SAMSUNG Plasma Television Manual L0411407
User Manual: SAMSUNG SAMSUNG Plasma Television Manual SAMSUNG Plasma Television Owner's Manual, SAMSUNG Plasma Television installation guides
Open the PDF directly: View PDF 
.
Page Count: 99
| Download | |
| Open PDF In Browser | View PDF |
PLASMA DISPLAY
Owner's Instructions
SPP4251
@
@
Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily
designed to view wide screen format fuji-motion video. The images displayed on them should primarily be
in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the
images are constantly moving_ Displaying stationary graphics and images on screen, such as the dark
side-bars on nonexpanded standard format television video and programming, should be limited to no
more than 5% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game
displays,station Iogos,web sites or computer graphics and patterns,should be limited as described above
for aJJtelevisions. DispJaying stationary
images that exceed the above guideJines
can
cause uneven aging of PDP Disptays that Jeove subtJe, but permanent
burned-in
ghost images in the PDPpictureo
To avoid this, vary the programming
and images,
and primariJy dispJay furls€teen
moving images, not stationary
pa_erns or dark bars.
On PDP models that offer picture sizing features, use these controls to view different formats as a full screen
picture.
Be careful in the selection and duration of television formats used for viewing_ Uneven PDPaging as a
result of format selection and use,as well as burned-in images, are not covered by your Samsung limited
warranty.
@ ScreenJ_age retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP)on the plasma
display panel for more than,several minutes as it can cause screen image retention. This image retention is
also known as screen burn _To avoid such image retention, refer to page 40 of this manual to reduce the
degree of brightness and contrast of this screen when displaying a still image.
@ CdJJ)efect
The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9
percent active cells, there may be some cells that do not produce light or remain lit.
@ Altitude
The PDP wiJJnot operate normally at altitudes above 6500 ft.
@ Warranty
Warranty does not cover any damage caused by image retention.
Burndn is not covered by the warranty.
i
i
0
¸¸¸¸
..................
(ha#rid (o#trd
Generd N{ormation
Your New Plasma Display Panel ......................
6
Fine Tuning Channels ..................................
64
Remote Control Buttons ..................................
8
LNA (Low Noise Amplifier}
65
V'/all Installation Instructions ..........................
10
How to assemble the Stand-Base ..................
14
..........................
(ennectinga ?( undOperatien
Connecting a PC ........................................
68
Adjusting the PC Screen ..............................
72
Connecting VHF and UHF Antennas .............. 16
Changing the Position of the Image ................
73
Connecting Cable TV ..................................
17
Picture Quality Adjustment
74
Connecting a VCR ......................................
19
information
Connecting a Camcorder
............................
20
Connecting a DVD Hayer ............................
21
_me Setting
Connecting a DTV Receiver ..........................
22
Setting the Clock
Turning the PDP On and Off
........................
..........................
................................................
........................................
77
80
Setting the Sleep Timer ................................
81
Setting the Timers ........................................
82
24
Hug & Hay Feature ......................................
26
Functien#esc@tien
Memorizing
29
Selecting a Menu Language
34
Digital Noise Reduction
..............................
87
.............. 36
Selecting the Film Mode
..............................
88
Setting the Melody Sound ............................
89
Setting the Blue Screen ................................
90
40
Viewing Closed Captions
91
41
Using the %Chip ..........................................
the Channels ............................
Setting Up Your Remote Control ....................
Viewing an External Signal Source
?ictsr÷ (#ntrd
Customizing the Picture
..............................
Using Automatic Picture Settings
..................
Selecting the Color Tone ..............................
DNJe (Digital Natural Image engine)
Changing the Screen Size
Freezing the Picture
............................
86
92
42
............ 43
..........................
...................................
Viewing the Picture-in-Picture
........................
.......................
44
Troubleshooting
........................................
46
Care and Maintenance
47
Specifications ............................................
..............................
1O0
101
102
Selectinga SignalSource(Antennaor Cable)for PIP ..... 52
Sound(ontrd
Customizing the Sound ................................
56
Using Automatic Sound Settings ...................
57
Choosinga Multi-ChanndSound(MTS}Soundtrack...... 58
Using the Auto Volume ................................
59
Setting the TruSurround XT ............................
60
Listening
totheSound
oftheSub(PiP)
Picture
(PCorDVIMode)....61
Selecting the Internal Mute ............................
62
3
Your New Plasma Display Panel ......................................................
Remote Control Buttons ..................................................................
6
8
Wall Installation instructions ..........................................................
10
How to assemble the Stand-Base ....................................................
14
Speakers
Remete(oetrd $iged Receiver
Aim the remote control towards
this spot on the PDR
SOUR([Button
Press to turn the PDPon and off.
Power Jedicator
- Power Off: Blue
Power On: Off
Pressto display all of the available video sources
(TV, AV1, AV2, AV3, S-VIDEO1, S_VIDEO2,COMPONENT1,
COMPONENT2, PC, DVJ).
MENU be||oe
Displays the main on-screen menu.
VOL(+,o)button
Press to increase or decrease the voJume_Also used to
select or adjust items on the on-screen menu.
(H(..-,,v)
Better
Press CH/", or CHv
to change Channels.
Also used to move up or down in the On-screen menu.
ENTER(
C_ ) button
Press to confirm a selection
Once you have unpacked your PDP,check to make sure that you have all the parts shown here.
Jfany piece is missing or broken, call your dealer.
Sotd Separafet_
Owner'sInstructions
(BN68-00618A)
0
Remote
ControJ/A,S,A
Batteries
(BNSg-00377D/
PowerCord(3903-000144) AntennaCaNe(BN39-00333A)
S-ViDEO Cable
PC Cable
DVI Cable
Component
Cables(RCA)
PC Audio Cable
@DVJiNPUT(DVFD/ L-AUDiO-R)
Connect to the digital video and audio
output jack for device with DVI output.
@ MONITOROUT(VIDEO/ L°AUgJO-R)
Outputs for external devices
@ P( JNPgT(RGgJN/ AUgJO}
Connect to the video and audio output
jack on your PC.
@Avl, Av2,Av3
(VmDEO
/ L-AUDmO-R
)
Video and audio inputs for external
devices, such as a camcorder or VCR.
@ (OMPONENI"I,(:OMPONENI"2
Video (Y/Pb/Pr) and audio (L-AUDIO-R)
inputs for Component.
@ ANTmNVHFiUHF(75£_}
75£-2Coaxial connector for
@ FORSERVJ(E
ONlY
Antenna/Cable
Network.
Connector for service only.
0 POWER
iN
@ S°VJDE01,
S°VJDE02
(S°VJDE01
or S-ViDE02/ L-AUDJO°R}
Connect the supplied power cord.
Video and audio inputs for external
devices with an S-Video output, such as
a camcorder or VCR.
7
@ POWER
button
Turns the PDP on and off.
@ ASPECT
butten
Press to change the screen size.
@ Numberbuttons
@
@ +100 butl0n
Press to select channels over 1OO. For example, to select
channel 121, press "+1OO", then press 2 and 1.
Press to mute the PDPsound.
@
@ VOL(Vdu_u} buttous
Use it to adjust volume.
Press to select a preset time interval for automatic shutoff.
@ MENUbutton
Displays the main on-screen menu.
Confirms a selection.
0 PiPbutton
Activates picture in picture.
@ STILLbuttou
@
iii!il
÷
@
@
@
@
@
Press to pause the current screen.
L@ J)ispJay
When you press a button, '_>' appears along with
selected mo'de (TV, VCR, CATV, DV"Dor STB}and
remaining batteries on LCD.
@ BMOJ)Ebutt0u
@
Adjust the PDP picture by selecting one of the preset
factory settings (or select your personal, customized
picture settings.)
@ MOJ)Ebutlou
Selects a target device to be controlled by the Samsung
remote control ie, VCR, Cable, DVD players or STB.
If you change modes, the new mode is momentarily
displayed on LCD.
@ PRE-CHbutlou
Tunes to the previous channel.
@ TViVJDEObultou
Press to display alJ of the available video sources
TV AV1 AV2 AV3 S_VIDEO1 S-ViDEO2 COMPONENT1
COMPONENT2, PC, DV ,
_]_(H ((hauueJ}butt0us
Use it to switch channels.
@ JHFObutteu
Press to display information on the PDPscreen.
@ EXiTbutt0u
Press to exit the menu.
@ L_p/J)_wu
Ldt/Rightbutteus
Control the cursor in the menu.
i
i_ i
i
@SRS TSXTbBtto.
Selects Trusurround XT mode.
VOL
0
CH
MTS bBttoe
Press to choose stereo, mona or Separate Audio Program (SAP broadcast).
@ AUTO PRO& Bett0e
The TV automatically cycles through aJJof the available channels and stores them in memory.
@ ADDiDELBett0e
Press to add or delete channels in the TV's memory.
@ DNb Bett0e
Activates DNle (Digital Natural Image engine).
i!i ÷:!%
@ (APTION
Beit0e
Controls the caption decoder.
