Runco Cl 810 Ultra Cinewide Sdc 1 Users Manual
CL-810 CL-810 Ultra Cl-810 CineWide CL-810 SDC-1 to the manual 8d02fd75-624c-409e-97cc-51828faf0b0c
2015-02-06
: Runco Runco-Cl-810-Cl-810-Ultra-Cl-810-Cinewide-Cl-810-Sdc-1-Users-Manual-525786 runco-cl-810-cl-810-ultra-cl-810-cinewide-cl-810-sdc-1-users-manual-525786 runco pdf
Open the PDF directly: View PDF .
Page Count: 1
Download | ![]() |
Open PDF In Browser | View PDF |
O W N E R ’S O P E R A T I N G M A N U A L CL-810 Series Digital Light ProcessingTM Projectors CL-810 CL-810 Ultra Cl-810 CineWide CL-810 / SDC-1 TWO YEAR LIMITED WARRANTY For Projectors, Video Processors and Controllers Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces “The World’s Finest Home Theater Products.” With proper installation, setup and care, you should enjoy many years of unparalleled video performance. This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents. Y WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY: EL IM IN A R SERVICE LABOR: Runco will pay for service labor by Runco Authorized Service Center when needed as a result of manufacturing defect for a period of two (2) years from the effective date of delivery to the end user (excluding the lamp). PARTS: (Not including the lamp) Runco will provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of two (2) years from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period. PROJECTOR LAMP: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a manufacturing defect for a period of six (6) months or 1000 hours, which ever comes first, from the effective date of delivery to the end user. In addition, Runco will provide a new or rebuilt replacement lamp for the lamp that fails due to defects in materials or workmanship for a period of six (6) months or 1000 hours, which ever comes first, from the effective date of delivery to the end user. Such replacement lamps are then subsequently warranted for the remaining portion (if any) of the original warranty period. WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY: PR This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this Limited Warranty. CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. RIGHTS, LIMITS AND EXCLUSIONS: Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. Runco CL-810 Series Owner’s Operating Manual iii EFFECTIVE WARRANTY DATE: This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date. IMPORTANT -- WARRANTY REGISTRATION: Y Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified. EL IM IN A R CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE: Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of the product, during usual working hours, providing location of product is within normal operating distance from a Runco Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco Dealer. If this is not possible, contact Runco directly for a Return Authorization number and shipping instructions. Runco will return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the responsibility of the owner. COPYRIGHT AND TRADEMARKS: PR © Copyright 2006 Runco International. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. All trademarks and registered trademarks are the property of their respective owners. iv Runco CL-810 Series Owner’s Operating Manual ADDITIONAL INFORMATION: To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this Limited Warranty, please call or write: EL IM IN A R Y RUNCO INTERNATIONAL, INC. Attn: Customer Service Department 2900 Faber Street Union City, CA 94587 Ph: (510) 324-7777 Fax: (510) 324-9300 Toll Free: (800) 23-RUNCO RUNCO VIDEO-PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS _________________________________________________________ ________________________________________ Model Purchased Date Serial Number PR ____________________________________________________________________________________________________________ ____________________________________________________________________________________________________________ Runco Authorized Dealer Name ____________________________________________________________________________________________________________ Address ____________________________________________ __________________ ________________________ City State/Province Postal Code ____________________________________________ _______________________________________________________ Phone Fax Runco CL-810 Series Owner’s Operating Manual v Safety Precautions Thank you for your purchase of this quality Runco video projector! It has been designed to provide you with the quality of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. EL IM IN A R CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Y CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Do not use this equipment near water, outdoors or otherwise exposed to the elements. 5. Clean only with a dry cloth. 6. Do not block any ventilation openings. PR 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet. 9. The 12V trigger only outputs DC 12V signal for triggering. Do not connect to any other power input or output. This could cause damage to this unit. 10. Only use accessories specified by Runco International. 11. Keep the packing material in case the equipment should ever need to be shipped. 12. Unplug this projector during lightning storms or when it will not be used for an extended period of time. 13. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond rated life could cause them to explode in rare occasions. 14. Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any way, objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not operate normally, or has been dropped. vi Runco CL-810 Series Owner’s Operating Manual 1 Table of Contents TWO YEAR LIMITED WARRANTY ................................................................................. iii Safety Precautions ......................................................................................................... vi 1. Introduction ...............................................................................................................1 About This Manual .......................................................................................................1 Y Target Audience .....................................................................................................1 EL IM IN A R If You Have Comments About This Manual... ..........................................................1 Textual and Graphic Conventions ...........................................................................1 Using This Manual ........................................................................................................2 Related Documents ......................................................................................................2 Description, Features and Benefits ...............................................................................3 Key Features and Benefits ......................................................................................4 Parts List ................................................................................................................4 2. Controls and Functions ............................................................................................5 CL-810 at a Glance ......................................................................................................5 CL-810 Rear Panel .......................................................................................................7 CL-810 Remote Control ...............................................................................................9 PR 3. Installation ...............................................................................................................13 Remote Control ..........................................................................................................13 Notes on Batteries ................................................................................................13 Notes on Remote Control Operation .....................................................................13 Quick Setup ...............................................................................................................14 Installation Considerations ..........................................................................................15 Installation Type ....................................................................................................15 Ambient Light .......................................................................................................15 Throw Distance.....................................................................................................16 Vertical and Horizontal Position.............................................................................18 Vertical and Horizontal Lens Shift..........................................................................18 Folded Optics .......................................................................................................21 Other Considerations ............................................................................................21 Installing the Optional CineWide Lens .........................................................................21 Runco CL-810 Series Owner’s Operating Manual vii Mounting the CL-810 .................................................................................................22 Floor Mounting......................................................................................................22 Ceiling Mounting ...................................................................................................22 Adjusting the Projector Height or Projection Angle ................................................22 Connections to the CL-810 ........................................................................................23 Connector Panel Access.......................................................................................23 Connecting the SDC-1 System Expansion Device to the CL-810..........................23 Connecting Source Components to the CL-810 ...................................................24 Y RS-232 Controller Connection ..............................................................................27 Connecting 12-Volt Trigger Output to External Theater Components ....................28 EL IM IN A R Connecting to AC Power ......................................................................................28 4. Operation .................................................................................................................29 Turning on the Power .................................................................................................29 Changing the OSD Language .....................................................................................29 Adjusting the Picture Orientation ................................................................................29 Lens Adjustments ......................................................................................................30 Focus ...................................................................................................................30 Zoom....................................................................................................................30 Vertical and Horizontal Lens Shift..........................................................................30 Selecting Video Memory .............................................................................................30 PR Selecting an Aspect Ratio ..........................................................................................30 Adjusting the Picture ..................................................................................................30 Selecting An Input Source ..........................................................................................31 Using Picture-In-Picture/Picture-By-Picture (PIP/PBP) ................................................31 Using the On-Screen Menus ......................................................................................31 Main Menu............................................................................................................33 Picture Adjustment ..............................................................................................33 Aspect Ratio ........................................................................................................38 Installation.............................................................................................................40 Option ..................................................................................................................41 Set Up ..................................................................................................................42 ISF Calibration ......................................................................................................46 5. Maintenance and Troubleshooting ........................................................................49 Lamp Replacement ....................................................................................................49 Troubleshooting Tips ..................................................................................................50 viii Runco CL-810 Series Owner’s Operating Manual 6. Serial Communications ..........................................................................................53 RS-232 Connection and Port Configuration ...............................................................53 Serial Command Syntax .............................................................................................53 7. Specifications ..........................................................................................................57 CL-810 Specifications ................................................................................................57 CL-810 Dimensions ...................................................................................................60 PR EL IM IN A R Y CL-810 Ultra Dimensions ...........................................................................................61 Runco CL-810 Series Owner’s Operating Manual ix PR EL IM IN A R Y Notes: x Runco CL-810 Series Owner’s Operating Manual 1 List of Figures 2-1. CL-810 Front/Side/Top View ........................................................................................5 2-2. CL-810 Rear/Bottom/Side View ...................................................................................6 2-3. CL-810 Rear Panel.......................................................................................................7 2-4. CL-810 Remote Control ...............................................................................................9 3-1. Estimating Throw Distance .........................................................................................16 3-2. Projector Placement ...................................................................................................18 3-3. Vertical Lens Shift.......................................................................................................18 3-4. Horizontal Lens Shift...................................................................................................19 3-5. Folded Optics.............................................................................................................21 3-6. Connecting the CL-810 to the SDC-1 ........................................................................23 3-7. HDMI/DVI Source Connections ..................................................................................24 3-8. RGB Connections ......................................................................................................25 3-9. Progressive Component Video Connections...............................................................25 3-10. Composite, S-Video and Component Video Connections.........................................26 3-11. RS-232 Control System Connection.........................................................................27 3-12. Connecting 12-Volt Trigger Outputs .........................................................................28 4-1. CL-810 OSD Menu Structure .....................................................................................32 4-2. Typical PLUGE Pattern for Adjusting Brightness .........................................................34 4-3. Typical Gray Bar Pattern for Adjusting Contrast ..........................................................35 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint................................35 4-5. Typical Test Pattern for Adjusting Sharpness..............................................................37 7-1. CL-810 Dimensions....................................................................................................60 7-2. CL-810 Ultra Dimensions ...........................................................................................61 Runco CL-810 Series Owner’s Operating Manual xi List of Figures Notes: xii Runco CL-810 Series Owner’s Operating Manual 1 This Owner’s Manual describes how to install, set up and operate the Runco CL-810 Series Digital Light Processing (DLP™) Projectors. This product family consists of the CL-810 and the CL-810 Ultra Projectors, each of which are available with a variety of optional upgrades. Introduction 1.1 About This Manual EL IM IN A R Y Throughout this manual, the Runco CL-810 Series DLP Projectors are referred to collectively as the “CL-810.” Except where noted, the features and functions described in this manual are common to all versions of this product. Runco has prepared this manual to help home theater installers and end users get the most out of the CL-810. Target Audience Runco has made every effort to ensure that this manual is accurate as of the date it was printed. However, because of ongoing product improvements and customer feedback, it may require updating from time to time. You can always find the latest version of this and other Runco product manuals on-line, at www.runco.com. Runco welcomes your comments about this manual. Send them to techpub@runco.com. If You Have Comments About This Manual... Text Conventions: The following conventions are used in this manual, in order to clarify the information and instructions provided: Textual and Graphic Conventions PR • Remote and built-in keypad button identifiers are set in upper-case bold type; for example, “Press EXIT to return to the previous menu.” • All keys with functional names are initial-capped, set in bold type and enclosed in angle brackets. These keys are the following:, , , and . • indicates that you may press either the RETURN or ENTER key on your keyboard if it has both keys. • Computer input (commands you type) and output (responses that appear on-screen) is shown in monospace (fixed-width) type; for example: “To change the aspect ratio to Letterbox, type x063x .” In addition to these conventions, underlining, boldface and/or italics are occasionally used to highlight important information, as in this example: Note A carriage return must be used after each command or string. Runco CL-810 Series Owner’s Operating Manual 1 Introduction Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury: TIPS highlight time-saving short cuts and helpful guidelines for using certain features. NOTES emphasize text with unusual importance or special significance. They also provide supplemental information. EL IM IN A R Y CAUTIONS alert users that a given action or omitted action can degrade performance or cause a malfunction. WARNINGS appear when a given action or omitted action can result in damage to the equipment, or possible non-fatal injury to the user. DANGER appears when a given action can cause severe injury or death. Use the following table to locate the specific information you need in this manual. PR 1.2 Using This Manual 1.3 Related Documents The following are related Runco documents: • Runco SDC-1 System Expansion Device Owner’s Operating Manual 2 Runco CL-810 Series Owner’s Operating Manual Introduction The CL-810 Series DLP Projectors offer the astounding picture quality and versatility heretofore associated with more expensive projectors. Their 1280 x 720 native resolution DLP light engine features Runco's powerful SuperOnyx™ technology for bright, pristine high-definition images. Contrast ratio and dynamic range extend to new heights with Runco's exclusive Reflectance Volume Regulation™ (RVR), an electronically-controlled iris system. EL IM IN A R Y The CL-810 is equipped with a precision optics package offering a power zoom control and a throw range of 1.80:1 to 2.43:1. The CL-810 Ultra provides even greater installation flexibility, with six lens options from which to choose offering throw distances ranging from 1.22:1 to 5.68:1. For rear-projection applications, a fixed, short-throw lens is also available with the CL-810 Ultra. The CL-810's illumination system incorporates Runco's exclusive Selectable Lamp Intensity Control™ (SLIC™), which provides two light intensity levels to allow maximum flexibility for screen size, ambient light conditions, brightness and contrast balance, and lamp life preservation. It also has a newly refined cooling system, which increases efficiency and reduces noise levels. The CL-810 has been engineered to comply with Imaging Science Foundation™ (ISF) standards for maximum home theater image quality. Runco's sophisticated parameters for white balance and color gamut control have also been implemented for precise balance of gray scale and color. The CL-810 incorporates Runco-proprietary de-interlacing technology that provides exceptional scaling and film-to-video (3:2 pulldown) conversion for the most artifact-free images possible. PR For uncompromising widescreen reproduction of movies originally filmed in the “scope” (2.35:1) format, the CL-810 can be equipped with Runco’s CineWide™ technology, a combination of software, electronics and high-quality anamorphic optics. CineWide maintains constant vertical height on the screen just as in a movie theater. When a viewer transitions from 1.78:1 (16:9) program material to 2.35:1, the image simply gets wider while full height is maintained. Also available with the CL-810 Ultra is CineWide with AutoScope™, an enhanced, remote-controlled motorized version of CineWide. The CL-810 is available with or without the SDC-1, a versatile, high-performance digital video switcher. By providing a single, convenient connection point for home theater components that is separate from the projector, the SDC-1 gives designers and installers greater flexibility in terms of projector placement. It also simplifies the task of adding components after the projector has been installed. Discrete IR and RS-232 control make custom installation seamless, while discrete source and aspect ratio selection accommodate any automation control system. Runco CL-810 Series Owner’s Operating Manual 3 1.4 Description, Features and Benefits Introduction Key Features and Benefits ➤ The CL-810 offers these key features and benefits: • Native Resolution: 1280 x 720 (16:9 Native Aspect Ratio) • DLP system using SuperOnyx™ Digital Micromirror Device (DMD) • 8-segment, 5x color wheel produces wide dynamic range and rich grayscale • Reflectance Volume Regulation (RVR™) provides for infinitely variable adjustment of the light path through the optics, enabling the perfect balance of black and white levels for each individual installation • Picture in Picture / Picture by Picture functions allow you to display two inputs on the screen at the same time • HDMI Input with High-bandwidth Digital Content Protection (HDCP) Y • HDTV Compatible EL IM IN A R • CinOptx™ Proteus lens options for stunning sharpness and throw distance flexibility (CL-810 Ultra only) Parts List ➤ Your CL-810 is shipped with the following items. If any items are missing or damaged, please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO. • CL-810 or CL-810 Ultra DLP Projector • Remote Control Unit and two (2), AAA-size batteries • AC Power Cords (North America, Europe, Asia) • Source Connection Cables: • Composite Video • S-Video • Component Video • RGB (DB15HD-to-5 x BNC) PR • HDMI to HDMI • HDMI to DVI • (1) Warranty information and registration card • Runco CL-810 Series Owner’s Operating Manual (this document) Optional Accessories - CL-810 and CL-810 Ultra: • CineWide™ technology (fixed, secondary anamorphic lens) • SDC-1 System Expansion Device • Ceiling mount kit Optional Accessories - CL-810 Ultra Only: • CinOptx™ Proteus lens options • CineWide™ with AutoScope™ system (secondary anamorphic lens and motorized mount) 4 Runco CL-810 Series Owner’s Operating Manual 2. Controls and Functions 2.1 CL-810 at a Glance PR EL IM IN A R Y Figure 2-1 and Figure 2-2 show the key CL-810 components. Figure 2-1. CL-810 Front/Side/Top View 1. RUNCO LOGO The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or urighTo rotte thlogo, grip it at tsides, puitay from thprojector an rotate it 180 degrees. 