACKET
Connect and seal the RJ-45 cable(s) using the M25 data cable gland
as shown in Figure 3.
WARNING: Do not use any PoE injector not tested and approved by
Ruckus Wireless to power the T610 Access Point.
WARNING: Do NOT plug PoE in power into the non-PoE Port (see
Figure 2).
NOTE: The following mounting instructions require purchase of
optional accessories that are not included in the standard T610
package. The outdoor AP Mounting Bracket and safety cable are
optional accessories that must be purchased separately.
1 Position the U-joint bracket on the mounting bracket.
STEP 3B: ATTACHING THE MOUNTING BRACKET TO A
METAL POLE
Figure 4:
Figure 2:
U-joint bracket attached horizontally to the mounting bracket
T610 bottom view
Using the mounting hardware instructions, tighten the hardware to
secure the mounting bracket.
Continue with Step 4: Mounting the Linkage Bracket to the UJoint Bracket.
Insert the open end of one steel clamp into the upper two slots on
the mounting bracket.
2 Take the other steel clamp and insert it into the lower two slots on
the mounting bracket.
NOTE: The clamps can be daisy-chained together to accommodate
larger poles.
3 Use the clamps to attach the mounting bracket to the pole.
Tighten the clamps to 3 N.m or 27 in-lbs, or per manufacturer’s
specifications.
Figure 6:
Attaching the mounting bracket to a vertical pole
NOTE: Mount the U-joint bracket in any direction on the mounting
bracket, preferably to allow AP azimuth adjustments. Then the AP
bracket allows AP elevation adjustments.
Feed the end of the cable through the sealing nut, rubber O-ring,
clamping ring assembly and cable gland base as shown in Figure
3.
Figure 3:
RJ-45 cable and cable gland assembly
Cable gland base
Clamping ring assembly
Rubber O-ring
Sealing nut
Use a wide flat-blade screwdriver to remove the required (PoE IN)
blanking cap from the T610.
Connect the cable to the Ethernet port on the T610.
Tighten the cable gland base into the T610 chassis to 7 N.m or
62 in-lbs.
Wrap the clamping ring assembly around the rubber O-ring. Make
sure that the clamping ring assembly fully encloses the rubber Oring.
Seat the clamping ring assembly and rubber O-ring in the cable
gland base.
Hand-tighten the sealing nut.
Copyright © 2016 Ruckus Wireless, Inc.
Published June 2016, Part Number 800-71230-001 Rev A
Use four 1/4-28 bolt and washer sets (A) to mount the U-joint
bracket (B) to the mounting bracket (C). Tighten the bolts to 9.5
N.m (7 ft-lbs).
Continue with Step 3a: Attaching the Mounting Bracket to a
Flat Surface or Step 3b: Attaching the Mounting Bracket to a
Metal Pole.
STEP 3A: ATTACHING THE MOUNTING BRACKET TO A
FLAT SURFACE
Place the mounting bracket at the location on the flat surface
where you want to mount the AP. Use the holes on the mounting
bracket as a template to mark the locations of the mounting
holes.
Figure 5:
Mounting bracket flat surface holes
Continue with Step 4: Mounting the Linkage Bracket to the UJoint Bracket.
STEP 4: MOUNTING THE LINKAGE BRACKET TO THE
U-JOINT BRACKET
The linkage bracket attaches to the U-joint bracket using an M8 bolt
and washer set. The linkage bracket is symmetrical, and either end
can be attached to the U-joint bracket.
NOTE: Make sure that linkage bracket is installed with its serrated
external-tooth lock washer on the inside of the U-joint bracket
flanges. This ensures that the azimuth adjustment does not
change.
Loosely assemble the linkage bracket (A), the U-joint bracket (C),
one serrated external-tooth lock washer (B), and one M8 bolt
and washer set (D).
2 Remove the mounting bracket from the flat surface.
3 Drill holes required for the mounting hardware.
NOTE: The hardware required for mounting to a wall are not included
in the mounting kit.
4 Attach the mounting bracket to the flat surface using the
mounting hardware.
Page 2 of 4
Figure 7:
Attaching the linkage bracket to the U-joint bracket
STEP 6: ATTACHING THE AP BRACKET TO THE
ACCESS POINT
Place the AP bracket onto the back side of the AP so that the four
larger screw holes on the bracket align with the four screw holes
on the AP. Make sure that the end of the AP bracket with the
hoisting loop is on the same side as the AP PoE IN port.
Figure 9:
ground point (Figure 10).
CAUTION: The T610 AP includes one 12mm stainless steel M6x1
earth ground screw with split lock and flat washers. Make sure
that any replacement screw is no longer than 12mm. If a screw is
longer than 12mm, it can damage the AP chassis.
