Ruckus Brocade FCX Series Hardware Installation Guide Fast Iron CX Fastiron Installguide

2017-06-15

• Brocade FCX Series Hardware Installation Guide
  • Preface
    • Document conventions
      • Notes, cautions, and warnings
      • Text formatting conventions
      • Command syntax conventions
    • Brocade resources
    • Document feedback
    • Contacting Brocade Technical Support
      • Brocade customers
      • Brocade OEM customers
  • About This Document
    • What’s new in this document
    • Supported Software
  • Product Overview
    • Hardware features
      • Control features
        • Serial management interface (DB-9 Console port)
        • Out-of-band RJ-45 management interface
        • Network interfaces for Brocade FCX 624S, FCX 648S, FCX 624S-F, FCX 624S-HPOE, and FCX 648S-HPOE
        • Network interfaces for Brocade FCX 624-E, FCX 624-I, FCX 648-E, and FCX 648-I
          • FastIron CX 10/100/1000 BASE-T ports
          • Combination ports
          • Slot locations
          • Slot designations
        • SFP interfaces
        • Optional two-port 10 Gbps XFP uplink module
        • Optional 4x1G SFP+ and 4x10G SFP+ modules
        • 16/10 Gbps Ethernet CX4 stacking module
          • Cable specifications for CX4 stacking ports
        • Optional 2-port 10 Gbps SFP+ uplink module
        • Specifying a port address
          • Specifying a data port
          • Specifying a stacking port
          • Specifying a management port
        • –Port, system, and power status LEDs for Brocade FCX 624S, FCX 648S, FCX 624S-F, FCX 624S-HPOE, and FCX 648S-HPOE
        • Port, system, and power status LEDs for Brocade FCX 624-E, FCX 624-I, FCX 648-E, and FCX 648-I
      • Power supplies
        • Power supply unit operation
        • HPOE and HPOE + power supplies
  • Installing the FCX Switch
    • Unpacking the device
      • Package contents
      • General requirements
    • Installation tasks
    • Installation precautions
      • General precautions
      • Lifting precautions
      • Power precautions
    • Preparing the installation site
      • Cabling infrastructure
      • Installation location
      • Installing the device
      • Desktop installation
      • Rack mount installation
    • Connecting devices in a traditional stack
      • Stacking ports
      • Stacking configuration requirements
      • Stacking cables
      • Stack size
      • Stacking topologies
      • Extended distance stacking
    • Powering on the system
    • Attaching a PC or terminal
      • Wiring map for serial cable
    • Installing and replacing a power supply unit
    • Installing or replacing fan trays
    • Installing an optional module
      • Optional 2-port 10 Gbps SFP+ uplink module
  • Checking Network Devices and Testing Connectivity
    • Assigning permanent passwords
      • Setting passwords
      • Recovering from a lost password
    • Configuring IP addresses
      • Devices running Layer 2 software
      • Devices running Layer 3 software
        • Configuring IP parameters for devices running Layer 3 software
          • Configuring IP addresses
          • Assigning an IP address to an Ethernet port
          • Assigning an IP address to a loopback interface
          • Assigning an IP address to a virtual routing interface
        • Deleting an IP address
      • Performing a factory reset
      • Connecting network devices
      • Connectors
      • Cable specifications
      • Cable specifications
      • Connecting to Ethernet or Fast Ethernet hubs
      • Connecting to workstations, servers, or routers
        • Automatic MDI or MDIX detection
      • Connecting a network device to a fiber port
        • Fiber-optic transceivers
        • Installing a transceiver
        • Cabling a fiber-optic transceiver
        • Cleaning the fiber-optic connectors
    • Testing connectivity
      • Pinging an IP address
      • Observing LEDs
      • Tracing a route
    • Troubleshooting network connections
      • Digital optical monitoring
      • Virtual cable testing
        • Virtual Cable Testing configuration notes
        • Virtual Cable Test command syntax
        • Viewing the results of the cable analysis
  • Managing the FCX Hardware
    • Managing temperature settings
      • Using the temperature sensor
        • Displaying the temperature
        • Displaying Syslog messages for temperature
        • Changing temperature warning and shutdown levels
        • Changing the shutdown temperature
        • Changing the temperature polling interval
      • Removing MAC address entries
    • Displaying FCX CPU usage
    • Hardware maintenance schedule
    • Replacing a copper or fiber optic module
      • Removing a copper or fiber optic module
      • Cabling a fiber optic module
      • Cleaning the fiber optic connectors
  • Brocade FCX Series Technical Specifications
    • System specifications
    • Ethernet
    • LEDs
    • Other
    • Weight and physical dimensions
    • Environmental requirements
    • Power supply specifications (per PSU)
    • Power consumption (maximum configuration)
    • Data port specifications (Ethernet)
    • Serial port specifications (DB9)
    • Serial port specifications (pinout RJ-45)
    • Serial port specifications (protocol)
    • Regulatory compliance (EMC)
    • Regulatory compliance (safety)
    • Regulatory compliance (environmental)
  • Troubleshooting
    • Diagnosing switch indicators
      • Power and cooling problems
      • Installation
      • In-band access
  • Regulatory Statements
    • CE Statement
    • China ROHS
    • BSMI statement (Taiwan)
    • Canadian requirements
    • China CC statement
    • Europe and Australia (CISPR 22 Class A Warning)
    • FCC warning (US only)
    • Germany
    • KCC statement (Republic of Korea)
    • VCCI statement
  • Cautions and Danger Notices
    • Cautions
      • General cautions
      • Electrical cautions
    • Danger Notices
      • General dangers
      • Electrical dangers
      • Dangers related to equipment weight
      • Laser dangers