2. PROJECTION LENS 3. TOP IR SENSOR 4. TEMP LED Intefaus an teure as follows: • Off during normal operation • Red when internal temperature is too high • Flashes red when the fans are not working or the lamp cover is open 5. INTAKE VENT Runco CL-810 Series Owner’s Operating Manual 5 Controls and Functions 6. POWER/STANDBY LED Indicates power status as follows: • Orange when the projector is in standby mode • Flashes orange for 45 seconds after the projector is turned on to indicate that the lamp is warming up • Green during normal operation • Flashes green for 110 seconds after the projector is turned off to indicate that the lamp is cooling down • Off during normal operation Y 7. LAMP LED Indicates lamp status as follows: EL IM IN A R • Red when the lamp has exceeded its usage life or developed a problem. • Flashes red when the fans are not working or the lamp cover is open 8. EXHAUST VENT PR 9. FRONT IR SENSOR Figure 2-2. CL-810 Rear/Bottom/Side View 1. RUNCO LOGO The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or upright. To rotate the logo, grip it at the sides, pull it away from the projector and rotate it 180 degrees. 2. CABLE OPENING Pass cables through this opening. 3. CABLE ACCESS DOOR Open to access connectors. 6 Runco CL-810 Series Owner’s Operating Manual Controls and Functions 4. LAMP MODULE COVER Remove this cover to access the lamp compartment. 5. FRONT/REAR ADJUSTERS Use these to adjust the projector height or projection angle. 6. CEILING MOUNT HOLES Use these to attach the ceiling bracket to the projector. 2.2 CL-810 Rear Panel PR EL IM IN A R Y Figure 2-3 shows the CL-810 rear panel. Figure 2-3. CL-810 Rear Panel 1. HDMI (Digital) HDCP-compliant digital video input for connecting a DVD player or HD tuner with a DVI or HDMI output. 2. SDC-1 R-LinkTM Input (CL-810/SDC-1 and CL-810 Ultra/SDC-1 only) DVI-style connector for connecting the SDC-1 System Expansion Device output to a CL-810 or CL-810 Ultra equipped with this connector. (Connect your sources to the SDC-1 inputs.) Runco CL-810 Series Owner’s Operating Manual 7 Controls and Functions 3. COMP 1 (RCA connectors) Standard Definition (480i/576i) Component (YPrPb) input. This is the input for component video from sources such as DVD players. Tip For best results, do not run your DVD player in progressive mode. 4. COMPOSITE VIDEO INPUT Standard composite video input for connecting a VCR, laser disc player or other composite video source. EL IM IN A R Y 5. S-VIDEO A standard S-Video input for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR. 6. POWER INPUT (100 to 240 VAC) Connect the CL-810 to power here. 7. MAIN POWER SWITCH Disconnects or applies power to the CL-810. 8. RS-232 CONTROL PORT A female, RJ-11 connector for interfacing with a PC or home theater automation/control system. 9. 12-VOLT (250 mA) TRIGGER OUTPUT(3.5-mm, mini phono jack) Connection for a 12-volt trigger-controlled device. This can be a retractable screen, screen mask or the Runco CineWide with AutoScope system. PR 10. COMP 2 / RGB Five, BNC connectors for connecting either RGB or component (YPbPr) high-definition television signals. (The CL-810 automatically detects the signal format.) 8 Runco CL-810 Series Owner’s Operating Manual Controls and Functions Figure 2-4 shows the CL-810 remote control, and the paragraphs that follow describe its functionality. LIGHT VID ON 2 OFF S-VID COMP1 RGBHD HDMI COMP2 INFO 4 RVR ENTER EXIT BRT 6 EL IM IN A R 3 MENU CONT COL TNT ISF NIGHT ISF DAY FACT 4X3 LBOX VWIDE 1 2 VCINE 4 5 6 7 8 9 0 PBP ACT PIP PIP+ FOCUS FOCUS ZOOM ZOOM LENS LENS PIP- MEM1 ANA 16X9 5 7 CINEMA 10 PR 3 8 Y 1 9 Figure 2-4. CL-810 Remote Control Runco CL-810 Series Owner’s Operating Manual 9 2.3 CL-810 Remote Control Controls and Functions 1. LIGHT Press to illuminate the buttons. 2. ON / OFF Use these buttons to turn the projector on or off. 3. Source Selection Buttons: VID Press to select Composite video input as the source. Y S-VID (S-Video) Press to select the S-Video input as the source. EL IM IN A R COMP1 (SD Component) Press to select Component 1 (SD 480i/576i) video input as the source. COMP2 (HD Component) Press to select Component 2 (HD 480p/576p/720p/1080i) video input as the source. RGBHD Press to select the Component 2 RGB input. HDMI Press to select the HDMI input. 4. INFO Displays active source and aspect ratio information. PR Cursor Keys ( , , , ) Use these buttons to select items or settings, adjust settings or switch display patterns. RVR (Reflectance Volume Regulation) Adjusts the lens aperture (iris) setting according to the ambient light level in the viewing area. EXIT Press to save menu item setting(s), exit the current menu and return to the previous one. ENTER Press to select a highlighted menu item or confirm a changed setting. MENU Press this button to show or hide the on-screen display (OSD) controls. 10 Runco CL-810 Series Owner’s Operating Manual Controls and Functions 5. Picture Adjustment Buttons: BRT (Brightness) Press to adjust black level. CONT (Contrast) Press to adjust white level. COL (Color) Press to adjust color intensity. Y TNT (Tint) Press to adjust color hues. EL IM IN A R 6. Memory Preset Buttons: MEM1 Press to recall settings for the current input from the “Memory 1” memory preset. ISF NIGHT Press to recall settings for the current input from the “ISF Night” memory preset. ISF DAY Press to recall settings for the current input from the “ISF Day” memory preset. FACT Press to recall the factory-default settings for the current input. 7. Aspect Ratio Selection Buttons Use these buttons to select an aspect ratio directly, as follows: PR ANA 16:9 (Anamorphic) For viewing 16:9 DVDs or HDTV programs in their native aspect ratio. 4X3 (Standard 4:3) Scales the input signal to fit 4:3 display mode in the center of the screen. LBOX (Letterbox) For viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen. VWIDE (VirtualWide) Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display. CINEMA For viewing 2.35:1 source material on a 1.78:1 (16:9) screen. The upper and lower portions are masked. VCINE (CineWide-equipped projectors only) Selects the Virtual Cinema aspect ratio, which anamorphically compresses a 2.35:1 image to fill a 16:9 image area. (The secondary anamorphic lens then “stretches” the image back to 2.35:1.) 8. 0 - 9 Use these keys to enter menu passcodes. Runco CL-810 Series Owner’s Operating Manual 11 Controls and Functions 9. Picture-In-Picture (PIP) / Picture-By-Picture (PBP) Controls: Note PIP and PBP are not available when the CL-810 is used with the SDC-1 System Expansion Device. PBP Press to activate PBP mode. EL IM IN A R PIP Press to activate PIP mode. Y ACT Press to switch to the active window in PIP or PBP mode. PIP+ Press to enlarge the PIP window. PIPPress to shrink the size of the PIP window. 10. Motorized Lens Controls: FOCUS Press to focus the image. ZOOM Press to reduce or enlarge the projected image size. PR LENS Press to access the lens shift controls. 12 Runco CL-810 Series Owner’s Operating Manual Installation 3 3.1 Remote Control EL IM IN A R Y To install batteries in the remote control, push the battery cover and slide it off. Install the two AAA batteries with the correct polarity and then replace the cover. • Make sure that the battery polarities are correct when installing the batteries. Notes on Batteries • Do not mix an old battery with a new one or different types of batteries. • If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage. • Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector. • If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones. PR • The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. • Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the projector, and repeat the operation. • The Ø icon appears on the screen when you press a button for an unavailable function. Runco CL-810 Series Owner’s Operating Manual 13 Notes on Remote Control Operation Installation 3.2 Quick Setup Table 3-1 gives a quick overview of the CL-810 installation process. The sections following this one provide detailed instructions. Note Installation should be performed by a qualified custom video installation specialist. Y Table 3-1. Installation Overview Procedure PR EL IM IN A R Step For Details, Refer to page... 1 Choose a location for the projector 15 2 Install the CineWide (secondary anamorphic) lens (optional) 21 3 Mount the projector 22 24 4 If installing with an SDC-1, connect ONLY the SDC-1 output to the CL-810 and make all other connections to the SDC-1; continue with Step 7 -- OR -If installing without an SDC-1, connect signal sources to the CL-810 and continue with Step 5 5 Connect external controller to RS-232 port (optional) 27 6 Connect other home theater components to 12-volt trigger outputs (optional) 28 7 Apply power to the projector 28, 29 8 Change the OSD Language (optional) 29 9 For rear-screen and/or ceiling-mount installations, select the proper picture orientation 29 10 Lens adjustments: projected image size (zoom), position (shift) and focus 18, 30 38 through 43 11 Projector calibration: adjust the following for each input, starting with Component 1; save settings when finished: • Aspect ratio • Brightness • Contrast • Color level • Tint • Input position 14 Runco CL-810 Series Owner’s Operating Manual Installation Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally. 3.3 Installation Considerations Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount. Table 3-2 compares these various installation methods. Installation Type Advantages Considerations EL IM IN A R Front Screen, Floor Mount Installation Y Table 3-2. Projector Installation Options • Easy to set up • Can be moved or changed quickly • Easy to access • Shares floor space with audience Front Screen, Inverted Mount (ceiling) Installation • Does not take up audience space • Projector is unobtrusive • Projector cannot be accidentally moved • Installation is more permanent • Projector access is more difficult Rear Screen, Floor Mount Installation • Projector is completely hidden • Projector is easily accessed • Usually good ambient light rejection • Requires separate room • Installation cost is usually higher Rear Screen, Inverted Mount (ceiling) Installation PR • Projector is completely hidden • Usually good ambient light rejection • Requires separate room • Installation cost is usually higher Rear Screen, Floor Mount with Mirror • Projector is completely hidden • Usually good ambient light rejection • Requires less space behind screen than other rear screen installations • Requires separate room • Installation cost is usually higher In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your images will be noticeably reduced if light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant. Runco CL-810 Series Owner’s Operating Manual 15 Ambient Light Installation Throw Distance ➤ Throw distance is the distance measured from the front of the projector to the screen. This is an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be the right size for your screen. You can quickly estimate the throw distance by taking the width of the screen and multiplying it by the lens throw ratio; see Figure 3-1. The result of this calculation tells you roughly how far back the projector should be positioned from the screen in order to project a focused image large enough to fill the screen. Scr een EL IM IN A R CL-810 Throw Ratio: 1.80 to 2.43 CL-810 Ultra Throw Ratio: refer to Table 3-3 Y Estimating Throw Distance Throw Distance (TD) = Screen Width (w) x Lens Throw Ratio wid th ( w) TD PR Figure 3-1. Estimating Throw Distance 16 Runco CL-810 Series Owner’s Operating Manual Installation Throw Ratio - CL-810 Ultra: Table 3-3 lists the available lens options for the CL-810 Ultra and their associated throw ratios. Table 3-3. CL-810 Ultra Lens Options Lens Option (Note 2) Proteus A Throw Ratio (Throw Dist. ÷ Screen Width) Minimum Maximum For rear-screen installations only. Contact Runco Technical Support for more information. 1.22 - 1.44 122 144 Proteus C 1.45 - 1.75 145 175 Proteus D Proteus D with CineWide Proteus E Proteus E with CineWide Proteus F Proteus F with CineWide Notes: Y Proteus B EL IM IN A R 0.67 (Fixed) Throw Distance Range (in inches, with 100-inch Wide Screen) 1.82 - 2.38 182 238 1.38 - 1.79 138 179 2.42 - 3.57 242 357 1.84 - 2.70 184 270 3.65 - 5.68 365 568 2.77 - 4.29 277 429 1. Throw distance does not affect image quality, provided these ranges are taken into account. 2. Only the Proteus D, E and F lenses can be used with the optional CineWide (secondary anamorphic) lens. Doing so affects the throw distances as shown here. PR Throw Ratio - CL-810: The CL-810 offers a throw ratio of between 1.80 and 2.43. Throw Ratio - CL-810 CineWide: The CineWide version of the CL-810 also offers a throw ratio of between 1.80 and 2.43. It uses a prismatic-style anamorphic lens that compresses the image height (as opposed to the cylindrical anamorphic lenses used with the CL-810 Ultra, which stretch the image width). Using this lens type does not change the projector throw ratio. Runco CL-810 Series Owner’s Operating Manual 17 Installation Vertical and Horizontal ➤ Position Proper placement of the projector relative to the screen will yield a rectangular, perfectly-centered image that completely fills the screen. Ideally, the projector should be positioned perpendicular to the screen and in such a way that the lens center and screen center are aligned with each other, as shown in Figure 3-2. Ceiling Installation Ceiling Height Projection Distance Lens Center EL IM IN A R Y x Screen Lens Center Floor Installation Screen Height Lens Center Lens Center x Projection Distance Floor Figure 3-2. Projector Placement PR Vertical and Horizontal ➤ Lens Shift If it is not possible to align the projector and screen as shown in Figure 3-2, you can use the lens shift (LENS) controls on the projector remote to center the image on the screen. Lens shift is generally expressed as a percentage of the screen height or width, as shown in Figure 3-3 and Figure 3-4. Screen Center 0% 50% Height Lens Shift (0.5 x H) Base plate to lens center = approx. 5-6" (depending on the amount of lens shift) 100% Height Lens Shift (1.0 x H) 150% Height Lens Shift (1.5 x H) Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens is used in this example. Figure 3-3. Vertical Lens Shift 18 Runco CL-810 Series Owner’s Operating Manual Installation 150% Width Lens Shift (1.5 x W) 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) Screen Center EL IM IN A R Screen Width (W) Y 0% PR Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens is used in this example. Figure 3-4. Horizontal Lens Shift Runco CL-810 Series Owner’s Operating Manual 19 Installation Table 3-4 lists the lens shift limits for each available CL-810 lens, as percentages and absolute measurements with a 100 x 56 inch (1.78:1) screen. Table 3-4. Vertical and Horizontal Lens Shift Limits Lens Option CL-810 CL-810 Ultra -- Proteus Proteus Proteus Proteus Proteus Proteus A B C D E F Lens Shift Limits, as Percentages of Screen Height or Width (Notes 1 and 2) 50% 2% Down 50% 2% 11% 10% 13% 14% 20% 72% 70% 70% 71% 63% Y Up EL IM IN A R Vertical (Note 2) Horizontal (Note 2) Left 0% 0% 13% Right 0% 0% 13% Lens Shift Limits in Inches, with a 100-by-56 inch (1.78:1) Screen Up 28.00 1.12 6.16 5.60 7.28 7.84 11.20 Down 28.00 1.12 40.32 39.20 39.20 39.76 35.28 Left 0 0 13.00 Right 0 0 13.00 Vertical Horizontal Notes: PR 1. With no vertical or horizontal lens shift, the lens center and screen center are aligned with each other. 2. Vertical shift limits are percentages of the screen height. Horizontal shift limits are percentages of the screen width. 3. Vertical lens shift figures apply to ceiling mount configurations. For floor installations (where the projector is upright), reverse the up/down vertical offset percentages. 20 Runco CL-810 Series Owner’s Operating Manual Installation Folded Optics Figure 3-5. Folded Optics EL IM IN A R Y In rear-screen applications where space behind the projector is limited, a mirror may be used to fold the optical path, as shown in Figure 3-5. The position of the projector and mirror must be accurately set. If you are considering this type of installation, contact your dealer for assistance. Other considerations and tips that can help improve your installation: Other Considerations • Keep the ambient temperature constant and below 35°C (95°F). Keep the projector away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the projector circuitry, which may affect performance. • Keep the projector away from devices that radiate electromagnetic energy such as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers and elevators. PR If you are installing a CL-810 or CL-810 Ultra with the optional CineWide or CineWide with AutoScope system, install the secondary anamorphic lens in accordance with the instructions provided with the lens installation kit. Runco CL-810 Series Owner’s Operating Manual 21 3.4 Installing the Optional CineWide Lens Installation 3.5 Mounting the CL-810 There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. In typical front and rear screen installations, the projector can be mounted to a secure and level surface such as a table or cart. Carts are useful when moving a projector during a presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it from being moved during a presentation. Ceiling Mounting ➤ The projector can also be inverted and suspended from the ceiling using a specially-designed ceiling mount fixture. This type of mounting is recommended for fixed installations and for those that want the projector out of sight or have a limited space for projector and audience. EL IM IN A R Y Floor Mounting ➤ Note Adjusting the Projector ➤ Height or Projection Angle Use only the Runco-approved ceiling mount kit designed for your projector. Install the mount kit according to the instructions provided with it. If the screen is significantly higher or lower than the projector, you can also tilt the projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling mount. PR For a floor installation, turn the four adjustable feet on the bottom of the projector to adjust the projector height and/or projection angle. If you do this, you may need to make keystone adjustments or vertically shift the image using the on-screen display (OSD) controls, to compensate. For detailed instructions, refer to Using the On-Screen Menus on page 31. 22 Runco CL-810 Series Owner’s Operating Manual Installation Proceed as follows to connect the CL-810 to your video sources, external controller(s) -- if present -- and AC power. When connecting your equipment: 3.6 Connections to the CL-810 • Turn off all equipment before making any connections. • Use the correct signal cables for each source. • Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Connector Panel Access EL IM IN A R Y To access the connector panel, pull firmly on the cable access cover to open it. If (and ONLY if) your installation includes an SDC-1 System Expansion Device: Use a Runco R-Link cable to connect the SDC-1 output to the CL-810 R-Link input; see Figure 3-6. All signal sources should then be connected to the appropriate inputs on the rear panel of the SDC-1. The signal from the SDC-1 is then output to the CL-810 projector via the R-Link cable. For detailed instructions, refer to the SDC-1 Owner’s Operating Manual. Connect ONLY an SDC-1 to the R-Link input! Although the R-Link looks like a DVI input, it does not function like one and cannot be used as an additional video input. PR Note Figure 3-6. Connecting the CL-810 to the SDC-1 Runco CL-810 Series Owner’s Operating Manual 23 Connecting the SDC-1 System Expansion Device to the CL-810 Installation Connecting Source ➤ Components to the CL-810 If your installation does not include an SDC-1: Connect your video sources to the CL-810 as shown and described in the sections that follow. HDMI/DVI Connections: See Figure 3-7. With an HDMI source, use the included HDMI-to-HDMI cable; with a DVI source, use the included DVI-to-HDMI cable. Use the HDMI input whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the projector. EL IM IN A R Y Tip PR Figure 3-7. HDMI/DVI Source Connections 24 Runco CL-810 Series Owner’s Operating Manual Installation EL IM IN A R Y RGB Connections: Connect your personal computer or other RGB source (DVD player or HD set top box) to the COMP 2/RGB input; see Figure 3-8. You can use the included DB15HD-to-5 x BNC cable if your RGB source has a 15-pin, VGA-type connector. Figure 3-8. RGB Connections PR Progressive Component Video Connections: Connect your progressive component source (DVD player or HD set top box) to the COMP 2/RGB input as shown in Figure 3-9. Figure 3-9. Progressive Component Video Connections Runco CL-810 Series Owner’s Operating Manual 25 Installation PR EL IM IN A R Y Composite/S-Video/Component Video Connections: Use the included cables to connect your composite, S-Video and SD (480i) component video sources to the CL-810 as shown in Figure 3-10. Figure 3-10. Composite, S-Video and Component Video Connections 26 Runco CL-810 Series Owner’s Operating Manual Installation Connect a PC or home theater control/automation system (if present) to the RS-232 port on the CL-810; see Figure 3-11. Use a standard, 4-wire RJ-11 telephone cable, wired straight-through. For more information about using this connection, refer to Serial Communications on page 53. PR EL IM IN A R Y S-VID S-VID / Figure 3-11. RS-232 Control System Connection Runco CL-810 Series Owner’s Operating Manual 27 RS-232 Controller Connection Installation If your CL-810 is equipped with a CineWide with AutoScope system, or if your home theater contains other devices that respond to 12-volt triggers (such as a retractable screen or screen mask), connect it to the 12-volt trigger output as shown in Figure 3-12. EL IM IN A R Y S-VID / S-VID Connecting 12-Volt ➤ Trigger Output to External Theater Components 3.5-mm mini plug to CineWide with AutoScope system or other home theater components (screen, screen mask etc.) Figure 3-12. Connecting 12-Volt Trigger Outputs Connecting to AC Power ➤ The CL-810 ships with various types of AC power cords. Choose the one that is appropriate to your locale. PR Plug the female end of the power cord into the AC receptacle on the rear of the projector (AC 100V ~ 240V). Then, connect the other end to your AC power source. Power switch 28 Runco CL-810 Series Owner’s Operating Manual Operation 4 1. Turn on your source components. 