SDI Technologies IBT73 GlowTunes Bluetooth Rechargeable Mini Speaker User Manual iBT73 IB EN 526

SDI Technologies Inc. GlowTunes Bluetooth Rechargeable Mini Speaker iBT73 IB EN 526

User Manual

For Models That Use Lithium Batteries• Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire, or high temperatures & not handled appropriately• Do not place loose batteries in a pocket, purse, or other container containing metal objects, do not mix with used or other battery types, or store with hazard-ous or combustible materials. • Store in cool, dry, ventilated area. • Follow applicable laws and regulations for transport and disposal.A Consumer Guide to Product SafetyIMPORTANT SAFETY INSTRUCTIONSWhen used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit.1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. 2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through the ventilation openings.3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket.6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning instructions.7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product.8. Attachments – Do not use attachments not recommended by the product manufacturer.9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges.10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.11. Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. the power supply cable or plug has been damaged. B. objects have fallen into or liquid has been spilled into the enclosure. C. the unit has been exposed to rain. D. the unit has been dropped or the enclosure damaged. E. the unit exhibits a marked change in performance or does not operate normally.12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power cable should be unplugged from the unit to prevent damage or corrosion.13. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.Maintenance• Place the unit on a level surface away from sources of direct sunlight or excessive heat.• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture.• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents such as thinner or similar materials can damage the surface of the unit.Limited 1 Year Warranty InformationiHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of one (1) year from the date of original purchase.Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI will repair or, at its discretion, replace this product without charge. This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center authorized by SDI Customer Service. The product must include proof of purchase, including date of purchase. An out-of-warranty fee for service will be charged for units that are received without proof of purchase.Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries are the most common cause of problems encountered.If service is still required:1. Call SDI Customer Service at 1-800-288-2792 for Return Authorization and for the address of the Factory Service Center. 2. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box SDI is not responsible for damage that occurs during shipping to the Factory Service Center.3. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period. Also include your name and address information, a brief description for why the unit is being returned, and the return authorization number. No unit can be processed without a return authorization number.4. Write the return authorization number on the side of the shipping package and send the unit prepaid and insured to the Factory Service Center address authorized by SDI Customer Service.Disclaimer of WarrantyNOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser. In no event will SDI or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI product.© 2014 SDI Technologies, Inc. All rights reservedQuestions? Visit www.ihome.com or call 1-800-288-2792 Toll FreeiBT73-140526-A Printed in ChinaFCC ID: EMOIBT73IC: 986B-IBT73Model: iBT73 (Front)IB (English) Size: 324Wmm x 200HmmColor: Print in Black colorDate: May 26, 2014Questions? Visit www.ihome.comFCC InformationFCC Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.• Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.CAN ICES-3 (B)/NMB-3(B)QDID: B020770IMPORTANTRead before proceedingIf you have any question regarding the operation or use of this product, please visit www.ihome.com to view answers to frequently asked questions.To learn more about this and other iHome products, please visit us online at www.ihome.comModel iBT73GlowTunes Bluetooth RechargeableMini SpeakerCHARGEBEFOREUSEBluetooth ModeAux-in ModeModel: iBT73 (Back)IB (English) Size: 324Wmm x 184HmmColor: Print in Black colorDate: May 26, 2014Audio/Charging Jackto playto playto pair, then playOff/On/Bluetooth SwitchCharging/PairingLEDSpeaker front viewSpeaker left viewSpeaker back viewSpeaker right viewLocking and Unlocking the iBT73To compress and lock speaker, gently press speaker down from the top and twist clockwise to lock in place.To unlock and expand the speaker, grip the top and bottom and give a small twist counter-clockwise. DO NOT pull hard once open, as the built in spring will automatically extend the speaker to its proper position.Charging the iBT73The iBT73 is powered by a rechargeable battery in the speaker. Make sure to charge speaker before use.• Connect the micro-USB plug to the Audio/Charging jack on the speaker.• Connect the larger USB plug to a powered USB port, such as that on a computer. Your computer should be connected to a wall outlet when speaker is charging. The light on the speaker will turn to solid red while charging and turn off when fully charged.• If the blue LED dims, or you notice sound distortion at higher volumes, or there is no sound at all it's time to recharge the batteries. Note: the LED Lighting Effects may still work even in low battery conditions. Using Bluetooth with the iBT73• Slide the of Off/On/Bluetooth Switch on the speaker to the Bluetooth position ( ). The light will flash blue and red and a tone will sound as the speaker attempts to pair with a Bluetooth device. • Place your audio device in Bluetooth mode (often found in the device’s Settings or Tools menu) and make it “discoverable”. “iHome iBT73” should appear on your device. If “Not Connected” or similar message appears, select it to connect. If your device asks for a passcode, enter ‘1234’.• Once paired, the light will glow solid blue. You can then stream audio to the speaker. If pairing is not successful, turn the power OFF ( ) on the speaker and repeat pairing procedure.• To listen to Bluetooth audio, make sure the Off/On/Bluetooth Switch on the speaker is in Bluetooth ( ) or ON ( ) position. • Control Bluetooth audio from your device. Remember to turn off the speaker and your device after listening. NOTE: When unit is charging, the blue light will appear solid red.Using the iBT73 with Aux Devices• Connect the micro-USB plug to the Audio/Charging jack on the speaker.• Connect the stereo 3.5mm audio plug to the headphone jack or line-out of any audio device.• Slide the Off/On/Bluetooth Switch on the speaker to the ON ( ) position. The blue power light will flash, indicating auto-link mode. • Press play on your audio device and adjust its volume to listen to audio.iHomeLED LightingEffects ButtonWhen speaker is ON ( ), press the LED Lighting Effects Button to cycle through 4 lighting effects modes: Fast Color Cycle, Slow Color Cycle, One Color, and lighting effect Off.Micro USB plug3.5mm audio plugStandardUSB plugCombination cableMobile Phone Game Devices iPod LaptopPC/Tablet MP3/MP4Charging the iBT73CHARGE BEFORE USEComputer USB portUSB AC adaptor(not included)USB AC adaptor connected to working outletComputer connected to working outlet

Navigation menu