Figure 10:
Connect good earth ground to AP here
Attaching the AP bracket to the AP
Set the azimuth required by the AP.
Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).
Continue with Step 5: Attach the AP bracket to the linkage
bracket.
STEP 5: ATTACH THE AP BRACKET TO THE LINKAGE
BRACKET
Attach the AP bracket to the linkage bracket using the included bolt,
nut, lock washer, flat washer, serrated external-tooth washer shown in
Figure 8.
The AP bracket attaches to the linkage bracket using an M8 bolt and
washer set. The linkage bracket is symmetrical, and either end can be
attached to the AP bracket.
NOTE: Make sure that linkage bracket is installed with its serrated
external-tooth lock washer on the inside of the AP bracket flanges.
This ensures that the elevation adjustment does not change.
As described in Step 4: Mounting the Linkage Bracket to the
U-Joint Bracket, loosely assemble the AP bracket (shown in
Figure 9), the linkage bracket (A in Figure 7), the second
serrated external-tooth lock washer (B in Figure 7), and the
second M8 bolt and washer set (D in Figure 7).
Figure 8:
Attach the linkage bracket to the AP bracket
STEP 9: INSTALLING THE SECURITY CABLE
Use four 0.5-inch x 0.250-28 hex bolts with split lock and flat
washer sets to mount the AP bracket to the AP. Tighten the bolts
to 2.5-3.0 N.m or 22-27 in-lbs.
CAUTION: Make sure that the screws are no longer than 0.5 inch.
If a screw is longer than 0.5 inch, it can damage the AP chassis.
If required, suspend the AP by attaching a carabiner to the
hoisting loop on the AP bracket.
NOTE: The security cable is an optional accessory that must be
purchased separately.
1 Thread the security cable through the mounting bracket (A) and
through the eye on the cable itself (B), as shown in Figure 11.
2 Attach the safety cable to the AP (C) in Figure 11.
Figure 11:
Attaching the security cable
NOTE: This kit may include extra screws, nuts and washers. You
may use the extras wherever required.
4 Continue with Step 7: Set the Elevation and Tighten Elevation
Bolt.
STEP 7: SET THE ELEVATION AND TIGHTEN ELEVATION BOLT
Set the elevation required by the AP.
Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).
STEP 8: EARTH GROUNDING THE AP
CAUTION: Make sure that earth grounding is available and that it
meets local and national electrical codes. For additional lightning
protection, use lightning rods and lightning arrestors.
NOTE: The color coding of ground wires varies by region. Before
completing this step, check your local wiring standards for
guidance.
• Using the factory-supplied ground wire and ground screw/
washer set, connect a good earth ground to the AP chassis
Copyright © 2016 Ruckus Wireless, Inc.
Published June 2016, Part Number 800-71230-001 Rev A
Congratulations! You have mounted your T610 access point.
Page 3 of 4
INSTALLING A USB DONGLE
To install a USB dongle, which could be an IoT radio like BLE,
802.15.4, Z-wave or the like, remove the two 3mm hex screws,
remove the cap, and insert the dongle into the USB port. Once
installed, replace the cap and the hex screws, and torque the screws
to 7 in-lbs.
Figure 12:
Installing a USB dongle
TROUBLESHOOTING
CAUTION: If required, you can reset the AP to its factory default
settings by pressing the reset button located inside the PoE IN
port. DO NOT DO THIS UNLESS SO INSTRUCTED. (Doing this
resets the AP IP address to 192.168.0.1.)
NOTE: After a reset, you can access the internal AP web interface
using https://192.168.0.1. Your device must use any
other address from 192.168.0.2 through 192.168.0.254, with
subnet mask 255.255.255.0. The username is super, and the
password is sp-admin. Refer to the ZoneFlex Outdoor Access
Point User Guide for information on configuring and operating the
AP. This document is available at https://
support.ruckuswireless.com.
NOTE: After an AP is removed from its mounting, it may drip
some water from the channel surrounding the radome. As long as
the AP has been operating normally, this incidental water
collection and dripping is normal, and is not service-affecting.
Copyright © 2016 Ruckus Wireless, Inc.
Published June 2016, Part Number 800-71230-001 Rev A
Page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Language                        : en
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : 
Description                     : 
Title                           : 
Create Date                     : 2007:02:21 14:03:02Z
Creator Tool                    : FrameMaker 11.0.2
Modify Date                     : 2016:06:24 09:38:43-07:00
Metadata Date                   : 2016:06:24 09:38:43-07:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:a47c1bde-ab72-43f5-904d-c3d80b592845
Instance ID                     : uuid:9219f04c-8da9-4583-a310-65b7f782515e
Page Mode                       : UseOutlines
Page Count                      : 4
Subject                         : 
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools