SEGI ANB300-2WLS Keyless Entry System User Manual
SEGI LIMITED Keyless Entry System Users Manual
SEGI >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2657892 |
| Application ID | S4nqbbYKPavfXT6Yy3r0vw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 29.29kB (366095 bits) |
| Date Submitted | 2015-06-25 00:00:00 |
| Date Available | 2015-06-25 00:00:00 |
| Creation Date | 2015-06-25 17:05:28 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2015-06-25 17:05:28 |
| Document Title | Microsoft Word - VA5ANB300-2WLS(7087A-2WANB300LS) User Manual(KEY_EN)_안테나í¬í•¨.docx |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | choo |
2-WAY REMOTE STARTING SYSTEM WITH 1 BUTTONS FOR AUTOMATIC TRANSMISSION RED301-2WAY / ANT-2WDSS User Guide For Key This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. WARNING It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner. 1. When leaving the vehicle, it is the user’s responsibility to ensure that the gearshift lever is in “Park” in order to avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot start in “Drive”.) 2. It is the user’s responsibility to ensure that the remote starter is disabled or put into valet mode before servicing. FCC COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and Using the remote control (2) This device must accept any interference received, including interference that may cause undesired operation. Description of Remote Appearance CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. AVERTISSEMENT Il est de la responsabilité du conducteur de s’assurer que son véhicule est stationné de façon sécuritaire et responsable. 1. En quittant le véhicule, le conducteur doit s’assurer que le levier de boite est à la position P (stationnement) afin d'éviter tout accident lord d'un démarrage à distance. (Note : Assurez-vous que le véhicule ne peut pas démarrer alors que le levier de boite est à la position D (Drive). 2. Il est de la responsabilité du conducteur de s’assurer que le démarrage à distance est désactivé ou que la télécommande est en mode Valet lorsque son véhicule est au service mécanique. CONFORMITÉ FCC Ce dispositif est conforme à l’article 15 de la réglementation du FCC. Le fonctionnement est assujetti aux deux conditions suivantes : (1) Ce dispositif ne causera pas d’interférences dommageables, et (2) Ce dispositif doit pouvoir être soumis à toute interférence, y compris des interférences pouvant causer son mauvais fonctionnement. ATTENTION : Des changements ou modifications non approuvés expressément par la partie responsable de la conformité pourraient faire en sorte qu’il soit interdit par l’utilisateur d’utiliser ce dispositif. Usingg the remotee control Descripption of Remotte Appearance Lock, Unlock and a Remote Lock, Unlocck and Remote Starting icon is s displaying with Starting icon n is displaying with One LED color. Two LED co olor. Loc ck/Unlock Note: Press the button 1 time on the rem mote control transmittter to lock the veh hicle. Press the butto on 2 times to START/STOP: unlock the driver’s door, 2 additional Note : Remo ote Engine Start - tim mes to unlock all doorrs. Press the buttton 1 time and then, within 3 seco onds, press and hold the button forr 2 seconds 2Way Remote Remote Eng gine Stop - Press the button forr 2 seconds Button F Functions Bu utton Pre ess buttons for LED Function Press 1time Lock Press 2 times Unlo ock driver’s door Pre ess 2times x 2 Unlock all doors 2 seconds Re emote start/stop Note: Yo ou make sure presss button only afte er LED lighting ends to activate eacch feature properly y. 1Way y Remote Vehicle Presets Heater When leaving the vehicle it is recommended to preset the accessory controls in preparation for the Next remote start. Settings for the blower motor(fan),front and rear (if equipped),should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM instead. Windshield Wipers, Headlights Certain vehicles require the windshield wipers and headlights circuits to become energized while running under remote start. When leaving the vehicle you must ensure that the windshield wipers and headlights switches are OFF. Leaving the headlights switch ON on certain types of vehicles could cause them to remain ON even after remote starter shutdown, resulting in a dead battery. Leave Windshield Wipers off to avoid damage wipers/motor with remote start. Changing the Remote Control Transmitter Battery Remote transmitter should be provided with two 3-volt lithium battery (Model: CR-2025). Please pay attention that with low battery LED in the remote might not work and the remote start distance might get shorter. Batteries can be purchased at any electronic device stores. Following the instructions below to change the remote control battery 1. You may use a coin to pry the remote control halves apart 2. Remove the old battery and replace with a new one 3. Be sure to observe the (+) sign when inserting the new battery. 