SALUS North America SS901ZB Water Leak Sensor User Manual WLS QSG ENv1

Download:
Mirror Download [FCC.gov]
Document ID	3925154
Application ID	Bb3yb6qSahX9FdwS4sibAQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	113.92kB (1424034 bits)
Date Submitted	2018-07-16 00:00:00
Date Available	2018-07-16 00:00:00
Creation Date	2018-06-26 19:22:11
Producing Software	Mac OS X 10.13.5 Quartz PDFContext
Document Lastmod	2018-07-12 11:38:04
Document Title	WLS-QSG ENv1
Document Creator	Word
Document Author:	Sam Pai

Installation/Quick Start Guide: Water Leak Sensor (SS901ZB)
Visit www.salusinc.com for the User Manual
In the Box
Tools Needed
Note:
Additional equipment may be required due to
building construction or materials, or other radio
interference that may reduce the radio range.
Water Leak Sensor w/ Battery
(1x CR2, 3V Lithium)
Stand
Sensor Cable
PAIRING INSTRUCTIONS
• Follow your system’s instructions to prepare to add devices to the
system.
• Remove the Face Plate from the sensor by turning the Face Plate
counter-clockwise and pull the battery tab to start the pairing
process.
• When the sensor is detected and added to the system, replace the
Face Plate by aligning the dots and turning the Face Plate clockwise.
• Make sure the dots are fully aligned for a proper seal, then proceed
to the sensor installation.
Installation/
Quick-start Guide
Screws and Anchors
Adhesive Pad
INSTALLING THE SENSOR CABLE (OPTIONAL)
• To install the Sensor Cable, first run the cable to the desired location,
and fasten the winged end of the Sensor Cable into place. Note that
the tips are angled to improve the sensing ability when the tips are
near a surface.
Surface Install
Sump Install
#1 Phillips Screwdriver
TESTING THE SENSOR
• To test the sensor, remove it from the stand or floor
• Insert the sensor into the stand 90 degrees from upright in either
direction to short the contacts on the sensor.
• The sensor will send a message to the connected home system
indicating a water leak. The LED will not light up to preserve battery
life.
REPLACING THE BATTERY
(Use only Panasonic CR2 3V lithium battery)
INSTALLATION INSTRUCTIONS
• Identify a level surface for the sensor, where water will likely
accumulate in the event of a leak. If the sensor is too wide for
placement at the desired location, the stand can be used for a
narrower profile.
For tighter
locations or
locations with
radio problems,
use the
included
Sensor Cable.
• Insert the square end of the Sensor Cable into the terminals on the
stand.
• Screw down both terminals until the cable is firmly held in place
• Mount the Stand to the wall or other surface using the supplied
double-sided adhesive pad or screws.
• Insert the Water Leak Sensor into the stand to begin operation.
• Grasp the top of the sensor Face Plate, rotate counter-clockwise
and lift from the sensor Body.
• Grasp the battery from both ends and lift to remove the battery
from the sensor.
• Insert a new battery into the sensor, observing the proper polarity.
• Position the sensor Face Plate over the Sensor Body, aligning the
dots on the Face Plate and Body, then rotate clockwise to align the
dots again to close.
Version 1
FACTORY RESETTING THE SENSOR
Remove the sensor Face Plate.
Remove the battery.
Press and hold the Tamper Switch while re-inserting the battery.
Release the Tamper Switch when the LED lights on the front of the
sensor. The sensor is reset to factory defaults and will respond to
pairing requests.
• After pairing, replace the Face Plate, making sure the Face Plate is
fully sealed.
• Position the Water Leak Sensor where desired.
•
•
•
•
LED INDICATIONS
Solid at power up:
Initializing, checking for Factory Reset
3 red flashes then pause:
Searching for network to join
FCC STATEMENTS
SALUS WARRANTY
WARNING: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
SALUS North America, Inc. (“Salus”) warrants that for a period of five (5) years
(“Warranty Period”) from the date of purchase by the consumer (“Customer”),
this device, excluding batteries (“Product”), shall be free of defects in materials
and workmanship under normal use and service in accordance with all supplied
instructions. During the warranty period, Salus shall, at its option, repair or
replace any defective Products, at no charge for the device. Any replacement
and/or repaired devices are warranted for the remainder of the original