:}
STILL MTS SRSTSXT
@ SETbett0e
Used durinq set up of this Samsung remote control,
so that it will work compatibly witB other devices
(VCR, cable box, DVD}
© PiPc0.trd bett0es
SWAP
: Exchanges the video signal that is
currently displayed on the main screen
with the signal in the PIPwindow.
SIZE
: Press to make the PIPwindow Large,
Small or Double.
CH,A,,\J
: Displays the available channels in
sequence_ (These buttons change channels
in the HP window only).
© V(R,DVD €oetrdbettoes
Controls VCR tape or DVD disc functions: Stop,
Rewind, Play/Pause, Fast Forward.
[f your remote control is not functioning properly, take
out the batteries and press the reset button for about
2_-3 seconds. Rednsert the batteries and try using the
remote control again.
cover
1 toSlideopenthethebackbattery
compartment of the
remote controk
Remote (0etrd
Install _'o AAA size batteries. Make sure to match the
"+" and "-" ends of the batteries with the diagram
inside the compartment.
Slide the cover back into
place_
Operati0e Range°
You can use your remote control within a distance of 23 feet and an angle of 30 degrees
from the Jeff and right sides of the PDP's remote control receiver.
9
Do not install the PDPon any location other than a vertical walk
To protect the performance of the PDPand prevent problems, avoid the following locations:
" Do not install next to smoke and fire detectors.
', Do not install in an area subjected to vibration or high voltage.
o Do not install near or around any heating apparatus.
Use only recommended parts and components.
i
Thiswdl mountbracket
instdl_ti0n
guideisforthefollowing
model:SPP4251
WdJ Meunt Bracket
Insulation Holder ; 4 EA
10
Screws ; 4 EA
PDP to
1
Remove the screws from the back of the PDP.
T
Connect insulation holders to screws (see the illustration below}.
• If you are uncertain about installation, hire a specialist to install the waJJmount bracket.
,, Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wail mount bracket.
o Be careful to avoid getting your fingers caught during installation.
', Make sure the wail attachment panels are tightened. Otherwise the PDP may faik
3
Tighten the screws of the insulation holders to the back of the PDP.
T
@
"
A 5 inch gap is needed between the back of the Plasma TV and the waik
11
Put
4 insulation
holders toonsecure
the PDP
thewall
grooves
of bracket
the wall (@1mount
bracket
pull the
down
on the PDP(@)
it tointhe
mount
Tighten
theand
screws as shown (@1 so that the PDP cannot be separated from wall mount bracket.
PDPpanel _//
O--_,
I_.
i
O
Wall
Wall attachment panel bracket
to PDP
To connect external devices such as a DVD or a Home Theater System to the PDP,
please refer to following instructions:
Be sure to remove the safety pins underneath the PDP.
o If the safety pins are not removed, the angle cannot be adjusted.
Any attempt to do so may cause damage to the PDP.
Pull out the bottom of the PDP(which has been attached to the Wall Mount Bracket)
in the direction indicated by the arrows (refer to the illustration/until it clicks.
Using the PDPAfter Connecting External Devices.
Be sure to secure the PDPby inserting the 2 locking pins after readjusting the
angle of the PDPto 0 °.
For safety, be sure to secure the PDPusing the locking pins.
If the safety pins are not used, the PDP may fall, causing serious injury.
20.0°+2.0
12
°
to ust
Facterydda@
The wall mount bracket is delivered separately_ Please tighten the captive screw in the
direction of the arrow after assembling the bracket.
Changingthe angle
Secure the
PDP torefer
the to
wallthemount
bracket.
(Please
following
instructions.)
Set
by pulling
the upper
of
the the
PDPangle
attached
to bracket
in the end
direction
of the arrow.
The
angle
can be adjusted from 0 ° to 15 °
o
by ÷_2.
13
Assemble
twousing
support
pins with
the stand base and firmly secure both sides of the
support pins
8 screws
provided.
Assemble the PDPwith the stand and firmly secure the PDP using 4 screws provided.
Twoor morepeople
should
_orrytirePBRNeverlaythePBPontirefloorbecause
ofpossible
damage
tothescreenAlways
storethePBPupright
14
iiiiiiiiiiiiiiiiii!!iii
Connecting VHF and UHF Antennas
..............................................
16
Connecting Cable TV....................................................................
17
Connecting a VCR ........................................................................
19
Connecting a Camcorder ..............................................................
Connecting a DVD Hayer ..............................................................
20
21
Connecting a DTV Receiver ..........................................................
22
If your antenna Jooks Jike this:
1
it has 75-ohm round Jeads.
Hug the antenna Jead into the VHF/UHF terminaJ
on the PDP.
Use the Anter na Cabe, an accesso/y nc uded
n the p/oduct package,
16
You can connect different cable systems to your PDP, including cable without a cable box,
and cable with a cable box that descrambles some or all channels.
1
Plug the incoming cable into the VHF/UHF terminal on
the PDff
Use fl_e Anterma Cabe, an acces o/y _c uded
fl_e p/oduct package.
Find the cable
connected
to the
OUTbe
terminal
on your
cable box.
ThisANTENNA
terminal might
labeled _ANT OUT_, _VHF OUT _ or simply _OUT_L
Connect the cable to the VHF/UHF terminal on the
PDP.
Uetf_eAnternaCa:_e,
anacc_.,
n tf_e p/cduct package.
/y': ncud_d
17
To complete this connection you will need a _'o-way splitter, an RF (A/BI switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the cable that is connected to the ANTENNA IN terminal of
your came box.
This terminal might be labeled "ANT IN",
"VHF IN" or simply, "IN". Connect this
cable to a two-way splitter.
ANTENNA
..................................................
_-nn_b-_"
,ooom,o0
Cable
Splitter
Connect
a coaxial
PUT terminal
of the cable
splitterbetween
and the an
IN OUTterminal of the cable box.
Incoming
Cable
Splitter
Cable Box
ANTENNAa coaxial
Connect
OUT terminal
cable between
of the cable
the box
and the B-IN terminal of the AiB switch.
Incoming
Cable
Splitter
RF (A/B)
Switch
Cable Box
Connect
cable be_'een
the box
ANTENNAa coaxial
OUT terminal
of the cable
and the B-IN terminal of the A/B switch.
Incoming
Cable
Splitter
RF (A/B)
Switch
Cable Box
Connect
the last
cable switch
between
OUT terminal
of coaxial
the RF (A/B)
andthe
the VHF!UHF terminal on the PDP.
Incoming
Cable
Spl_tter
RF
Cable
Box
(AJB)
Switch
After you've made this connection, set the A/B switch to the "A" position for normal viewing.
Set the A/B switch to the "B" position to view scrambled channels. (When you set the A/B switch
to "B", you will need to tune your Set-Top Box to the cable box's output channel, which is usually
channel 3 or 4.}
18
OF
PDP
?
Power Plug
Audio Cable
S_Video Cabk
or
Connect the Video/Audio
AUDIO!VIDEO
cables between the AUDIO(L/R)/VIDEQ
Video Cable
J
jacks on the PDPand
OUT jacks on the VCR. (Note: For better video, you can usean S-Video cable.)
VideotapePJayback:
1. Turn on your PDP.
2. Press the TV!VIDEO button to select "Video" or "S-Video
3. Turn on your VCR, insert a videotape and press the play button.
19
Camcorder
PDP
i
Power Plug
Video Cable
Audio Cable
Connect a Video!Audio
VIDEO!AUDIO
cable be_'een the AUDIO(L/R)/VIDEO
jacks on the PDP and the
OUTPUT jacks on the camcorder.
Viewing Tapes
1. Turn on your PDP.
2.
Press the TV!VIDEO button to select "Video".
3. Turn on your camcorder and set it to Video Mode. (For details, refer to your camcorder
Owner's instructions.)
20
4.
Set the IN/OUT
switch on your camcorder to OUT.
5.
Insert the tape into the camcorder and press the Play button.
This PDP displays the optimum picture in 720p mode.
PDP
DVD P{ayer
...............
_.;!j"'_ _:.....................................................
®®e®®¢
.........
] . ......
Power Plug
Audio Cable
1 Connect a Video Cable between the Y, Pb, P, (COMPONENT1,2)
and Y!PB!PRoutput jacks on the DVD player.
2 Connect a Audio Cable between the AUDIO L/R(COMPQNENT1,
and the AUDIO OUT jacks on the DVD player.
input jacks on the PDP
2) input jacks on the PDP
ToPJayDVD:
1_ Turn on },our PDP.
2.
Press the TV!VIDEO button to select "COMPONENT1
" or "COMPONENT2".
3.
Turn on your DVD player, insert a DVD disc and press the Play button.
For an explanation of Component video, see your DVD owner's instructions.
21
1
This PDPdisplays the optimum picture in 720p mode.
PDP
DTV Re0eJver
O @@
®
OF
Audio Cable
DVi Cable
Use a DVi-D connection cable. (said separately}
1 Connect the cable or antenna to the antenna input jack on the DTV.
2 Connect a Video cable between the Y, P_,,P, (COMPONENT 1,2] or DVI jack on the PDP
and the Y, P_,PR(VIDEO OUTPUT JACKS) on the DTV receiver.
