SDC Visio INST E600 Magnetic Lock Installation Instructions

E600 INST-E600

User Manual: SDC E600 Magnetic Lock Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 4

801 Avenida Acaso, Camarillo, Ca. 93012

(805) 494-0622 • Fax: (805) 494-8861

www.sdcsecurity.com • E-mail: service@sdcsecurity.com

The E600 Series magnetic lock is mounted to the underside of the header, on the stop side of the

door. An inswing mounting kit (optional) can be used when mounting on the hinge side of the

door.

P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A 07-10 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

INSTALLATION INSTRUCTIONS

E600 SERIES MAGNETIC LOCK

Outswing

Electrical Instructions:

Use properly fused U. L. Listed Power Supply

Do not install a diode in parallel with any magnetic lock. A diode

will cause a delay when releasing the door and residual magnetism

to occur.

Although SDC recommends the use of a DC power supply, a

transformer with an adjacent mounted full wave bridge rectifier

may be used. A significant drop will occur when using a full wave

bridge rectifier.

Any low voltage condition will cause erratic operation of the

optional board sensor.

When using a full wave bridge rectifier all access controls and/or

release contacts must be located between the magnetic lock and rectifier

to ensure quick release.

Electrical Specifications:

Dual Voltage 12 or 24VDC

Power Consumption 500mA@12VDC

250mA@24VDC

DS Door Status Sensor SPDT, 500mA@30VDC

LS Lock Status Sensor SPDT, 2A@30VDC

Quick Mount

Interlocking

Mounting Assembly

Mounting Screws

Armature

Interlocking

Mounting Plate

Frame

P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A 07-10 Page 2

1. Inspect the frame header to determine if mounting accessories are required (refer to page 4).

2. Fold template as indicated on dotted line. For single doors locate template against the door and header on the

lock jamb side of the frame.

3. Mark and drill holes as indicated by the template.

4. Mount armature to door.

STEP 4

STEPS 2 & 3

STEP 5

5. Install mounting plate to header with the interlock detail away from the door side of the stop.

Loosely fasten screws through adjustment slot as shown. Assure that the mounting plate and

armature line up properly, then tighten down ALL mounting screws.

P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A 07-10 Page 3

7. Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock.

STEP 6

A/C

MAINS

POWER

SUPPLY

12VDC

or

24VDC

+

-

SWITCH or ACCESS CONTROL

8. Test operation. When all is operating properly, tighten

all screws as shown. Install anti-tamper plugs over socket head

screws using a soft hammer to avoid damage to the housing.

6. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the

door. Tap with a soft hammer to ensure proper alignment and engagement.

CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head

screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the

threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing

COM NC

NO

Door Position Sensor (Reed switch)

RED (open with door closed)

GREEN (closed with door closed)

BLACK

+ -

NO C NC

1 2 3 4 5

Power

Supply Lock Status

Switch

Voltage Jumper 12VDC

24VDC

A RED LED INDICATES

ENERGIZED & UNSECURED

(GREEN=ENERGIZED & SECURE)

LED

P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A 07-10 Page 4

To maintain surface plating from corrosion:

Do not touch the lock face with your hands.

Clean lock face with Scotch-Brite pad by 3M (do not use sandpaper).

Apply a thin film of rust inhibitor (LPS-3) on lock face.

Repeat application on armature plate.

Supplied Mounting Hardware

ANGLE BRACKET

E12L

Inches: 10.5" L x 0.5" H x 0.75" D

mm: 266 L x 12.7 H x 19 D

May be field cut for use with E600

ADJUSTABLE ANGLE BRACKET

E6A

For use with Model E600 Series

STOP FILLER PLATE

EF02

Inches: 10.5" L x 0.5" H x 0.75" D

mm: 266 L x 12.7 H x 19 D

May be field cut for use with E600

GLASS DOOR ARMATURE BRACKET

E6U

For use with Model E600 Series

Field adjustable for glass thickness

TOP JAMB MOUNTING BRACKET

E6Z

For use with Model E600 Series

MOUNTING ACCESSORIES: