SDC Visio INST 90 DEG FS23M Bolt Lock Installation Instructions Installs

User Manual: SDC FS23M Bolt Lock Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 2

INSTALLATION INSTRUCTIONS

FS23M, 1090, 1190 SERIES

OVERHEAD INSTALLATION HORIZONTAL

1. Examine the top rail of the door for the most suitable location for the strike. Mark the door for the end of the strike closet to

the lock stile, and make a corresponding mark on the header to line up with the first mark.

2. Locate center line of door thickness on the header and attach adhesive cut out template to header. Lining it up with marks,

center punch the tab-mounting screw locations and counter-sink for #10 screw. Saw or rout out the cutout area.

SIDEJAMB INSTALLATION VERTICAL

3. Examine the lock stile jamb for the point nearest the center of the door height, with space available for the lock and strike.

Mark the door stile horizontal for the top end of the strike and make a corresponding mark on the jamb.

4. Locate center line of door thickness on the jamb and attach adhesive cutout template to jamb, lining up the the top of the

cutout with the horizontal mark on the jamb. Center punch the tab mounting screw locations and counter sink for #10 screw.

Saw or rout the cutout 1-1/2” x 8”.

5. Attach the mounting tabs inside.

6. (FS23M only) bore 5/16” hole for pilot lamp on inside face of frame as shown.

7. Attach power supply leads to lock leads as shown. Handle the lock carefully; do not hang it by the wire leads. Insert wires

into the header cavity carefully so they do not interfere with proper locating of the lock in the cutout.

8. Insert lock. Horizontally, the bolt end is nearest the lock stile. Vertically, the bolt must be at the top end of the cutout. Secure

with 10/32 machine screw.

9. Using strike for a template, mark screw hole location and drill holes for screws supplied. Mortise as required. Attach strike.

10. The automatic relock switch is set for 1/8” clearance between the top of the door and transom bar or head jamb. Any

additional gap may be compensated for by loosening the lock nut and turning the switch assembly clockwise until proper

adjustment is reached. Be sure to tighten lock nut when adjustment is satisfactory.

1. Mortise cutout in

tube for face plate

(fits flush with

surface of tube).

2. Position screws

for attaching

tabs, drill holes,

attach tabs.

4. Slide lock into

position, attach

to tabs.

3. Connect wiring

to lock.

P:\INSTALLATION INST\Electric Bolt Locks\INST-90 DEG Dual Coil\INST-90 DEG.vsd REV E 06-13 Page 1

Easy Installation or Servicing

All Space Saver locks are

easily installed in any existing

entrance merely by mortising

out a cutout, attaching the

wiring, inserting the lock, and

bolting it into position with two

attaching tabs. Cutting studs is

no longer a problem or

expense.

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

Fig. 2

Auto Relock Switch

Adjustable for Wide Door Gap

Loosen nut.

Turn assembly

clockwise for wide

door gap.

Tighten nut.

Fig. 1

801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •

www.sdcsecurity.com • E-mail: service@sdcsecurity.com

P:\INSTALLATION INST\Electric Bolt Locks\INST-90 DEG Dual Coil\INST-90 DEG.vsd REV E 06-13 Page 2

1190A

Face plate: 8” x 1-1/2” x 0.125”

(203.2mm x 38.1mm x 3.175mm)

I.D. Requirements: 8” x 1-1/2” x 1-1/2”

(203.2mm x 38.1mm x 38.1mm)

Solenoid: Continuous duty

Standard voltage: 24VDC @ .7 Amp

Strike: M-Mortise 4” x 1-1/2” x 0.125” (101.6mm x 38.1mm x 3.175mm)

Bolt: 3/4” (6.35mm) dia. S.S., 3/4” (6.35mm) throw

1091A/1091ADL (DEADLOCKING)

Face plate: 8” x 1-1/2” 0.125” (35.1mm x 35.1mm x 3.175mm)

1091STA: 4-7/8” x 1-1/4” x 0.0937” ANSI

(123.53mm x 31.75mm x 2.28mm)

I.D. Req. 8” x 1-1/2” x 1-1/2”

(203.2mm x 38.1mm x 38.1mm)

Solenoid: Continuous duty

Dual Voltage:

12VDC @ .9 AMP

24VDC @ .45 AMP

Strike: M-Mortise 4” x 1-1/2” x 0.125” (101.6mm x 38.1mm x 44.45mm)

Bolt: 5/8” (15.88mm) dia. S.S., 3/4” (6.35mm) throw

FOR FS23M AND 1091A/1091ADC:FS23M

Face plate: 8” x 1-1/2” x 1/8”

(203.2mm x 38.1mm x 3.175mm)

I.D. Requirements: 8” x 1-1/2” x 1-1/2”

(203.2mm x 38.1mm x 38.1mm)

Solenoid: Continuous duty

Dual Voltage:

12VDC@ .9 Amp

24VDC@ .45 Amp

Strike: M-Mortise 4” x 1-1/2” x 0.125” (101.6mm x 38.1mm x 3.175mm)

For wood 1-3/4” deep (44.45mm)

Bolt: 5/8” (15.88mm) dia. nylon with magnet insert, 5/8” (15.88mm)

throw.

Red pilot lamp standard to indicate door locked.

FOR 1190A ONLY:

DOOR IS SHOWN CLOSED AND LOCKED.

UNLOCKING MAY BE CONTROLLED BY

MULTIPLE SWITCH LOCATIONS.

RED

POWER

N.C.

ACCESS CONTROLS

N.O.

A.R.S.

YELYELWHT

N.C.

TROUBLE SHOOTING

Problem Solution

Bolt does not project Check voltage and alignment

of strike.

Bolt projects but chatters Voltage too low.

Bolt will not retract Strike misaligned

BOLT POSITION SENSOR (MAGNETIC)

B Indicates bolt locked or unlocked .25 Amp

DOOR POSITION SWITCH (MECHANICAL)

D Indicates door opened or closed 5 Amp

ARS

YEL

YEL

12 VDC CONFIGURATION

RED

BLK

BLU

WHT

YEL

YEL

RED

BLK

BLU

WHT

24 V CONFIGURATION

RED = N/C

WHT = COM

BLU = N/O

CONTACT RATING

5 AMPS @ 125 VAC

RED = N/C

WHT = COM

BLU = N/O

DPS

DPS / BPS CONFIGURATION

BPS