3 Connect an Audio came between the COMPONENT 1,2 (LiR AUDIO] or DVI jacks on the
PDPand the AUDIO OUTPUT jacks on the DTV receiver.
ToWatchDTY:
1. Turn on your PDP.
2.
Press the TV!VIDEO button to select "COMPONENT1
3.
Turn on your DTV receiver.
", "COMPONENT2"
or "DVI".
For an explanation of Component video, see your DTV receiver owner's instructions.
Turning the PDPOn and Off ..........................................................
24
Hug & Hay Feature ......................................................................
26
Memorizing
29
the Channels ..............................................................
Setting Up Your Remote Control
....................................................
34
Viewing an External Signal Source ................................................
36
Off
PDP
Press the POWER button on the remote controk
The PDPwill be turned on and you will be ready to use its
features_
You can also use the POWER (R/O)button on the front of the
PDR
Notes:
If your PDP isn't turned on when the power button is
pressed: Press the_button
to check if the TV mode
has been chosen (
).
Your PDP has a simple, easy_to_usemenu system that appears on the PDP screem This system makes it
convenient and fast to use features on the PDP.Your PDPalso Jetsyou display the status of many of your
PDP's features.
Viewing the Menus
With
power The
on, main
press menu
the MENU
button
on screen.
the
remotethe
control
appears
on the
The Input menu is selected.
2
Press the A or T buttons to move items in the menu_
Press the 4/I_/ENTER
buttons to display, change, or
use the selected items_ Press the ENTER ( (Z_ / button to
enter items in the menu_ On screen menus disappear
from the screen automatically after about thirty seconds,
or you can press the MENU or EXITbutton on your
remote control to exit the menu.
STILL MTS SRSTSXT
24
DispJeyieg Status Je[ermetiee
Press the INFO button on the remote controk
The PDPwiJJdisplay the Picture mode, Sound mode, MTS,
Caption, and Clock.
25
When the television is initially powered ON, several basic customer settings proceed
automatically and subsequently. The following settings are available.
If the television
is inthe
Standby
POWER
button on
remote mode,
controkpress the
++++++++
Themess+goStortPlug&P[oy+sd+sploye&
it fl++kers
foro l+tt[+
wh++++
0ndthentheL0ngu0g+
menu+s0utom0tkd+y
d+sp[0t,
ed+
Select the appropriate
A or ++ button+
language by pressing the
++++++++
Themessog+€he&0ntenn0
inputisdispl0yed+
Press the ENTER button to confirm your choice+
Press the ENTER button+
26
Select
the correct
signal
source
(Air, STD, HRC and
[RC}, then
press the
ENTER
button.
6
To start the search, press the ENTER button.
Theseor_h
willendoutomotkdly.
{honndsaresortedondstoredin
onorderwhkhrefle_stheirposition
in thefrequency'
ronge(with
lowest
firstandhighest
lost)+
When
it hosfinished,
the@_&Setmenuisdisplayed
TostoptheseorCh
beforeit hosfinishedor returnto normal
viewing,
press
theMEHU
button_
Press
Press the
the ENTER
_ or m button.
button to move to the Hour, Minute,
or am/pm.
Set the Hour, Minute, or am!pm by pressing the
,L or T button.
When
it has
finished, the
Enjoy which
your
watching
is displayed,
andmessage
the channels
have been stored can be viewed.
27
If you want to reset this feature...
Press the
MENUthen
buttom
the A or T button to
select
"Setup",
pressPress
the ENTERbutton.
Press the A or T button to select "Miscellaneous",
then press the ENTER button.
A or _' button.
button to select "Plug & Play".
Press the ENTER
For furtherpage.
details on how to set, refer to the
previous
28
Your PDP can memorize
(antenna} and cane
CH ,_ and CH v
and store alJ of the availab[e
channels
for both "off-air"
channels. After the available channels are memorized,
use the
buttons to scan through the channels. This eliminates the need to
change channels by entering the channel digits. There are three steps for memorizing
channels: selecting a broadcast source, memorizing the channels (automatic / and
adding and de)eting channe)s (manua)).
Before your tdevision
can begin
memorizing the available channels, you must specify the type of signat
source that is connected to the PDP (i.e., an antenna or a cable system}.
Press
MENU button_
Press
theENTER
_ or Vbutton.
button to
select the
"Channel",
then press
the
Press the ENTERbutton to select "Air/CATV'.
3
Press the A or T button to select "Air", "STD",
"HRC" or "IRC'L
o If you are connected to an antenna, leave "Air"
displayed. If you connected cable, press the
A or Ir button to the display the type of cable
system: "STD", "HRC" or "IRC".
(If you are nat sure which type of cable system you
have, contact your cable company !.
Press the MENU button to exit.
e STD, HRC and IRC identify various types of cable TV systems. Contact your IocaJ cable company to
identify the type of cable system that exists in your particuIar area. At this point the signaI source
has been selected. Proceed to "Storing Channds in Memory" (Next page}.
29
1
First, select the correct signal source (Air, STD, HRC
and IRC)_See steps on previous page_
Press the MENU button. Press the A or T button to
select "Channel", then press the ENTER button.
2
Press the A or T button to select "Auto Program",
then press the ENTER button.
i
3
Qui_k
w_ytoa_esstheAut0m_tk
Ch_nnd
Setting:
_ustpress
the
"AUTO
PROG"
buttonontheremotec0ntrd
Press the ENTER button.
The PDPwill begin memorizing all of the available
channels.
After all the available channels are stored, the Auto
program menu reappears. Press the ENTER button to
stop.
'_ The PDPautomatically cycles through all of the available channels and stores them in memory.
This takes about one to _o minutes.
30
,g
g
Use wiJJ
the number
buttons
to directly select the channel
that
be added
or deleted.
Ex} Channel "4"
Press the ADDiDEL button, then press the ENTER
button. Repeatedly pressing this button wiJJalternate
between "Add" and "Delete".
Press the MENU button to exit.
', You can view any channel (including an erased channel} by using the number buttons on the
remote control.
31
(Prop
Press
MENU buttom
Pressthe
theENTER
A or _'button.
button to
sdect the
"ChanneJ",
then press
Press
the A button.
or T button to seJect "Scan", then press
the
ENTER
Only the memorized channeJs are chosen.
Press the MENU button to stop.
32
Pressthe CHA
or CHv
button to change channels.
When you press the CHA or CHv
button, the PDPchanges channels
in sequence. You will see all the channels that the PDPhas memorized.
(The PDPmust have memorized at least three channels.)
You wilt not see channels that were either erased or not memorized.
Pressthe number buttons to go directly to a channek For example, to select
channel 27, press "2" then "7". The TV will change channels when you
press the second number.
When you usethe numberbuttons,you can directly sebct channelsthat were
either erasedor not memorized. Tochange to singbdigit channels(0_9) bster_
press "0" bebre thesingle digit. (Forchannel "4" press "0", then "4".
Pressthe PRE-CHbutton. The TV wiJJswitch to the last channel viewed.
Toquickly switch between two channels that are far apart, tune to one
channel, then use the number button to select the second channel. Then,
use the PRECH button to quickly alternate between them.
Pressthe VOL + or VOL - button to increase or decrease the volume.
At any time, you can temporarily cut off the sound using the MUTE button.
Press
the MUTE
and theinsound
cuts off_
The
word
"Mute"button
wiJJappear
the lower-left
corner of the screen.
To turn mute off, press the MUTE button again, or
simply press the VOL + or VOL - button.
33
This PDVs remote control can operate almost any VCR, cable box or DVD. After it has been set up
properly, your remote control can operate in four different modes :TV, VCR, Cable, DVD or STB_
Pressing the corresponding button on the remote control allows you to switch be_'een these modes,
and control whichever piece of equipment you choose.
N>lc, : _ i_fl_:, female, _':o _'poJ racy _o J e _':o _pa b/e w i'h a// D VD P/c/e_s, VCRs, Cable loxes
7/e remot_ co_'l;oJ can o _f}_ope ate S)'}_:imade by Samsung
Setting Up the Remetete Operate YeurV(R, Cablebex er DVD player
Turn off your VCR. (or Cable box, DVD player}
Press
MODE
button. Mode is changed whenever
MODEthe
button
is pressed.
3
Press the SETbutton on your TV's remote control.
_osz
4
Using the number buttons on your remote control,
enter three digits of the VCR (or Cable box, DVD
player) code listed on page 35 of this manual for
your brand of VCR (or CATV, DVD). Make sure you
enter three digits of the code, even if the first digit
Js a _0 _.
(If more than one code is listed, try the first one.}
5
Press the POWER button on the remote controk
Your VCR (or CATV, DVD) should turn on if your
remote is set up correctly. If your VCR (or CATV,
DVD} does not turn on after setup, repeat steps
2, 3, and 4, but try one of the other codes listed for
your brand of VCR (or CATV, DVD).
If no other codes are listed, try each code, 000
through 089 (or Cable box: 000 through OZZ,
DVD player: 000 through 008}.
Nofe_
When your remote control is in "VCR" mode, the VCR control buttons (STOP, REW, PLAY!PAUSE_FF)
still operate your VCR.
When your remote control is in "CATV" or "DVD" mode, the VCR control buttons (STOP, REW,
PLAY!PAUSE, FF) still operate your VCR.
You do not need to program the remote for Samsung STBsas the codes are pre-programmed.
34
Remote{ontrd Codes
VCR Codes
Brand
Codes
Admiral
Aiwa
Akai
020
025
027 004 032
Audio Dynamics
007 026
Bell &Howet!
018
Broksonic
022
Candle
002 006 003 015 008 055
Canon
021 056
Citizen
002 003 006 008 015 055
Co!ortyme
Craig
Curtis Mathes
Daewoo
DBX
Dimensia
Dynatech
Emerson
002
002 017 007
021 025 056 064
003 015 010 011 {)!2
014
007
001 003 006 021 022
030 032 034 040 047
052 060 063 065 066
Fisher
018 024 028 029 048 051
Funai
General Electric
017 002
005
Go Video
LG(Goldstar)
006 007 008 009
Harman Kardon
Hitachi
019 025 041
InstantReplay
]C Penny
007
024
008
066
013
016
026
017
034
025
050
067
069
061
025
021
056
002
010
007
042
021
002 007 018 019 021
026 037 041 054 056
Brand
JVC
Kenwood
KLH
Codes
007 008 018 021 026 037
007 008 018 026 037
070
Lloyd
Logik
LXI
Magnavox
Marantz
Marta
MEI
Memorex
MGA
Midland
Minolta
Mitsubishi
025
038
025
021 036 056 059
008 007 018 021 026 036
037 062
006
021
006 021 024 025
034
005
019 041
019 034 041 046
Montgomery
Ward
020
MPC
002 025
Multitech
002 025 038 005
NEC
018 007 026 037 008 062 064
Optimus
Panasonic
Pentax
Pentex Research
Philco
020
021 056 071 072
019 041
008
021 036 056 059
Philips
021 036
Pioneer
019 026 039 053
Portland
015 049 055
PROSCA N
017
Quartz
018
Quasar
021 056
Radio Shack/Realistic
006 018 020 021 024 025 029 034 048 056
Brand
Codes
RCA
017 019 002 021 035 041 043 057 068
Samsung
Sansui
Sanyo
Scott
Sears
000 001 002 003 004 005
026
018
003 047 052
018 0!9 006 024 028 029
048
Sharp
Shimom
024
067
041
051
020 034 045 015
027 033 038 058
Signature,
Sony
Sylvania
Symphonic
-Iandy
_lhshika
025
027 033 044
021 025 036 056 059
025
018 025
006
Tatung
Teac
7bchnics
TPknika
TMK
_bshiba
-Ibtevision
Unitech
VectorResearch
Victor
037
025 037 068
021
021 006 025 031
066
003 019 029 051 052
002 006
002
007 026
026
Video Concepts
Videosonic
Wards
002 003
024
Yamaha
007
Zenith
006
025
008
023
019
034
018
027
007 026
002
020 021
038 041
026 037
033 073
CaMe Box Codes
Brand
Anvision
GI
Hamlin
Hitachi
Jerrold
Macom
Magnavox
Oak
Panasonic
Codes
017 018
041
003 024 031
025 030
038 039
025 030
019 023 028
026
003 022 027 037 044
grand
Philips
Pioneer
RCA
Codes
019 021 023 {)28
0!8 020 004 044
014 022 040
Regal
Regency
SA
003
015 023
042 043
Samsung
000 001 002 003 004 005
006 007
Atlanta
042 043
Scientific
Brand
Sprucer
Stargate
Codes
2000
Sylvania
_lbxscan
Tncom
Universal
Viewstar
Warner amex
Zenith
{)22
036
016
016
032
033 034
019 021 023 028
046
017 029 035 037 045
DVD Codes
Brand
Samsung
JVC
PROSCAN
RCA
LG(Goldstar)
Sony
Denon
Curtis
Mathos
Codes
000 001
002
003
003
006
007
008
009
35
Use the remote control to switch between viewing signals from connected equipment,
such as VCRs, DVD, Set-Top box and the TV source (broadcast or cable}.
Press the
MENU button. Press the ENTER button to
select
"Input".
Press the ENTER button to select "Source List".
Press
or _ button to select signal source, then
press the
the AENTERbutton.
Notes
o When you connect equipment to the PDP,you can choose between the following sets of jacks:
AV1, AV2, AV3, S-Video1, S_Video2, Component1, Component2, Monitor Out, PC or DVI on the
PDP'srear panel.
36
t0
put
Press
MENU button. Press the ENTER button to
select the
'qnput'.
Press the A or _ button to select "Edit Name", then
press the ENTER button.
3
Press the ENTER button.
o Press the A or T button to select external device:
VCR, DVD, Cable STB, HD STB, Satellite STB,
AV Receiver, DVD Receiver, Game, Camcorder,
DVD Combo, DHR or PC_
Set other signal sources (AV2, AV3, S_Videol,
S_Video2, Component1, Component2, PC or
DVI) using the same method as listed above.
Press the MENU button to exit.
_te_
o DHR : DVD HDD Recorder
37
Customizing the Picture ................................................................
40
Using Automatic Picture Settings ....................................................
4]
Selecting the Color Tone................................................................
42
DNIe (Digital Natural Image engine)
43
............................................
Changing the Screen Size ............................................................
44
Freezing the Picture ......................................................................
46
Viewing the Picture-in-Picture ..........................................................
47
Selecting a Signal Source (Antenna or Cable 1for PIP........................
52
You can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color,
and Tint settings of your PDP.
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Picture",
press
the the
ENTER
2
Press the A or _ button to select "Custom", then
press the ENTER buttom
You wiJJaJso see the items "Contrast", "Brightness",
"Sharpness", "Color" and "Tint".
3
Press the A or T button to select the item you wish
to change, then press the ENTERbutton.
Press the _ or _ button to change the value of the
item.
Press the MENU button to exit.
o In the PC!DVI mode, you can't adjust the Color and Tint.
40
Your PDP has automatic picture settings that allow you to adjust the video display easily.
Press
MENU then
button.
Press
A orbutton.
T button to
select the
"Picture",
press
the the
ENTER
i
Quirkw0yto 0_essthepktur÷setHng:
Justpress
tl_÷"RMODE"
tJutton
ontheremote
r0ntrd.
Press the ENTER button to select "Mode".
3
Press the _ or T button to select "Dynamic",
"Standard", "Movie", "Custom" picture setting.
o You can select "Custom", "Entertain", qnternet",
or "Text" in PC!DVI mode.
Press the MENU button to exit.
41
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Picture",
press
the the
ENTER
Press the A or _ button to select "Color Tone", then
press the ENTER button.
3
Press the A or T button to select "Cool2", "Cool1",
"Normal", "Warm 1" or "Warm2".
o You can select "Custom", "Cool", Normal" or
"Warm" in PC mode_
o You can select "Cool", "Normal" or "Warm"
in DVI mode.
Press the MENU button to exit.
42
Samsung's New Technology brings you more detailed images with contrast,
white enhancement and 3D noise reduction.
Press
MENU then
button.
Press
A orbutton.
T button to
select the
"Picture",
press
the the
ENTER
Qukk,_v_y
t0sdedl/le: Simply
Iressthe"llld' tutt0nund÷r
thec0verofthe_em0te
c0ntrd.
Press the A or T button to select "DNle',
the ENTER button.
then press
Press the ,L or _ button to select "On", "Off" or
"Demo".
oOn : Switches on the DNle mode.
',Off: Switches off the DNle mode.
', Demo : The screen before applying DNle appears
on the right and the screen after applying
DNle appears on the left.
Press the MENU button to exit.
43
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Picture",
press
the the
ENTER
Press the A or T button to select "Size", then press
the ENTER button.
Press the ,L or _" button to select the screen size you
want.
Press the MENU button to exit.
', If you watch a still image or the 4:3 (Normal} mode for a long time (over 2 hours}, an image may
be burned onto the screen.
View the monitor in 16:9(Wide} or Panorama mode as much as possible.
44
16:q(Wide)
16:9 Aspect Ratio that fits DVD and Wide Screen
applications.
JU
PanlQFa Jn_u
Fits a 16:9 picture onto a 4:3 screen and displays
it without clipping the image.
JJ
ZQQm
Magnifies the 16:9 wide picture (in a vertical
direction/to fit the screen size_
Select _S_by pressing the _ or _ buttom
Use the A or _r button to move the picture up and
down. After selecting
use the A or T button
to magnify or reduce the picture size in a vertical
direction.
4 : 3(NQr d)
Standard TV and VCR screen size having a 4:3
Aspect Ratio_
o In TV, VIDEO, S_VIDEO and Component (480i) modes, aJJscreen modes can be selected.