4. Before assembling transmitter case, you should test the remote control. Note: LED D icon of 2way tra ansmitter indicates s firstly blue colorr and then change e to “RED” color when you press an ny button. In this case, it’s time to change CR2025 ba attery ne ewly Descripption of Antennna Appearance 2Way Antenna Antenna Harness Note: Usse the power of the e antenna car batttery 12volts. Remote-Starting your Ve ehicle Remote-Starting For the 2 2-way remote: 1. Press tthe butto on one time. The remote will beep o once and display tthe Lock icon. The en, press the button within 2 seconds. The remote will beep once and display th he KEY icon. 2. 5 seco onds later, the rem mote will activate starter. The Key iccon will be shown with 3 different tones of beeping th hen the LED Icon will w be scrolled.. For the 1 1-way remote: 1. Press button one time and Lock LE ED will be displaye ed. Then press button for 2 se econds within 3 se econds. utton for 2 seconds. 2. Remotte Stop - Press bu If your ve ehicle does not sta art at the first attem mpt, the system w will shut down, wa ait a few seconds and a try to start the e engine again. Th here will be 3 starrt attempts before the system gives up. Note: Ple ease make sure prress to button only y after LED lightin ng ends to activate e each feature pro operly. Off (Steps from R Remote Start to Driving) Driving O With the vvehicle running re emotely, press es to disarm the O OEM Starter Kill an nd/or the OEM ala arm and unlock th he doors. Enter the e vehicle and do the button 2 time following:: 1. Turn th he ignition key to tthe IGNITION ON N (RUN) position. (Do not tu urn the key to the CRANK position while the engine is running. This w would cause the sttarter motor to ree engage. Disarm th he remote starter mode by pressing g the foot brake) 2. Press tthe brake pedal to o disengage the re emote starter unitt. With the vehicle e key is in the IGNITION ON positio on, press the brake e pedal or wait 30 0 seconds for the vehicle to turn to ready status to drive e. Note: In rremote engine sta art status, engine will w be deactivated according to following conditions. - Open th he door and 30 se econds is passed. - Press brake pedal withou ut key is in IGNITION ON position. Engine Run Time Your Re emote Car Starte er can be program mmed to run the engine for 10 orr 5 minutes (10 minutes by defau ult). Note : R Run time is set by installer. To chec ck the amount off runtime remainiing (2-way only):: After prressing button once, if you u press buttton 2 times with hin 3 seconds, re emote starter will be operated. Once remote starrter is succeeded d and the engine is turned on, the remote will receive signal an nd shows the rem maining remote starter time as a START LED icon n. Remote S Starter Features Remote S Start Error Diagn nostic If remote engine starter fails, the vehicle will not be started an nd the horn will so ound accordingly to t the table below w. Number o of Horn times Remote Start Error Hood open KEY IN or IG1 ON Valet mode Brake pres ss Trunk open Door open Valet/Serrvice Mode For REM MOTE Start KEY F Fob Valet/Serrvice mode is used d to prevent the system from unexp pectedly starting tthe engine while being serviced. When you ur vehicle is in Va alet Mode, the rem mote starter functio onalities are disab bled. If the vehicle e needs to be serv viced, or if you park it indoors, the Valet Mode will pre event the engine fro om being remote--started accidenta ally. Any of the e following feature es will put your re emote car starter into Valet Mode : Remote V Valet: This feature allow ws you to put yourr system into Valett Mode by using the transmitter. To Engag ge Valet Mode/Serrvice Mode: (Apprroaching to Functtion stop mode) 1) Insert tthe vehicle’s key tto the IGNITION, turn to the ON po osition. 2) Press and hold the vehicle brake. 3) Press and hold the remo ote button fo or 2 seconds, the key LED will flash h and the vehicle’s s indicator will flas sh 1 time. Valet mode is engaged. To take th he system out of V Valet Mode (Returrn the system to itts normal operatin ng mode): (Disarm ming “Function Sto op Mode”) 1) Insert tthe vehicle’s key tto the IGNITION, turn to the ON po osition. 