Warranty Period or ninety (90) days, whichever is longer.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
This warranty does not cover removal or reinstallation costs. This warranty does
not apply to any Product (i) which has been modified, repaired, or altered,
except by Salus or an authorized Salus representative, (ii) which has not been
maintained in accordance with any handling or operating instructions supplied
by Salus, or (iii) which has been subjected to unusual physical or electrical stress,
misuses, abuse, negligence or accidents.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
SALUS SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,
EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states
and provinces do not allow the exclusion or limitation of incidental or
consequential damages, or limitation on the duration of implied warranties of
merchantability or fitness, so these exclusions or limitations may not apply to
you.
FCC AND INDUSTRY CANADA
SPECIFICATIONS
Operating Conditions
32–104°F / 0–40°C
20–90% humidity (non-condensing)
Storage
-4–185 °F / -20–85°C
20-95% humidity (non-condensing)
Protocols Supported
ZigBee HA 3.0
RF Freq.
2.4 GHz
Battery
3V Lithium CR2
IP rating
IP 57
Size
Sensor:
Ø 2.17” x 0.98” /
Ø 55.0 mm x 24.9 mm
Stand:
2.31” x 2.59” x 1.18” /
58.8 mm x 65.9 mm x 30.0 mm
Sensor Cable Length:
78” /
2m
RF Radiation Exposure statement: This equipment complies with FCC and
Industry Canada RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum
distance of 20 centimeters between the antenna and all persons.
INDUSTRY CANADA
This device complies with Industry Canada's licence-exempt RSSs.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada .
Son fonctionnement est soumis aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This warranty is the only express warranty Salus makes for the Product. Any
implied warranties, including warranties of merchantability or fitness for a
particular purpose, are limited to the Warranty Period or the shortest period
allowed by law.
No oral or written information or advice given by Salus or a Salus-authorized
representative shall modify or extend this warranty. If any term is held to be
illegal or unenforceable, the legality or enforceability of the remaining terms
shall not be affected or impaired.
Customer’s sole and exclusive remedy under this limited warranty is product
repair or replacement as provided herein. If a Product under warranty is
defective, the Customer may:
• contact the party (“Seller”) from which the Customer purchased the
Product to obtain an equivalent replacement product after the Seller has
determined that the Product is defective and the Customer is eligible for a
replacement, or
• contact Salus Service at support@salusinc.com, to determine whether the
device qualifies for a replacement. If a replacement is warranted and is
shipped prior to the return of the device under warranty, a credit card is
required and a hold may be placed on the Customer’s credit card for the
value of the replacement until the returned device is verified as eligible for
replacement, in which case, the Customer’s credit card will not be charged.
This warranty gives you specific legal rights, and you may also have other rights
that vary from jurisdiction to jurisdiction. If you have any questions regarding
this warranty, please write Salus at:
SALUS North America, Inc.
850 Main Street
Redwood City, CA 94063
Version 1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Sam Pai
Create Date                     : 2018:06:26 19:22:11Z
Modify Date                     : 2018:07:12 11:38:04+08:00
Subject                         : 
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Format                          : application/pdf
Creator                         : Sam Pai
Description                     : 
Title                           : WLS-QSG ENv1
Creator Tool                    : Word
Metadata Date                   : 2018:07:12 11:38:04+08:00
Keywords                        : 
Producer                        : Mac OS X 10.13.5 Quartz PDFContext
Document ID                     : uuid:624eaade-5772-41ee-b9ee-c5ab2bba04bb
Instance ID                     : uuid:b2d74941-ea68-4979-8c99-2dce6a59c53d
Page Count                      : 2

EXIF Metadata provided by EXIF.tools