(16:9 -_ Panorama -_ Zoom _ 4:3)_
o In PC/DVI mode, only 16:9 & 4:3 modes can be selected_
In Component (480p, 72%.
1080i) modes, Panorama mode can't be selected_
In Component (480p, 720p_ 1080i) modes, you can move the picture on screen by pressing
the A or T button. (All screen modes)
Changing the screen size to Normal, or Zoom during PIP mode wiJJcause the PIPwindow to
disappear.
45
Sti{{
Press the STILLbutton on the remote control to freeze a
moving picture. Pressagain to cancel.
46
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Picture",
press
the the
ENTER
Qui_k
wsyt_ _÷ssthePIPmode:lustpress
tl_÷"PIP"tJutt0n
0n
theremote
control.
Press
or _' button.
button to select "PIP", then
press the
the A
ENTER
3
Press the ENTER button, then press the A or T
button to select "On". The PIPimage will appear in
the corner of the screen.
', Pressing the A or T button will alternate between
"On" and "Off".
Check if the V-Chip Lock (refer to page 93/is
ON if the PIPOn/Off wiJJ not function. PIPdoes
not function when the V-Chip Lock is set to On.
Change the setting to Off and try it again.
Press the MENU button to exit.
O : PIPand Swap Operate
X :PtP doesn't Operate
PiPSettings
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
X
X
X
X
O
O
O
O
O
O
X
X
X
X
O
O
O
O
O
O
X
X
X
X
O
O
O
O
O
O
X
X
X
X
47
g an
You can use PIPto view a signal from an external source, such as a VCR.
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Picture",
press
the the
ENTER
Press the A or T button to select "PIP", then press
the ENTER button.
Press the
or T button to select "Source", then
press
the _.
ENTERbutton.
4
Press the A or 'V' button to cycle through aJJof the
available signal sources:
"TV", "AV 1", "AV2", "AV3", "S_Video1 ",
"S_Video2", "Component1 ", "Component2",
"PC" and "DVI".
The signal from these inputs wiJJnot appear if you
have not connected any equipment to the PDP's
respective input jacks.
Press the MENU button to exit.
Note
o The PIPfunction operates in Wide screen.
48
Using Multi-Screen in the Normal or Zoom screen wiJJchange the size of the main screen to Wide
screen.
Prop
Press
MENU then
button.
Press
A orbutton.
T button to
select the
"Picture",
press
the the
ENTER
Qukkw_yto_ess swapping:
lust press
the"SWAP"
buttonunder
thecoveroftheremotecontrd.
Press the A or T button to select "PIP", then press
the ENTER button.
3
Press the A or T button to select "Swap", then
press the ENTER button.
o The image in the PiP window will appear on the
main screen, and vice versa.
Press the MENU button to exit.
49
Prop
Press the
MENU then
button.
Press
A orbutton.
T' button to
select
"Picture",
press
the the
ENTER
Qukkw_yto_ess PIPsize:Justpress
the"SIZE"buttonunder
thec0veroftheremotec0ntrd
Press the A or T button to select "PIP", then press
the ENTER button.
Press
the
ENTER
the A button.
or T button to seiect "Size", then press
Press
the Athe
or ENTER
T button
to select option you want,
then press
button.
Press the MENU button to exit.
50
PiP
Press
MENU then
button.
Press
A orbutton.
T button to
select the
"Picture",
press
the the
ENTER
Press the A or T button to select "PIP", then press
the ENTER button.
Press
or T button.
button to select "Position", then
press the
the A
ENTER
Press
A press
or T the
button
to select
HP position you
want, the
then
ENTER
button.
Press the MENU button to exit.
51
r
if the PiP source is TV while PiP is ON, you can select the broadcasting source of PiP
picture separately from the main picture.
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Picture",
press
the the
ENTER
Press the A or _r button to select "PIP", then press
the ENTER button.
Press the
the AENTERbutton.
or _ button to select "AiriCATV",
press
4
If an antenna is connected, the setting is "Air". If a
Cable TV system is providing the signal, press the
A or '_' button until the appropriate type of cable
system is selected ("STD", "HRC" or "IRC").
Pressthe MENU button to exit the menu.
52
then
PiP
Press
MENU then
button.
Press
A orbutton.
V button to
select the
"Picture",
press
the the
ENTER
Quid<
w0yto d_0nge
thePIP@nnd:gustpress
the CH
"{Iv"
buttonunderthecoveroftheremote
control
or
Press the A or T button to select "PIP", then press
the ENTER button.
Press
or T button.
button to seiect "Channel", then
press the
the A
ENTER
Press
the in
A the
or TPiPbutton
to change the channel that
appears
window.
Press the MENU button to exit.
53
Customizing the Sound ................................................................
56
Using Automatic Sound Settings ....................................................
57
Choosing a Multi-Channel Sound (MTS1Soundtrack ..........................
58
Using the Auto Volume ..................................................................
59
Setting the TruSurround XT ............................................................
60
Listening to the Sound of the Sub(PiP/ Picture (PC or DVI Mode / .......... 61
Selecting the internal Mute ............................................................
62
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Sound",
press
the the
ENTER
Press
or _ button.
button to select "Custom", then
press the
the A
ENTER
3
4
Select the option (volume, balance, equalizer) to
be adjusted by pressing the _ or _ button.
Press the A or T button to reach the required
setting.
Press the MENU button to exit.
i
56
If youm@em_y_h0nges
totheequdize_
seflings,
thesound
Mode
is0utom0ti¢011y
switch÷d
tothecustom
mode
Press
MENU then
button.
Press
A orbutton.
T button to
select the
"Sound",
press
the the
ENTER
Press the ENTER button to select "Mode".
Press the A
or _r button
to select
"Standard",
"Music",
"Movie",
"Speech"
or "Custom"
sound
setting, then press the ENTER button.
Press the MENU button to exit.
57
Depending on the particular program being broadcast, you can listen to stereo, mono, or a
Separate Audio Program_ (SAP audio is usually a foreignJanguage translation. Sometimes
SAP has unrelated information like news or weather.}
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Sound",
press
the the
ENTER
Qukkw0yto0_esstheMTSmenu:Justpress
the"MTS"_utt0non
theremotec0ntrd
Press
the
ENTER
the A button.
or _r button to select "MTS", then press
Press
the Athen
or Tpress
button
selectbutton.
"Mono",
or "SAP",
the to
ENTER
"Stereo"
Press the MENU button to exit.
,
Choose Stereo for channels that are broadcasting in stereo,
,
Choose Mono for channels that are broadcasting in mono, or if you are having difficulty receiving a
stereo signal.
_,
Choose SAP to listen to the Separate Audio Program, which is usually a foreign-language translation,
Note
T'T_e
_
MTS function operates in TV mode only.
58
Each broadcasting station has its own signal conditions, which can make it necessary to
adjust the volume every time the channel is changed_ "Auto volume" Jetsyou automatically
adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.
Press
MENU then
button.
Press
A orbutton.
_ button to
select the
"Sound",
press
the the
ENTER
Presspress
the Athe
or ENTER
_' button
to select "Auto Volume",
then
button.
3
Press the A or T button to select "On", then press
the ENTERbuttom
o Pressing the A or T button wiJJalternate
between "On" and "Off".
Press the MENU button to exit.
59
TruSurround XT is a patented SRStechnology that solves the problem of playing 5.1
muItichannet content over two speakers. Trusurround delivers a compelling, virtual surround
sound experience through any two-speaker playback system, including internal television
speakers. It is fully compatible with aJJmuJtichannei formats.
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Sound",
press
the the
ENTER
Qukkw_yto_¢esstheTruSurr0und
XTmenu:Justpress
the
"SRS
TSXT"
buttonontheremotec0ntrd
Press
or _' button.
button to select "SRS TSXT", then
press the
the A
ENTER
Press
the AororStereo),
T button
to press
change
setting
(Off,
3D
Mono
then
the the
ENTER
button.
4
Press the MENU button to exit.
?ruSurr0und
XT,SRS
mrd((e)) Symbol
r_retrademarks
ofSRS
L@s,Inc
TruSurr0und
×Tte_hnd0gy
isin_0rp0r@d
underlicense
fromSR5
LdJs,Inc.
60
P_nsnt
tofl_nPCor DVImodebyusingtheSOURCE
button
During the PIPfeature is activating, you can listen to the sound of the sub picture.
Press
MENU then
button.
Press
A orbutton.
T button to
select the
"Picture",
press
the the
ENTER
the
Press
ENTER
the A button.
or T' button to select "PIP", then press
Presspress
the Athe
or ENTER
T button
to select "Sound Select",
then
button.
o Pressing the A or V button wiJJalternate between
"Main" and "Sub".
Set to Sub by pressing the A or _' button.
" You can listen to the sound of the sub picture.
Tolistenthesound
ofthemainpidurn,settoMain.
61
i
The internal speakers can be muted in order to hear sound from external speakers
you've connected.
Press the
MENU then
buttom
Press
A orbutton.
_ button to
select
"Sound",
press
the the
ENTER
Press
the Athe
or ENTER
_r button
to select "Internal Mute",
then press
button.