2) Press and hold the vehicle brake. 3) Press and hold the remo ote button fo or 2 seconds, the key LED will flash h and the vehicle’s s indicator will flas sh 2 times, Valet mode is cancelled d. y whether the sys stem is in Valet Mode using the 2 2-way remote: To verify If system is in Valet mode, buzzer sounds shortly when lock o or unlock button iss pressed. ed Features: Installation-program mmable Options Advance The Rem mote Car Starter w was designed with flexibility and OEM integration in m mind. With its prog grammable options, this unit can virrtually control nea arly any electrical system in your vehicle. Caution: The programming of your system should be left to a professional. Changing any one of the settings may affect the operation of your Remote Car Starter. Engine Run Time setting Option Setting Condition Disarm the vehicle with remote control transmitter.(Unlock) Driver s door must be physically Open, Engine Stop, Ignition ON, Trunk Open and Hood Open. Option Setting Instruction - Under option setting condition, press button for 2 seconds. Light and Horn of vehicle will activate according to Engine Run Time option. Number of Indicator+ Horn Settings 1 Time 10 Mins (Default) 2 Times 5 Mins Light Blinking during remote engine start Option Setting Condition Disarm the vehicle with remote control transmitter.(Unlock) Driver s door must be physically Open, Engine Stop, Ignition ON, Trunk Open and Hood Open. Option Setting Instruction - Under option setting condition, press button for 2 seconds. Light and Horn of vehicle will activate according to Light Blinking during remote engine start. Number of Indicator+ Horn Status 1 Time Blink OFF (Default) 2 Times Blick ON Pairing Remote Start Fob The Remote Start Fobs in Remote Start Kit are already paired with the main module at the time of production. There is no need to pair the Fobs at the time of the first installation. 1. When a new registration is needed - When replacing a remote due to loss or malfunction of a remote. - When re eplacing the main controller installe ed in the vehicle. - When a adding or changing g the remote upon n user’s need. 2. Pairing g procedure RS Fob X1 5X 1) Open d driver’s door and trunk. 2) Insert tthe key into the ig gnition. Turn the key from OFF to O ON position 5 times within 5 seconds. 3) After step 2), within 5 se econds, Press buttton on the 1st Re emote Start Fob 1 time. 4) After re egistering the 1st Remote Start Fob b, within another 5 seconds, Press button on the nex xt 2nd Remote Sta art Fob 1 time. 5) Verify tthat all Fobs are ffunctioning correc ctly by performing Lock / Unlock fun nction. NOTE: 1) A syste em can recognize e up to 3 remotes maximum. 2) If a new w Fob, or addition nal Fob, is needed d later, the Fob pa airing process sho ould be done with the original Fob or o oldest available e Fob. shooting Poor Trransmitting Rang ge Troubles Many facctors may affect th he operating range e of the transmitte er. Some of these are: -The condition of the batteries in the transmitter. -The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers, etc). -Metal in the area of the vehicle of transmitter. This includes the vehicle itself. -The shape of the vehicle can affect range as well. Vans in general have greater interference. The shape of the roof and A-pillars causes considerable radio-frequency interference. Demonstrate to users that the best range is facing the vehicle's front. The worst range is facing the vehicles right or left side. Please inform the users that facing the vehicle’s front offers the best range. The worst range is experienced facing the R or L side. -The amount of other vehicles in the area of the target vehicle. -The method of using the transmitter. Always hold the transmitter high, approximately at shoulder height. Automatic Engine Start Repeat Remote Start is programmed to repeat the engine start sequence two (2) more times after ten (10) seconds if the engine start fails because of low vehicle battery.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : choo Create Date : 2015:06:25 17:05:28+09:00 Modify Date : 2015:06:25 17:05:28+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : choo Title : Microsoft Word - VA5ANB300-2WLS(7087A-2WANB300LS) User Manual(KEY_EN)_안테나포함.docx Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:174d1492-1eac-47f4-9936-0532884e4130 Instance ID : uuid:d65f98d7-cb4f-4f0d-80e9-a8a6d15c3a76 Page Count : 11EXIF Metadata provided by EXIF.tools