2. Turn on the main power switch at the rear of the projector. The POWER LED lights orange. The LAMP and TEMP LEDs light red briefly, then go out. 4.1 Turning on the Power 4. When the projector is ready for use, the POWER LED lights green. Y 3. Press the ON button on the remote control to turn on the CL-810. The POWER LED flashes orange to indicate that it is warming up. EL IM IN A R 5. “Searching...” appears on the screen before the CL-810 identifies the input signal and remains there until a valid signal is detected. 6. If an incompatible input signal exceeds the range of the projector, a “No signal supported" message appears on the screen. This message remains on the screen until you change the input signal. The CL-810 OSD language is initially set to English, but can also display the menus in French, Spanish, Italian or German. To change the OSD language: 1. Press MENU. 4.2 Changing the OSD Language 2. Select Installation from the Main Menu and press ENTER. 3. Select Language from the Installation Menu and press ENTER. PR 4. Press or to highlight the desired language. (The change takes effect immediately.) By default, the CL-810 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this: 1. Press MENU on the remote control. 2. Select Installation from the Main Menu and press ENTER. 3. Select Picture Orientation from the Installation Menu and press ENTER. 4. Choose Floor Rear, Ceiling Front or Ceiling Rear to match the installation method. Runco CL-810 Series Owner’s Operating Manual 29 4.3 Adjusting the Picture Orientation Operation 4.4 Lens Adjustments The CL-810 gives you a great deal of control over the picture size, position and focus. To access the motorized lens controls, use the FOCUS, ZOOM and LENS buttons on the remote control. ZOOM ZOOM FOCUS FOCUS LENS LENS To focus the projected image, press the FOCUS button, then use the left- and right-arrow buttons to adjust the focus. Zoom ➤ To make the picture smaller (zoom out), press the ZOOM button, then use the left-arrow ( ) button. Y Focus ➤ EL IM IN A R To enlarge the picture (zoom in), press the ZOOM button, then use the right-arrow ( button. Vertical and Horizontal ➤ Lens Shift ) Vertical Lens Shift: To shift the projected image vertically, press the LENS button, then use the up and/or down-arrow ( , ) buttons. Horizontal Lens Shift (CL-810 Ultra Only): To shift the projected image horizontally, press the LENS button, then use the right and/or left-arrow buttons. 4.5 Selecting Video Memory • Press the MEM1 button on the remote control to recall settings for the current input from the “Memory 1” memory preset. MEM1 ISF NIGHT ISF DAY FACT PR • Press ISF NIGHT to recall settings for the current input from the “ISF Night” memory preset. • Press ISF DAY to recall settings for the current input from the “ISF Day” memory preset. • Press FACT to recall the factory-default settings for the current input. 4.6 Selecting an Aspect Ratio Use these buttons to select the appropriate aspect ratio for the type of program material being viewed. For more information on aspect ratios, refer to Table 4-1. 4.7 Adjusting the Picture • Press the BRT button on the remote control to adjust the image brightness. ANA 16X9 4X3 LBOX VWIDE CINEMA 1 2 VCINE BRT CONT COL TNT • Press CONT to adjust the image contrast. • Press COL to adjust the image color level. • Press TNT to adjust the hue of the image. For more information about these controls, refer to Picture Adjustment on page 33. 30 Runco CL-810 Series Owner’s Operating Manual Operation When you turn on the CL-810, it switches to the last selected input and looks for a valid signal. Use these buttons on the remote control to select an input source directly. VID ON OFF S-VID COMP1 RGBHD HDMI COMP2 Y PIP and PBP are not available when the CL-810 is used with the SDC-1 System Expansion Device. EL IM IN A R Note LIGHT For PIP and PBP purposes, there are two groups of inputs separated by their display modes: • Video (SD) group: Video, S-Video and Component 1 inputs. PBP ACT PIP PIP+ FOCUS FOCUS ZOOM ZOOM LENS LENS PIP- 4.8 Selecting An Input Source 4.9 Using Picture-In-Picture/ Picture-By-Picture (PIP/PBP) • Graphic (HD) group: HDMI and Component 2/RGB inputs. PIP / PBP shows one input from the Graphic group within or beside one input from the Video group. • Press PBP to enable the PBP function. Press PBP again to switch the screens left to right. Press PBP again to turn PBP off. • Press ACT (Active) to switch to the active window. (You can only switch inputs in the active window.) PR • Press PIP to enable the PIP function. Press PIP again to switch the main window. Press PIP again to turn PIP off. • To adjust the size of the PIP window, press PIP+ or PIP-. • Adjust the position of the PIP window with the arrow buttons ( , , , ). • Press the MENU button on the remote control to display the Main Menu. To select a menu item, use the UP and DOWN buttons on the remote control to highlight it. Press ENTER or to confirm your selection. • Use the arrow buttons to select menu items or change settings. • Press EXIT to return to the previous menu. • Press MENU to turn off the OSD menu. (When the Main Menu is displayed, pressing EXIT also turns off the menu.) The CL-810 OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on the selected input source and signal characteristics, some menu options may not be available. Runco CL-810 Series Owner’s Operating Manual 31 4.10 Using the On-Screen Menus Operation ICC Selection Store Image Settings Restore Image Settings Anamorphic (16:9) Standard (4:3) Letterbox Virtual Wide Cinema Virtual Cinema Language Picture Orientation Installation Keystone Adjust Background Color RS-232 Baud Rate Blue Image Reset Image Settings Sleep Timer Lamp Hours OSD Timer OSD Position PC & HD Adjust (480p and higher-res. signals only) Option PIP/PBP Set Up (not available when used with the SDC-1) Yes / No 0, 10, 20, 30 ... 180 minutes (read only) 0, 3, 6, 9 ... 60 seconds Horizontal Vertical Auto Frequency Phase H. Position V. Position PIP/PBP Enable PIP Set Up Y Aspect Ratio Color Temperature 0 ... 60 0 ... 32 0 ... 64 0 ... 30 -14 ... 0 ... +20 0, 1, 2 or 3 0, 1 (5400 K), 2 (6500K), 3 (8500 K), 4 or 5 (Custom) Standard, NTSC, HDTV or PAL Memory 1 Memory 1, ISF Night or ISF Day PBP Set Up (available only on CL-810 projectors equipped with the CineWide option) English, French, Spanish, German or Italian Floor Front, Floor Rear, Ceiling Front or Ceiling Rear -14, -13 ... 0 ... +13, +14 Blue or White 9600, 38400 or 115200 On / Off EL IM IN A R Video S-Video Component1 Component2 RGB-HD HDMI Brightness Contrast Color Tint Sharpness Filter DNR White Balance Gamma Selection SD Enhance RVR Adjust Set Up Image Over Scan PR Image Shift Amplitude Adjust Horizontal Masking Video Black Level Lamp Power Remote Control Reset Lamp Timer Mode Fan Control Screen Trigger Mode Return to User OSD Reset Picture Adjust Fan Speed (Manual Mode) Normal or AutoScope Blue Image Yes / No Brightness, Contrast, Color etc. Gamma, Gain, Offset etc. 2.8, 2.5, 2.2, 1.0, RUNCO Enhance 1, RUNCO Enhance 2 or ISF Day On / Off ICC Adjust NTSC / HDTV / PAL Picture Adjust White Balance Gamma Selection ISF Calibration 0, +1, +2, +3 ... +15 Gamma Gain Offset Store Color Temp. 4 Store Color Temp. 5 2.8, 2.5, 2.2, 1.0, RUNCO Enhance 1, RUNCO Enhance 2 or ISF Day H Enhance V Enhance Chroma Enhance H Threshold V Threshold Chroma Threshold 0, 1, 2 ... 19 Total Horizontal Vertical Horizontal Vertical Horizontal Vertical 0, +1, +2, +3 ... +100 0 IRE or 7.5 IRE 250W or 200W Primary Secondary Yes / No Store Settings Splash Screen Timer ISF Enable Return to User OSD 0, +1, +2, +3 ... +17 0, +1, +2, +3 ... +31 -30, -29 ... 0 ... +29, +30 -28, -27 ... 0 ... +29, +30 On / Off PIP Off Graphic in Video Video in Graphic PBP Off Graphic by Video Video by Graphic Red / Green / Blue 0, +1, +2, +3 ... +127 0, +1, +2, +3 ... +15 -30, -29, ... 0 ... +29, +30 -60, -59 ... 0 ... +59, +60 (CineWide versions only) Auto Normal, Auto Hi. Altitude or Manual (CineWide versions only) (see above) (see above) R/G/B/Y/C/M Intensity / Sat. / Hue Memory 1, ISF Night or ISF Day +5, +6, +7 ... +60 seconds On / Off Figure 4-1. CL-810 OSD Menu Structure 32 Runco CL-810 Series Owner’s Operating Manual Operation The Main Menu is the starting point for accessing all projector functions. Main Menu (The Set Up and ISF Calibration menus are hidden and not accessible until you enter a passcode.) The active source is indicated by an arrow (>) to its left; in the example at left, Video is the active source. To select a different source, use the or button to highlight it and press ENTER or . Runco CL-810 > Video S-Video Component1 Component2 RGB-HD HDMI ----------------- EL IM IN A R Y Aspect Ratio Use the controls in the Adjustment Menu to calibrate your CL-810 for optimum picture quality. To access the Adjustment menu, press MENU, highlight the active source and press ENTER or . To adjust a setting, use the or button to highlight it and press ENTER. Use the or button to change the setting. When finished, press EXIT. PR The CL-810 has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal video performance and has implemented a training program for technicians and installers to use these standards to obtain optimal picture quality from Runco video display devices. Accordingly, Runco recommends that setup and calibration be performed by an ISF certified installation technician. All signal types require separate processing. Therefore, you need to calibrate each input separately. Runco recommends calibrating the CL-810 inputs in the following order: 1. Component 1 2. RGB-HD / Component 2 3. S-Video 4. Composite 5. HDMI Note When you change a picture quality setting, save the change to a preset afterwards. Otherwise, the change will be lost when a different input is selected. (Picture quality settings are saved for each input and resolution separately.) For information about saving settings, refer to Store Image Settings on page 38. Runco CL-810 Series Owner’s Operating Manual 33 Installation Option Set Up ISF Calibration Picture Adjustment Adjustment Brightness Contrast Color Tint Sharpness Filter Color Temperature ICC Selection Store Image Settings Restore Image Settings Operation Although it may be possible to obtain satisfactory picture quality using the naked eye and regular program material, Runco recommends using the following calibration tools for best results: • External test pattern source -- Sencore VP401 Multimedia Video Generator, Ovation Multimedia test DVD or equivalent. • A blue filter (provided with many test DVDs), for color level and tint adjustments. Connect your test pattern source to the input that you are calibrating and proceed as follows. Perform the adjustments in the order listed here. EL IM IN A R Y Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-2 shows a typical PLUGE pattern. Below Black Above Black PR Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes. Select Brightness from the Adjustment menu and press ENTER. Adjust the brightness so that: • The darkest black bars disappear into the background. • The dark gray areas are barely visible. • The lighter gray areas are clearly visible. • The white areas are a comfortable level of true white. • The image contains only black, gray and white (no color). 