Press
the ENTER
the A button.
or T button to select "On", then press
o Pressing the A or V button wiJJalternate between
"On" and "Off".
Press the MENU button to exit.
62
!i
ii¸¸¸¸¸ ii
Fine Tuning Channels ....................................................................
64
LNA (Low Noise Amplifier) ............................................................
65
Use fine tuning to manually adjust a particular channel for optimal reception.
Press
MENU button.
Press
theENTER
A or Tbutton.
button to
select the
"Channel",
then press
the
Press the A or _r button to select "Fine Tune", then
press the ENTER button.
Press the _ or _ button to adjust the fine tuning.
To
store
fine tuning
the TV's
press
thethe
ENTER
buttomsetting
(A starinicon(*)
willmemory,
appean) To reset the fine tuning to "0", press the T
button to select "Reset", then press the ENTER
button.
Press the MENU button to exit.
64
If the TV is operating in a weak-signal area, sometimes the LNA function can improve the
reception (a low-noise preamplifier boosts the incoming signal}.
Press
MENU button.
Pressthe
theENTER
A or T'
button to
select the
"Channel",
then press
button.
Press the ,L or _ button to select "LNA", then press
the ENTER button.
3
Press the A or T button to select "On", then press
the ENTER button.
o Pressing the A or V button wiJJalternate be_'een
"On" and "Off".
Press the MENU button to exit.
65
ii¸¸¸¸¸ ii
Connecting a PC ..........................................................................
68
Adjusfing the PC Screen ................................................................
72
Changing _he Position of fhe Image ................................................
73
Picfure ©uali_y Adius_ment ............................................................
Information ..................................................................................
74
77
Connection to a Macintosh computer may require an adapter.
POP
Power Plug
Use the DVI-D
connection cable;"
(sold separately!
DVl CaMe
PC CaNe
Audio Cable
PC
DVIj_ck
(Theactualconfigurationon your PC
may be different,
dependingon the
model.)
]
Connect a PC (15pinl cable between the PC Output jack (or DVI jack/on the PC and the
RGB IN(or DVI IN! Input jack (15p D-SUB) on the PDP.
2 Connect a Audio cable be_'een the Audio (RGB or DVI! on the PC and the Audio LiR (RGB
or DVIt input jacks on the PDP.
To_td_ the PCs_reem
1. Turn on your PDP
2.
Press the TV/VIDEO button on the remote control or SOURCE button on the front panel
to select "PC"_
3.
Turn on PC and check for PC system requirements. (Refer to pages 70 and 71 for PC
system requirements.!
4. Adjust the PC screen. (Refer to pages 72 and 74.1
68
Pin
DoSubCable
DVbD Cable (DigitaJoOnJy Connector)
o 15Pin Signal Cable (based on protruded pin}
PC-!UT
Pin No
PC iN
1
Red (RI
Red (R)
1
T.M.D.S.
Data2_
13
T.M.D.S.
2
Green {G}
Green (G)
2
T.M.D.B.
Data2+
14
+5V Power
Pin No
Signal
Assignmenf
Signal
Assignment
Data3+
3
Blue (B)
Blue (B}
3
T.M.D.S.
Data2/4
15
Ground
4
Grounding
Grounding
4
T.M.D.S.
Data41
18
Hot Hug Detect
5
T.M.D.S.
Data4+
17
T.M.D.S.
Data0=
6
DDC
CUoek
18
T.M.D.S.
DataO+
7
DDC
Data
19
T.M.D.S.
Data0/5
8
No Connect
20
T.M.D.S.
Data5=
9
T.M.D.S.
Data1=
21
T.M.D.S.
DataS+
10
T.M.D.S.
Data1+
22
T.M.D.S.
Clock Shield
11
T.M.D.S.
Data1/3
23
T.M.D.S.
Cbck+
J2
T.M.D.S.
Data3=
24
T.M.D.S.
Clock=
5
Grounding (DDC)
6
Red (R) Grounding
Grounding
(DDC)
7
Green (G) Grounding
Green (G) Grounding
8
Blue (B} Grounding
Blue (B) Grounding
Red (R) @aunding
9
Reserved
Reserved
l0
Sync Grounding
Syne Grounding
1]
Grounding
Grounding
12
Data (DDC)
Data (DDC)
13
Horizontal sync.
Horizontal sync.
14
Vertical syne.
Vertical sync.
15
Clock (DDC)
Clock (DDC)
Shield
Pin No
Shield
(for +5V)
Shield
up PDP(
Our adoption of the new VESA® Plug and Play solution eliminates complicated and time consuming
setup. It aJiow's you to install your monitor in a Plug and Play compatible system, without the usual
setup hassles and confusion. Your PC system can easily identify and configure itself for use with your
display. This monitor automatically telis the PC system its Extended Display Identification data (EDID)
using Display Data Channel (DDC) protocols.
69
The Windows display-settings for a typical computer are shown beiow_ However, the actual screens
on your PC will probably be different, depending upon your particular version of Windows and your
particular video card. But even if your actual screens look different, the same, basic set-up information
wiJJapply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.}
On the windows screen, select in the following
sequence : Start _ Settings _ Control Panek
When the control panel screen appears, click on
"Display" and a display dialog-box v,,'iJJappear.
Select the "Settings" tab in the display diaiogbox.
The two key variables that apply to the PDP-PC
interface are "resolution" and "colors".
The correct settings for these _'o variables are:
', Size (sometimes called "resolution'}
:640 x 480 pixeis.
', Color: "32-bit" color
Shown at left is a typical screen for "Display"
dialog box.
If a verticaJ_frequency option exists on your
display settings dialog box, the correct value is
"60" or "60 Hz". Otherwise, just dick "OK"
and exit the diaiog box.
Continued...
7O
Notes_
Both screen position and size will vary, depending on the type of PC monitor and its resolution.
The table below shows aiJ of the display modes that are supported:
Video Signal
Resolution
(DotX Line}
640 X 350
640 X 400
720 X 400
640 X 480
BM PC/ AT
Compatible
800 X 600
848 X 480
1024 X 768
Vertical
Frequency(Hz)
Horizon_l
Frequency(KHz)
Vertical
Horizontal
Polarity
Polarity
70.086
31.469
N
P
85.080
37.861
N
P
85.080
70.087
37.86!
31.469
P
P
N
N
85.039
59.940
37.927
31.469
P
N
N
N
72.809
37.861
N
N
75.000
85.061
37.500
43.269
N
N
N
N
56.250
60.317
35_156
37.897
N/P
P
N/P
P
72.188
48.077
P
P
75.000
85.061
46.875
53.674
P
P
P
P
60_000
29.838
72.000
36.072
75.000
37.650
60.004
48.363
N
N
70.069
56.476
N
N
75.029
60.023
P
P
84.997
63.677
P
P
nVidia chipset
o The interlace mode is not supported.
o The PDPoperates abnormally if a non-standard video format is selected.
', This sheet conforms to IBM/VESA regulations and is prepared on the basis of Analog Input.
', The DVI Mode is supported same as above table.
Notes:
', When this PDP is used as a PC display, 32-bit color is supported.
"
Depending on the manufacturer, your PC display screen might appear different.
(and depending on your particular version of Windows.}
Check your PC instruction book for information about connecting your PC to a PDP.
', If a vertical and horizontal frequency-select mode exists, select 6OHz (vertical} and 31.5kHZ
(horizontal}.
', In some cases, abnormal signals (such as stripes} might appear on the screen when the PC power
is turned off (or if the PC is disconnected}. If so, press the TV/VIDEO button on the remote control
or SOURCE button on the front panel to enter the VIDEO mode. Also, make sure that the PC is
connected.
o Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise,
random signals might appear}.
71
P_ese_:
Pressthe TV/VDEO button to select"PC".
Press the
MENU then
button.
Press
A orbutton.
V button to
select
"Picture",
press
the the
ENTER
Press
the _.the
or ENTER
_ button
to select "Color Control",
then press
button.
The "Color Control" is available only when
"Color Tone" is set in the custom mode.
3
Press the A or T button ta select the item you want
to change, then press the ENTER button.
Press the _l or _ button to change the value of the
item, using the on-screen gauge as your guide.
Press the MENU button to exit.
72
After connectingthe PDPte your PC,adjust the pesitiend the screenif it is net weH-dignedo
Preset:
,, Pressthe TV/VIDEO button to select "PC"
Press the MENU button. Press the ,L or _' button to
select "Setup", then press the ENTER button.
Press
the A button.
or T button to select "PC", then press
the
ENTER
Press the ENTER button to select "Position".
Adjust
the position
oJ:screen by pressing the
,L / _'/_
/ _ button.
Press the MENU button to exit.
73
P_ese_:
Pressthe TV/VDEO button to select"PC".
Press the
MENU then
button.
the ,L or
V button to
select
"Setup",
pressPress
the ENTER
button.
Press the A or T button to select "PC", then press
the ENTER button.
3
Press the A or T button to select
"Auto Adjustment", then press the ENTER button.
The message "Auto Adjustment in progress."
appears on the screen and the picture adjustments
are automaticaiJy activated.