34 Runco CL-810 Series Owner’s Operating Manual Operation EL IM IN A R Y Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in Figure 4-3. Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast Select Contrast from the Adjustment menu and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size. Brightness and contrast controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting. Note blue red magenta green cyan PR yellow gray Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4. Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint Runco CL-810 Series Owner’s Operating Manual 35 Operation blue EL IM IN A R Y red magenta green cyan yellow gray Select Color from the Adjustment menu and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue: Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint from the Adjustment menu and press ENTER. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue. PR Note Like the brightness and contrast controls, the color and tint controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting. 36 Runco CL-810 Series Owner’s Operating Manual Operation EL IM IN A R Y Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Adjustment menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. Note PR Figure 4-5. Typical Test Pattern for Adjusting Sharpness The Sharpness setting has no effect if the Sharpness Filter (see below) is set to 0. Filter: The Filter setting controls the behavior of the Sharpness control. The available settings depend on the vertical resolution of the input signal, as follows: • With a 480i signal, you can apply the sharpness control to either the input signal (1), the output signal (2), both (3) or neither (0). • With a 480p or higher-resolution signal, the sharpness control is applied only to the output signal and only when you set the Sharpness Filter to “on” (1). Runco CL-810 Series Owner’s Operating Manual 37 Operation Color Temperature: The CL-810 has six memory settings for Color Temperature. Four of these settings are factory set to default as follows: Color Temperature 2 - • 0 -- Original lamp color temperature + • 1 -- 5400 kelvins • 2 -- 6500 kelvins • 3 -- 8500 kelvins • 4 -- Custom • 5 -- Custom EL IM IN A R Y Custom 4 and 5 memory are installer-adjustable and can be used to create custom settings. There are nine adjustable “white balance” parameters available for the Custom 4 and 5 settings (three each for red, green and blue). These are described later in this section; refer to Set Up on page 42. Note You must enter a passcode in order to enter the Set Up menu. ICC Selection: Use the ICC Selection menu to select the color space that is appropriate for the source signal, to achieve optimal color balance. PR Note Aspect Ratio ➤ Aspect Ratio The International Color Consortium (ICC) is a group of imaging product vendors that promotes and develops cross-platform, vendor-neutral color measurement and management standards. If you select NTSC, HDTV or PAL, you can make further adjustments to individual color space characteristics in the ICC Adjust sub-menu under the ISF Calibration menu, described later in this section. (The Standard color space is factory-set and not adjustable.) Store Image Settings: Once the desired adjustments have been entered, select Store Image Settings to save these settings into the “Memory 1” memory location. Restore Image Settings: To recall stored custom image quality settings, select Restore Image Settings and choose “Memory 1,” “ISF Night” or “ISF Day.” To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio from the Main Menu and press ENTER. Select the appropriate aspect ratio for your screen size and the type of program material being viewed; refer to Table 4-1. Anamorphic (16:9) Standard (4:3) Letterbox Virtual Wide Cinema Note When you change the aspect ratio, save the change to a preset afterwards. Otherwise, the change will be lost when a different input is selected. (The aspect ratio is saved for each input and resolution separately.) Virtual Cinema 38 Runco CL-810 Series Owner’s Operating Manual Operation Table 4-1. Aspect Ratio Settings Aspect Ratio Remote Control Key Anamorphic ANA Description EL IM IN A R Y 16:9 Image on 16:9 Screen Select Anamorphic to view 16:9 DVDs and HDTV programs in their native aspect ratio. 4:3 images are stretched horizontally to fit a 16:9 screen. 4:3 Image on 16:9 Screen Standard 4:3 4X3 Active Image Area (4:3) LBOX PR Letterbox Letterbox Image on 16:9 Screen Standard 4:3 scales the input signal to fit in the center of the 16:9 screen. 4:3 is the aspect ratio used by computer monitors, standard television programming and most VHS video cassettes. In Letterbox mode, the image is stretched vertically; the top and bottom portions are “blanked off.” Letterbox is best suited for viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen. VirtualWide VWIDE A 4:3 image is scaled NON-linearly (more on the sides than in the center) to fit a 16x9 screen. Cinema CINEMA Select Cinema to view 2.35 source material on a 16:9 screen. The upper and lower portions of the screen are masked, but the geometry of the active image area is not changed. 2.35:1 Image on 16:9 Screen Runco CL-810 Series Owner’s Operating Manual 39 Operation Table 4-1. Aspect Ratio Settings (continued) Aspect Ratio Remote Control Key Virtual Cinema VCINE Description Y 2.35:1 Image on 16:9 Screen EL IM IN A R 2.35:1 Image on 16:9 Screen with Virtual Cinema A 2.35 image is stretched anamorphically in both directions to fill a 16:9 image. (The secondary anamorphic lens then “stretches” the image back to 2.35:1.) Virtual Cinema is available only on CL-810 projectors equipped with the CineWide option. 2.35:1 Image on 2.35:1 Screen with Virtual Cinema Installation ➤ Installation Language PR Picture Orientation Keystone Adjust To access the Installation adjustments, press MENU, then press the or button to highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears. Press EXIT to return to the previous menu or press MENU to close all menus. Note Background Color RS-232 Baud Rate Blue Image When you change a setting in the Installation menu, the change takes effect immediately; you do not need to press ENTER afterwards. (Press EXIT to return to the previous menu or MENU to exit.) Language: Press the or button to select from the available languages: English, French, Spanish, German and Italian. Picture Orientation: Press the or button to change the orientation of the projected image. The CL-810 can be installed on a ceiling or in a rear-screen configuration with one or more mirrors. There are four settings: Floor Front, Ceiling Front, Floor Rear and Ceiling Rear. Keystone Adjust: To correct distortion resulting from the angle of projection, select Keystone Adjust and use the or button to make the image rectangular. Tip Runco recommends that the keystone feature not be used unless absolutely necessary, as it may cause artifacts in the image. Background Color: Press the or button to select the image Background Color (blue or white). The Background Color appears when no incoming signal is present. 40 Runco CL-810 Series Owner’s Operating Manual Operation RS-232 Baud Rate: Press the or button to select the projector’s RS-232 Baud Rate. This function is used to change the transfer rate of the RS-232 connection. (This setting must match the data rate of the device connected to the RS-232 input.) Blue Image: Press the or button to turn the Blue Image Off or On. This feature removes all red and green color information from the image (simulating a blue filter), and is useful for color-calibrating the projector or other video components. To access the Option adjustments, press MENU, then press the or button to highlight Option and press ENTER. The Installation sub-menu will then appear (see above). Press EXIT to return to the previous menu or press MENU to close all menus. Y Reset Image Settings: To restore the default image settings for the current input source ONLY, press the button to highlight “Yes,” then press ENTER. EL IM IN A R Sleep Timer: The Sleep Timer automatically puts the projector into standby mode after the amount of time you specify here. (A warning appears on-screen one minute before this is to occur.) Use the or button to set the timer for anywhere from 10 minutes to 3 hours, in 10-minute increments. To disable the Sleep Timer, set it to 0. Lamp Hours: To find out how long the projector lamp has been in use, select Lamp Hours and press ENTER. OSD Timer: Use the or button to set the OSD Timer. This timer controls how long the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in 3-second increments. When you set the OSD to 0, the menus remain on-screen until you hide them by pressing MENU. PR To adjust the horizontal and vertical position of the OSD, select OSD Position and press ENTER. Then, press the or button to select Horizontal or Vertical and use the or button to adjust. PC & HD Adjust: Use the settings in the PC & HD Adjust menu to fine-tune 480p and higher-resolution signals for optimum picture quality. • Auto: Adjusts the phase, frequency and position automatically. • Freq. Adjusts the frequency of the signal. • Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or “noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR. For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may find that you can stabilize the image at more than one point. Use either setting in this case.) • H. Pos.: Adjusts the horizontal position of the image. • V. Pos.: Adjusts the vertical position of the image. Note To adjust the image position with a 480i source, use the Image Shift controls in the Set Up menu (see page 43). Runco CL-810 Series Owner’s Operating Manual 41 Option Option Reset Image Settings Sleep Timer Lamp Hours OSD Timer OSD Position PC & HD Adjust DNR Operation PIP/PBP Set Up: Select PIP/PBP Set Up from the Option menu to change the PIP/PBP settings. • PIP/PBP Enable: Press the or button to select PIP/PBP Enable, then press ENTER. Press the or button to select Off or On, then press ENTER. • PIP Set Up: Press the or button to select PIP Set Up, then press ENTER. Press the or button to select PIP Off, Graphic in Video or Video in Graphic, then press ENTER. • PBP Set Up: Press the or button arrows to select PBP Set Up, then press ENTER. Press the or button to select PBP Off, Graphic by Video or Video by Graphic, then press ENTER. Set Up EL IM IN A R Y DNR: Use the or button to adjust the Digital Noise Reduction (DNR). DNR is useful for clearing up noisy images from interlaced SD sources. Adjust as desired, keeping in mind that reducing noise (which reduces high frequencies) may also soften the image. To access advanced picture quality adjustments, use the up- or down-arrow keys to highlight Set Up and press ENTER. Use the number buttons on the remote to enter the Set Up menu passcode when prompted and press ENTER again. Then, press MENU on the remote control. PR White Balance: To remove any trace of color from the white areas of the projected image, choose White Balance from the Set Up menu and press ENTER. • Gamma: “Gamma” is a global setting that determines how gray shades are displayed between minimum input (black) and maximum input (white) for all signals. A good gamma setting helps to optimize blacks and whites while ensuring smooth transitions for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast” controls, the overall tone of your images can be lightened or darkened without changing the extremes and all images will be more vibrant while still showing good detail in dark areas. In all but the most unusual situations, the appropriate “Gamma Selection” (see below) will produce accurate colors and a satisfying contrast level. However, it is sometimes necessary to adjust the red, blue and green gamma curves individually. To do this, select Gamma from the White Balance sub-menu and use the left- and right-arrow buttons to manipulate the on-screen slidebars. • Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, decrease the Gain for that color. • Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease the Offset for that color. • Store Color Temp.4/Store Color Temp.5: When you are finished adjusting the o Ga Gaooain 42 Runco CL-810 Series Owner’s Operating Manual Operation Gamma Selection: The normal gamma setting of 2.2 is correct for almost all signals and conditions. If excess ambient light washes out the image and it becomes difficult or impossible to see details in dark areas, lower the gamma setting to compensate. This will improve contrast while maintaining good details for blacks. Conversely, if the image is washed out and unnatural, with excessive detail in black areas, increase the setting. Again, good gamma improves contrast while maintaining good details for blacks and whites. SD Enhance: The SD Enhance menu gives you options for improving the quality of standard-definition, 480i images. (For 480p and higher-definition images, the controls in this menu are disabled.) Keep in mind that these controls add frequencies that are not present in the original signal, and may make images appear “noisy” if misused. Y • H Enhance/V Enhance: These controls can improve the apparent horizontal and/or vertical resolution of the image. EL IM IN A R • Chroma Enhance: This control adds chroma (color information) to the input signal and can make colors appear more vibrant and saturated. • H Threshold/V Threshold/Chroma Threshold: Set these to +11 or higher to activate the enhancement controls described above. Generally, the higher the threshold, the more noticeable the enhancements you make will be. RVR Adjust: Use the RVR Adjust control to increase or decrease the Reflectance Volume Regulation setting. RVR lets you control the aperture or iris size (the physical opening through the lens; similar to an “f-stop” on a camera). Doing so allows you to optimize brightness and contrast according to the amount of ambient light in the viewing area. Use a higher setting for rooms with lots of ambient light. Use a lower setting for more “theater-like” viewing conditions (little or no ambient light). Image Over Scan: Image Over Scan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area. PR Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Over scan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area. Use the on-screen slidebar to select the desired amount of over scan. For HDTV, DVDs and other video sources, Image Over Scan is generally not necessary or desirable. Image Shift: The Image Shift menu allows you to precisely center the image on the screen. (These controls are available only with a 480i source signal.) • Horizontal: This control moves the image right or left within the area of available pixels. • Vertical: This option moves the image up or down within the area of available pixels. Note 1. To adjust the image position with a 480p or higher-resolution source, use the PC & HD Adjust controls in the Option menu, described on page 41. 2. The values shown represent where the approximate center of the image lies in relation to the total number of pixels available horizontally or vertically. This varies widely according to the signal; watch the image while adjusting. Runco CL-810 Series Owner’s Operating Manual 43 Operation Amplitude Adjust: The Amplitude Adjust menu allows you to fine-tune the curently-selected image aspect ratio by stretching it horizontally or vertically, in small increments. This can be useful if your projector is equipped with an anamorphic lens. The Horizontal control adjusts the image width while keeping the height constant. Similarly, the Vertical control adjusts the image height while keeping the width constant. Horizontal Masking (CineWide CL-810 versions only): To achieve the proper image geometry with the secondary anamorphic lens, select Horizontal Masking from the Set Up menu. Then, use the or button to change the native aspect ratio of the display, in small increments. EL IM IN A R Y Video Black Level: This control compensates for incoming elevated black levels present in certain video signals, and ensures that blacks in the display are neither “crushed” (where dark grays appear black) nor excessively elevated (where blacks appear dark gray). By default, the projector automatically determines the best setting according to the type of incoming video signal: • 0 IRE: Used for DVD output with “enhanced black,” SECAM, most PAL standards and Japanese NTSC. • 7.5 IRE: Used for most NTSC video signals. For some types of video, you may want to override the setting. Generally, if black appears crushed when brightness = 30, choose “0 IRE.” If black appears excessively elevated, use “7.5 IRE.” PR Lamp Power: Select Lamp Power from the Set Up Menu to adjust the lamp output level. You can choose to run the lamp as bright as possible (250W; this is the default setting) or you can choose the lower (200W) setting. Generally, lower lamp output can prolong the life of the lamp, but decreases brightness. Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the CL-810 will respond. The Primary IR code is permanently set to +20. The secondary IR code is also +20. You can change the secondary IR code if either: • Another device in the theater (a DVD player, for example) is responding to commands from the CL-810 remote control in ways that are unpredictable or undesirable. • You have multiple CL-810 projectors and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific projector. When you change the secondary IR code, the remote sends that code instead of the primary IR code. Note The Remote Control menu is read-only and need not be visible in order to change the secondary IR code. To simultaneously change the secondary IR code and synchronize that remote with a projector, point the remote at the projector, then press and hold and simultaneously for five seconds. The Remote Control edit window, shown at right, appears. Type a new, two-digit code. 44 Runco CL-810 Series Owner’s Operating Manual Operation The procedure for changing the secondary IR code on the remote only is the same, except that you point the remote away from the projector. Reset Lamp Timer: When you replace the projector lamp (refer to Lamp Replacement on page 49), you should also reset the lamp timer. To do this, select Reset Lamp Timer from the Set Up menu. Press the right-arrow key on the remote to highlight “Yes,” then press ENTER to confirm the reset. Reset the Lamp Timer ONLY after you replace the lamp. Otherwise, the reported “Lamp Hours” will be inaccurate. WARNING Do not exceed the recommended lamp life of 2000 hours. An old lamp becomes increasingly fragile and prone to sudden failure. EL IM IN A R Y Note Fan Control: Select Fan Control from the Set Up Menu to control the operation of the projector’s cooling fan. • Mode: In most cases, the default Fan Control Mode (Auto Normal) will maintain the correct operating temperature. If the lamp frequently turns off due to overheating, or in certain high-altitude operating environments, you may need to change this setting to Auto Hi. Altitude or Manual. • Fan Speed: If you set the Fan Mode to Manual, select Fan Speed and use the on-screen slidebar to adjust the speed. After changing either of these settings, press EXIT to return to the previous menu. Screen Trigger Mode: Select Screen Trigger Mode from the Set Up menu to configure the 12-volt trigger output. PR • Set the Screen Trigger Mode to Normal if you want the trigger to activate when the projector is turned on (for instance, if the trigger is controlling a retractable screen). • Set the Screen Trigger Mode to AutoScope if you want the trigger to activate when the Cinema or Virtual Cinema aspect ratio is selected. Choose this setting if your CL-810 is equipped with the Runco CineWide with AutoScope system. Note If your CL-810 installation includes an SDC-1 System Expansion Device, you can also use the SDC-1 to trigger the AutoScope lens motor. Refer to the SDC-1 manual for more information. Return to User OSD: To exit the Set Up menu, use the up- or down-arrow keys to highlight Return to User OSD and press ENTER. To return to the Set Up menu, select it from the Main Menu, press ENTER twice, then press MENU on the remote control. (You do not need to re-enter the passcode.) Runco CL-810 Series Owner’s Operating Manual 45 Operation ISF Calibration ➤ ISF Calibration Reset Picture Adjust To access the ISF Calibration menu, select ISF Calibration from the Main Menu and press ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu passcode when prompted and press ENTER again. Then, press MENU on the remote control. Picture Adjust White Balance Note Gamma Selection This menu should be used by ISF-certified technicians only. Blue Image ICC Adjust Reset Picture Adjust: To restore the ISF default image settings for the current input source ONLY, press the button to highlight “Yes” then press ENTER. Store Settings Splash Screen Timer Y Picture Adjust: These settings are described in the Picture Adjustment section (page 33). ISF Enable EL IM IN A R Return to User OSD White Balance / Gamma Selection: These settings are described in the previous section, Set Up. Blue Image: This setting is described in the Installation section (refer to page 41). ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL color space characteristics. To do this, select the color space to modify. Then, select a component color (Red, Green, Blue, Yellow, Cyan or Magenta). For each component color, you can adjust the following: • Intensity: This slidebar adjusts the intensity -- also known as luminance -- of a given color. PR • Sat. This slidebar adjusts the color saturation level -- the amount of that color in a video image. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic. • Hue: This slidebar adjusts the red/green color hue for true color reproduction of video signals. For best results, adjust tint while displaying an external color bars test pattern (see Figure 4-4). Otherwise, it is recommended that Hue remain at its default setting. When you have finished customizing the color space, select Store Setting and press ENTER. Store Settings: For each input, the CL-810 lets you store image quality settings as presets that you can recall at a later time. You can create up to three presets per input and resolution. Note When you change a setting, save the change to a preset afterwards. Otherwise, the change will be lost when a different input is selected. (Most settings are saved for each input and resolution separately.) When you have finished calibration, select Store Settings and choose "Memory 1,” “ISF Night” or “ISF Day” to store your settings. To recall stored custom image quality settings, select Restore Image Settings from the Adjustment menu (refer to Picture Adjustment on page 33) and choose “Memory 1,” “ISF Night” or “ISF Day.” Or, simply use the corresponding buttons on the remote control. 46 Runco CL-810 Series Owner’s Operating Manual Operation Splash Screen Timer: Use the or button to set the Splash Screen Timer. This timer controls how long the startup (ISF and Runco logo) image stays on-screen after you turn on the projector. Select from 5 to 60 seconds, in 1-second increments. When finished, press EXIT. ISF Enable: Use ISF Enable to control the display of the ISF logo on the CL-810 splash screen upon power-up. Return to User OSD: To exit the ISF Calibration menu, use the up- or down-arrow keys to highlight Return to User OSD and press ENTER. PR EL IM IN A R Y To return to the ISF Calibration menu, select it from the Main Menu, press ENTER twice, then press MENU on the remote control. (You do not need to re-enter the passcode.) Runco CL-810 Series Owner’s Operating Manual 47 Operation PR EL IM IN A R Y Notes: 48 Runco CL-810 Series Owner’s Operating Manual Maintenance and Troubleshooting 5 The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to obtain a replacement lamp. EL IM IN A R Y 1. Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. 2. Loosen the two captive screws from the lamp cover. 3. Remove the lamp cover. PR 4. Remove the two lamp assembly mounting screws. 5. Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing. 6. Install the new lamp module and replace the two screws. 7. Replace the lamp cover at the right side first and secure it with the two screws. 8. Turn on the power and select Reset Lamp Timer from the Set Up menu to reset the lamp timer (refer to Reset Lamp Timer on page 45). Runco CL-810 Series Owner’s Operating Manual 49 5.1 Lamp Replacement Maintenance and Troubleshooting 5.2 Troubleshooting Tips Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the CL-810. If the suggested solutions fail to resolve the problem or if you encounter an issue not described here, please contact Runco Technical Support. Table 5-1. Troubleshooting Chart Symptom Possible Cause(s) Solution • The CL-810 is not plugged in or the AC outlet is not active. • The main power switch (at the rear of the projector) is off. • Lamp cover is not securely attached. • Ensure that the CL-810 is plugged in and that the AC outlet is active. • Turn on the power switch. The projector does not turn back on after it was powered off. • The projector will not turn on for two minutes after power-off, to protect the lamp. • Wait until the CL-810 completes its cool-down (POWER LED lights solid orange). The remote control does not work correctly. • The batteries have run out. • Replace the batteries. The projector is on and OSD menus appear, but there is no video image on-screen. • Incorrect source selection. • Source component is not turned on. • Source component is connected incorrectly or not at all. • Select the correct source. • Turn on the source. A projected image from a DVD is split or otherwise scrambled. • DVD player is connected to the Component input and set to progressive scan mode. • Turn off progressive scan on the DVD player. Image is blurred. • The lens is not correctly focused. • Adjust the focus with the remote control. Image is too bright and/or lacks definition in the bright areas of the image. • Contrast is set too high. • Lower the contrast setting. Image appears “washed out” and/or dark areas appear too bright. • Brightness is set too high. • Lower the brightness setting. Colors in the image are swapped; for example, reds appear blue or vice versa. • The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the CL-810. • Ensure that the source outputs are connected to the correct CL-810 input. PR EL IM IN A R Y The projector does not turn on. 50 • Securely attach the lamp cover. • Check cable connection from source component to projector. Runco CL-810 Series Owner’s Operating Manual Maintenance and Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Solution • The lamp cover is open. • Fans are not working properly. • Close the lamp cover. • Please contact your Runco dealer for assistance. LAMP LED lights solid red. • The lamp has failed or exceeded its usage life. • Replace the lamp with a new one. TEMP LED lights solid red. • CL-810 internal temperature is too high. • Power off the CL-810 and allow it to cool down. Ensure that the intake and exhaust vents are not blocked. Turn the projector back on. If the problem persists, please contact your Runco dealer for assistance. PR EL IM IN A R Y TEMP and LAMP LEDs are both flashing red. Runco CL-810 Series Owner’s Operating Manual 51 Maintenance and Troubleshooting PR EL IM IN A R Y Notes: 52 Runco CL-810 Series Owner’s Operating Manual 6 Serial Communications To interface the CL-810 with a home theater automation/control system or a PC running terminal emulation software: 1. Connect it to your control system or PC as shown in Figure 3-11. 6.1 RS-232 Connection and Port Configuration 2. Start a terminal session on your PC using a terminal-emulation program, such as HyperTerminal. EL IM IN A R Y 3. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to match that of the projector (115200, 38400 or 9600). 4. Press . You should see a command prompt (>) in the terminal window. 5. Type a command from among those listed in Table 6-1 and press . For example, to change the aspect ratio to Letterbox, type x063x . Serial commands to the CL-810 take the following form: • Commands are in ASCII format. • Commands are not case-sensitive; X001X and x001x are equivalent. • A carriage return MUST follow each command. The CL-810 will not accept serial commands for 20 seconds after it is turned on or off. PR Note Table 6-1. Serial Commands Code x001x Function Power On x002x Power Off x003x Menu x004x Enter x005x Exit x006x Up (arrow key) x007x Down (arrow key) x008x Left (arrow key) x009x Right (arrow key) x011x Show active source and aspect ratio information x021x Keypad 1 x022x Keypad 2 Runco CL-810 Series Owner’s Operating Manual 53 6.2 Serial Command Syntax Serial Communications Table 6-1. Serial Commands (continued) Code Function Keypad 3 x024x Keypad 4 x025x Keypad 5 x026x Keypad 6 x027x Keypad 7 x028x Keypad 8 x029x Keypad 9 x030x Keypad 0 x031x Store image settings to Memory 1 x032x Store image settings to ISF Night x033x Store image settings to ISF Day x046x Restore image settings from Memory 1 x047x Restore image settings from ISF Night x048x Restore image settings from ISF Day x049x Load default of current source x051x Single source, full-screen x052x PIP - graphics on video x053x PIP - video on graphics x054x PBP - graphics by video x055x PBP - video by graphics x056x PIP - increase sub-window size x057x PIP - decrease sub-window size x058x Set PIP/PBP active window x061x Anamorphic (16:9) aspect ratio x062x Standard (4:3) aspect ratio x063x Letterbox aspect ratio x064x VirtualWide aspect ratio x065x Cinema aspect ratio x066x Virtual Cinema aspect ratio x071x RS-232 baud rate = 9600 x072x RS-232 baud rate = 38400 x073x RS-232 baud rate = 115200 PR EL IM IN A R Y x023x 54 Runco CL-810 Series Owner’s Operating Manual Serial Communications Table 6-1. Serial Commands (continued) Function Image orientation = floor front x082x Image orientation = ceiling front x083x Image orientation = floor rear x084x Image orientation = ceiling rear x091x Lamp Power = 200W x092x Lamp Power = 250W x121x OSD Language = English x122x OSD Language = French x123x OSD Language = Spanish x124x OSD Language = German x125x OSD Language = Italian x131x Switch to Composite input x132x Switch to S-Video input x133x Switch to RGB-HD input x134x Switch to DVI input (HDMI) x135x Switch to Component 1 input x136x Switch to Component 2 input x156x Background Color = Blue x181x x281x PR x157x EL IM IN A R x081x Y Code Background Color = White Toggle Blue Image on/off Vertical Lens Shift = Up x282x Vertical Lens Shift = Down x283x Zoom In x284x Zoom Out x285x Focus (rotate lens to right) x286x Focus (rotate lens to left) x287x RVR = Full On (open) x288x RVR = Full Off (closed) Runco CL-810 Series Owner’s Operating Manual 55 Serial Communications PR EL IM IN A R Y Notes: 56 Runco CL-810 Series Owner’s Operating Manual Specifications 7 7.1 CL-810 Specifications Table 7-1 lists the CL-810 specifications. Table 7-1. CL-810 Specifications Digital Light Processing (DLP), Single-Chip SuperOnyx DMD Native Resolution: 1280 x 720 (16:9) Aspect Ratios: 4:3, Letterbox, 16:9 Anamorphic, VirtualWide, Cinema, Virtual Cinema Video Standards: EL IM IN A R Y Projector Type: NTSC, PAL, SECAM DTV Compatibility: Scan Frequency: 480p, 576p, 720p, 1080i Horizontal: 15 - 80 kHz Vertical: 50 - 100 Hz Picture Size (16:9 Screen): Throw Distance (Factor x Screen Width): CL-810: 1.80 to 2.43 CL-810 Ultra: Refer to Table 3-3 Refer to Table 3-4 PR Horizontal and Vertical Offset: Recommended Width: 72 in. (1.83 m) to 96 in. (2.44 m) Capable of screen widths between 48 in. (1.22 m) and 200 in. (5.08 m) Runco CL-810 Series Owner’s Operating Manual 57 Specifications Table 7-1. CL-810 Specifications (continued) Cinema Standards Measurement System (CSMS) Specifications Brightness*: 14.5 to 21.6 foot-Lamberts (fL) Contrast Ratio*: 200:1 to 220:1 *Variable depending on RVR setting These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter, Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6,500K and has a minimum of 150 hours of usage. The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen surface. The Society of Motion Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light output. IM IN A R Y Brightness and Contrast: These specifications are obtained by calibrating the projector as described above for CSMS measurements. Industry-Standard Specifications Light Output: 1250 ANSI Lumens Contrast Ratio: 1500:1 to 3100:1 EL PR Home Theater Calibration Specifications Light Output: 442 to 587 ANSI Lumens Contrast Ratio*: 200:1 to 220:1 These are typical projector brightness and contrast specifications found in most companies’ sales literature. Runco includes these measurements in its literature to allow for direct comparison with other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance data when the projector is used in professional, commercial and industrial displays. Lamp: 250 Watts Estimated Lamp Life: 2000 hours Video Inputs: (1) Composite Video, (1) S-Video, (1) RGB/Component Video (BNC connectors), (1) RCA Component Video, (1) HDMI Control Options: - RS-232 Communication Parameters: 9600, 38400 or 115200 bps, no parity, 8 data bits, 1 stop bit, no flow control 12V Output: Max. 0.25 Amps, active when Cinema or Virtual Cinema Aspect Ratio is selected (CineWide versions only) or when projector is turned on Power Requirements: 100 to 240 VAC (auto-sensing), 50/60 Hz, 310 Watts Operating Environment: 41°F to 95°F (5°C to 35°C), 20% to 80% humidity (non-condensing) Dimensions: CL-810: See Figure 7-1 CL-810 Ultra: See Figure 7-2 58 Discrete IR remote Serial commands via RS-232 Runco CL-810 Series Owner’s Operating Manual Specifications Table 7-1. CL-810 Specifications (continued) Weight (without lens): CL-810: 34 lbs. (15.42 kg) CL-810 Ultra: 36 lbs. (16.33 kg) Regulatory Approvals: Complies with FCC, CE C-Tick Limited Warranty: Projector: Two (2) years parts and labor from the date of delivery to the end user. Lamp: 1000 hours or six (6) months, whichever comes first. PR EL IM IN A R Y Specifications are subject to change without notice. Runco CL-810 Series Owner’s Operating Manual 59 Specifications Figure 7-1 shows the CL-810 dimensions. PR EL IM IN A R Y 7.2 CL-810 Dimensions Figure 7-1. CL-810 Dimensions 60 Runco CL-810 Series Owner’s Operating Manual Specifications 7.3 CL-810 Ultra Dimensions PR EL IM IN A R Y Figure 7-2 shows the CL-810 Ultra dimensions. Figure 7-2. CL-810 Ultra Dimensions Runco CL-810 Series Owner’s Operating Manual 61 Specifications PR EL IM IN A R Y Notes: 62 Runco CL-810 Series Owner’s Operating Manual SERIAL NUM BER RUMA-011135 rev 02-14-06 v2.0 Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300 www.runco.com Runco CL-810 Owner’s Operating Manual
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Warning : Invalid xref tableEXIF Metadata provided by EXIF.tools