Press the MENU button to exit.
74
Pressthe TV/VIDEO button to select "PC".
Press the
MENUthen
button.
the A or
_ button to
seiect
"Setup",
pressPress
the ENTER
button.
Press the A or T button to select "PC", then press
the ENTER button.
Press
the A the
or ENTER
T button
to select 'qmage Lock",
then press
button.
4
Press the ENTER button to select "Coarse".
Remove picture noise (vertical stripes/on the screen
by pressing the _ or _ button. (If Coarse is not set
properly, vertical stripes wiJJappear on the screen.)
Press the MENU button to exit.
75
Fine g(Fine)
Preset:
Pressthe TV/VIDEO button to select"PC".
Press the
MENU then
button.
the ,L or
V button to
select
"Setup",
pressPress
the ENTER
button.
Press the A or T button to select "PC", then press
the ENTER button.
Press
the _ the
or ENTER
_ button
to select "Image Lock",
then press
button.
4
Press the _ or _ button to select "Fine", then press
the ENTER button.
Remove picture noise on the screen by pressing
the _ or _,-button. (If Fine is not set properly, noise
wiJJ appear on the screen.)
Press the MENU button to exit.
76
P_ese_:
*
Pressthe TViVDEO button to select "PC".
Press
MENUthen
button.
,L or
_ button to
select the
"Setup",
pressPress
the the
ENTER
button.
the
Press
ENTER
the A button.
or T button to select "PC", then press
Presspress
the Athe
or ENTER
T button
to select
then
button.
The 'qnformation
vertical,
horizontal frequencies and resolution appear.
Press the MENU button to exit.
77
TI
°
Setting the Clock ..................
80
Setting the Sleep Timer ...............................................................
81
Setting the Timers ......................................................................
82
Press the
MENUthen
buttom
the A or T button to
select
"Setup",
pressPress
the ENTERbutton.
Press
the A button.
or T button to select "Time", then press
the
ENTER
Press the
the ENTER
ENTER button
button to
to select
select "Hour",
"Clock". then press
Press
the A or T button to select correct hour.
Press
A
or T
thebutton
_ button
to select
to select
correct
"Minute",
minute.then press the
Press the _ button to select "am/pro", then press the
A or T button to select the proper time of day
(am or pm!.
Pressthe MENU button to exit.
80
You can set your PDPto automatically turn off after a preset intervak
Press the
MENUthen
button.
the A or
_' button to
select
"Setup",
pressPress
the ENTER
buttom
Qukkw_yt0r_essthesle÷ptimersetting:_ustpress
tl_÷"SLEEP"
_utt0nontheremote_0ntrd.
Press the A or _ button to select "Time", then press
the ENTER button.
Presspress
the Athe
or ENTER
T button
to select "Sleep Timer",
then
button.
Press
the A stay
or Ton.button
to selectranges
the time
interval
the
PDPto
The interval
from
30 to for
180 minutes.
Press the I_ button to select "Activation", then press
the A or _' button to select "On" or "Off".
Press the MENU button to exit.
81
1'
This PDPcan be set to turn on or off automatically at specific times that you choose.
Before using the timers, you must set the PDP's clock, as described previously.
Press
MENUthen
button.
the A or
T button to
select the
"Setup",
pressPress
the ENTER
button.
Press the A or _r button to select "Time", then press
the ENTER button.
Press the
the ENTER
A or T button
buttontoto select
select"Hour",
"On Timer".
Press
then press
the A or _ button to select correct hour.
Press
A
or Tthebutton
_ button
to select
to select
correct
"Minute",
minute.then press the
Press the _ button to select "am/pro", then press the
A or T button to select the proper time of day (am
or pm}.
82
Press
press
the
A the
or _
T button
button to
to select
select "Channel",
the channel then
you want
when PDP turns on.
Press
_ button
to select
then
A or the
T button
to select
the "Volume",
volume level
youpress
wantthe
when PDP turns on.
Press the ll_ button to select 'Activation ", then press
the A or T button to select "On" or "Off".
If you
want
set Off Set
Time,
the A just
or Tasbutton
to
select
"Offto Time".
the press
"Off Time"
you
set "On Time".
0
Press the MENU button to exit.
83
Selecting a Menu Language .....................................................
86
Digital Noise Reduction ...........................................................
87
Selecting the Film Mode ...........................................................
88
Setting the Melody Sound ........................................................
89
Setting the Blue Screen .............................................................
90
Viewing Closed Captions .........................................................
91
Using the V-Chip .....................................................................
92
Press
MENUthen
button.
the ,L or T' button to
select the
"Setup",
pressPress
the ENTERbutton.
Press the ENTER button to select "Language".
Press the A "English",
or 'V button
to select
the"EspaBol".
appropriate
language:
"Franc
ais" or
Press the MENU button to exit.
86
If the broadcast signal received by your TV is weak, you can activate the Digital Noise
Reduction feature to help reduce any static and ghosting that may appear on the screen.
Press
MENUthen
button.
the A or
T button to
select the
"Setup",
pressPress
the ENTER
button.
Press the A or T button to select "Digital NR", then
press the ENTER button.
Presspress
the Athe
or ENTER
T button
to select "On" or "Off",
then
button.
Press the MENU button to exit.
87
On: AutomaticaJiy senses and processes film signals from
picture for optimum quality.
all
Off: Switches off the Film mode.
Press the
MENU then
button.
Press
A orbutton.
T button to
select
"Picture",
press
the the
ENTER
Press the A or _' button to select "Film Mode", then
press the ENTER button.
Press
the Athe
or ENTER
_ button
to select "On" or "Off",
then press
button.
Press the MENU button to exit.
', Film mode is supported in TV, VIDEO, S_VIDEO and COMPONENT
88
480i.
sources
and adjusts the
! i i!
!iiili_i _!!i_!i_il
¸iiiii;''_q
You can hear clear melody sound when the television is powered on or off.
Press
MENUthen
button.
the A or
T button to
select the
"Setup",
pressPress
the ENTER
button.
Press the A or T button to select "Miscellaneous",
then press the ENTERbutton.
the
Press
ENTER
the A button.
or T button to select "Melody",
press
Pressorthe
A or T button to change the setting.
(On
Off).
89
If no signaJ is being received or the signaJ is very weak, a bJue screen automaticaJJy repJaces
the noisy picture background_ If you wish to continue viewing the poor picture, you must set
the "BJue Screen" mode to "Off".
Press
MENUthen
button.
the A or T button to
seiect the
"Setup",
pressPress
the ENTERbutton.
Press the A or T button to seJect "MisceJJaneous",
then press the ENTER button.
Press the ENTER
A or T button.
button to seJect "BJue Screen",
Pressorthe
_ or _' button to change the setting_
(On
Off).
BlueS_reen
isd]spl_,,ed
whenthereisn0signalfrommrexternal
devk÷intheExternal
Mode,regardless
oftheBlueS_reen
S÷H]ng.
90
Your 1%/decodes and displays the closed captions that are broadcast with certain TV
shows. These captions are usually subtitles for the hearing impaired or foreign language
translations. All VCRs record the closed caption signal from television programs, so
home-recorded video tapes also provide closed captions. Most prerecorded commercial
video tapes provide closed captions as weJk Check for the closed caption symbol in
your television schedule and on the tape's packaging: IT6q.
Note: The Caption feature does not work with DVD or D1%
/ signals.
1
Press the MENU button. Press the ,L or T button to
select "Setup", then press the ENTER button
Press the A or _ button to select "Caption", then
press the ENTER button.
Press the ENTER
"Caption".
A or T button
button totoselect
turn dosed
caption
on/off, then press the ENTER button.
the
Press
ENTER
the A button.
or T button
Press the
to select
A or "Mode",
T button then
to select
press
"Text" or "Caption",
4
then press the ENTER button.
Depending on the particular broadcast, it might be
necessary to make changes to "Channel" and
"Field": Press the ,L / T/_
/ _ button to make the
changes. (Follow the same procedure as in steps
3 above.}
Press the MENU button to exit.
_te
o Different channels and fields display different information: Field 2 carries additional information that
supplements the information in Field 1. (For example, Channel 1 may have subtitles in English,
while Channel 2 has subtitles in Spanish.}
91
The V-Chip feature automatically locks out programs that are deemed inappropriate
children. The user must enter a PIN (personal ID number) before any of the V-Chip
restrictions are set up or changed.
for
Note: When the V-chip feature is activated, the PIPand auto channel program features
do not functiom
Press
MENUthen
button.
the ,L or T button to
select the
"Setup",
pressPress
the ENTERbutton.
Press the A or T button to select "V-Chip", then
press the ENTER button.
The message "Enter PIN" will appear.
Enter your 4 digit PIN number.
Note: The default PIN number of a new TV set is
"0-0-0-0".
The
"V-Chip"
screen
wiJJappear.
Press
the the
A or T
button
to select
"Change
PIN", then
press
ENTER button.
4
The Change PIN screen wiJJappean
Choose any 4 digits for your PIN and enter them_
As soon as the 4 digits are entered, the "Confirm
New PIN" screen appears_ Re-enter the same
4 digits. When the Confirm screen disappears,
your PIN has been memorized.
Press the MENU button to exit.
Not_
o if you forget the PiN, press the remote-control buttons in the following sequence, which resets the pin
to 0-0-0-0 : Power Off. ÷ Mute ÷ 8 ÷ 2 ÷ 4 ÷ Power On.
92
l0
Press
MENUthen
button.
the A or
T button to
select the
"Setup",
pressPress
the ENTER
button.
Press the A or T button to select "V-Chip", then
press the ENTER button.
The message "Enter PIN" will appear.
Enter your 4 digit PIN number.
3
The "V-Chip" screen wiJJappear. To enable the
V-Chip feature, press the ENTER button so that the
"V-Chip Lock" field is "On". (Pressing the A or T
button wiJJalternate between "On" and "Off".)
Press the MENU button to exit.
93
toSetup
qV
'
First, set up a personal identification number (PIN}, and enable the V-Chip. (See previous section.}
Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating.
Press
MENUthen
buttom
the A or _' button to
select the
"Setup",
pressPress
the ENTERbutton.
Press the A or T button to select "V-Chip", then
press the ENTER button_
The message "Enter PIN" wiJJappear. Enter your 4digit PIN number.
The
"V-Chip"
screen
wiJJappean
Press thethen
A orpress
_'
button
to select
"TV Parental
Guidelines",
the ENTER button.
The
screen
Press"TV
the Parental
A or _' Guidelines"
button to select
onewiJJappean
of the six ages
based categories:
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
94
Young children
Children 7 and over
General audience
Parental guidance
Viewers 14 and over
Mature audience
At this point, one of the TV-Ratings is selected.
Press the ENTER button. Depending on your existing
setup, a symbol
will be selected.
(Blank = UnbJocked, =
Blocked/
While "_" is selected, press the ,L or _ button to
block the category.
To select a different TV-Rating, press the ,L or T
button and then repeat the process.
Note 1: The 1MY7, TV-PG, TV-14 and TV-MA have additional options. See the next step to
change any of the following sub-ratings:
FV: Fantasy violence
D: Sexually Suggestive Dialog
L: Adult Language
S: Sexual situation
V: Violence
Note 2: The V-Chip wiJJautamaticaJiy block certain categories that are "more restrictive".
For example, if you block "TV-Y" category, then TV-Y7 will automatically be blocked.
Similarly, if you block the TV-G category, then aii the categories in the "young adult" group
will be blocked (TV-G, TV-PG, TV-14 and TV-MA/. The sub-ratings (D, L, S, V} work together
similarly. (See next section.}
6
How to set the FV, D, L, S and V sub-ratings.
First, select one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on previous
page)_
Next, while the TV-Rating is selected, repeatedly press the ENTER button.
This wiJJcycle through the available sub-ratings (FV, L, S, D or V}.
A symbol " " will be displayed for each sub-rating.
While "_" is selected, press the A T, 4, or _ button to change the sub-rating.
To select a different W-Rating, press the A or T button and then repeat the process.
Note: The V-chip wiJJautomatically block certain categories that are "More restrictive".
For example, if you Mock "L" sub-rating in TV-PG, then the "L" sub-ratings in TV-14 and TVMA wiJJautomatically be blocked.
Press
the MENU
buttonbased
to clear
screens.
(Or proceed to the next section, and set up
additional
restrictions
on all
thethe
MPAA
codes}.
', These categories consist of _'o separate groups: T\Ly and TV-Y7 (young children through age
7}, and TV-G through TV-MA (everybody else}.
The restrictions for these two groups work independently: if a household includes very young
children as well as young adults, the TV guideiines must be set up separately for each age
group. (See next step.}
95
to up
u@g
gs:
G,PG,
PG 13,
R,NC°17,
X
TheMPAA rating systemusesthe Motion PictureAssociationof America (MPAA)system,and its main application
is for movies.When the V-Chiplock is on, theTV will automaticallyblock any programs that are coded with
objectionable ratings (eitherMPAA or TV-Ratings).
Press the
MENUthen
button.
the ,,L or T' button to
select
"Setup",
pressPress
the ENTERbutton.
Press the A or T button to seiect "',,"-Chip", then
press the ENTER button.
The message "Enter PIN" will appear.
Enter your 4 digit PIN number.
The
"V-Chip"
screenwill
Pressthe
A. or '_ button
to sdect
"MPAA
Rating",appear
then pressthe
ENTERbutton.
4
The "MPAA Rating" screenwill appear
Repeatedlypressthe A or '_ button to selecta particular
MPAA category.
Pressingthe ,,L or '_ button wiJ!cycle through the MPAA
categories:
G
General audience (no restrictions}.
PG
....................
P'_en!;_!.g_!d_
_g_.e_tt_:
..................................................................................................................
R
R(Restricted.
Childrenunder 17 shouldbe accompaniedbyan adult}.
NR
Not rated.
While a particular category is selected, press the A or _ button to activate it.
A selected symbol "_" will be displayed. Press the _. or _ buttan to select "_".
Note: The V-Chip will automatically block any category that is "more restrictive". For example, if
you block the "PG-13" category, then "R', "NC-1 7" and "X" wiJJ automatically be blocked aiso.
96
to
TV
If the TV Js tuned
foJJowing
To resume
Under
message
normaJ
certain
to a restricted
wiJJ appear:
viewing,
conditions
out aJJ the channds.
tune
a
channeJ,
case,
wiJJ block
it.
The screen
wiJJ go
bJank and the
rating".
to o dJf{erent
(depending
In this
the V-Chip
"Excessive
chonneJ
on the rating
use the V-Chip
using
of the
function
the
number
buttons.
JocaJ TV programs
I the V-Chip
for an
escape":
"emergency
might
Jock
Press the MENU button. Press the ,L or T button to seJect "Setup", then press the ENTER
button.
Press the ,L or T button to seJect "V-Chip", then press the ENTER button.
Enter your PIN number, and press the _ button to temporariJy disabJe the V-Chip Lock.
97
iil_
iii
_!i
i-_
ii_iii _!i
..................................
Troubleshooting ..........................................................................
Care and Maintenance ..............................................................
1O0
101
Specifications ............................................................................
102
Before you caJi a service technician
time and money.
please scan this list of problems and possible solutions. It may save you
P0ssibJe
Sdut[on
Check aJJwire connections.
hess the "MODE" button Toput your remaYecontrol in the "TV'
mode.
Cl_eck if the power plug is connected.
€.3heckto see that both the PDPand the source are plugged in
and turned on.
Adlust the Bric htness or Contrast setting s,
Adjust the Size settings.
100
With proper care, your PDPwiJJgive you many years of service. Please follow these guidelines to get
the maximum performance from your PDP.
JdentiJyingPr0bJems
o Do not put the PDP near extremely hot, cold, humid or dusty places.
Do not put the PDP near appliances that create magnetic fields.
Keep the ventilation openings dean
Do not place the PDP on a rough and slanted surface, such as cloth or paper.
Liquids
Do not place liquids near or on the PDR
Cabinet
Never open the cabinet or touch the parts inside.
Wipe your PDP with a dean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.
Do not put heavy objects on top of the cabinet.
Temperature
,
If },our PDP is suddenly moved from a cold to a warm place, unplug the power cord for at least _o
hours so that moisture that may have formed inside the unit can dry completely.
101
Exterior design and product specifications are subject to change without prior notice to improve
the performance of this product.
This PDPoperates as a Class B digital device.
(Note: Class B system is for home use.}
This PDP has been registered for residential use with regards to EMk
MZ42S4
SPP4251
1050 (W/ X 86 (D)X 755 (H) mm
59 (W} X 22 (DIX 209 (H)mm
36kg ; 791bs
164g ; 0.361bs(includingbatteries)
120V_, 60HE
330W
852(H)x 4801V)
107 Cm/42 inches
VHF,UHF(75£2unbalanced)
AV1
AV2
A\,"3(SIDE}
SVIDEO 1
S:v'IDEO2 (SIDE}
COMPONENT1-480i/48%
/ 72% / 1080i
COMPONENT2- 480i / 48% / 72% / 1080i
RGB: PCDSUB15P
DV_
AV1
AV2/S-VIDEO I
AV3 (SIDE}/ S-VIDEO2 (SIDE}
COMPONENTl-480_/48%
/ 72% / 1080i
COMPONENT2-480i/48%
/ 72% / 1080i
PC
DV_
VIDEO,AUDIO(L/R}
15W+15W (8 [2)-Internal Speaker
102
! i
IU
dl;
¸ ,,
103
104
105
1-800-SAMSUNG
(1-809-726-7864)
Samsung Electronics
Service Division
America
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
www_samsungusa_conl
Samsung Electronics Canada
Samsung Customer
Care
7037 Financial Drive
Mississauga,
L5N 6R3
Inc.
Ontario
www.samsung.ca
BN68=00618A-01
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 99 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Apr 03 17:22:53 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools