SENA TECHNOLOGIES SP40 Wireless Interface Module User Manual Bluetooth Wireless Serial Adapter

Sena Technologies,Inc. Wireless Interface Module Bluetooth Wireless Serial Adapter

User Manual

Wireless Interface Module W.I.M (Wireless Interface Module) User Manual FCC ID: S7A-SP40
Wireless Interface Module WIM Introduction 1.01.1 Background The Wireless Interface Module (WIM) is a Bluetooth enabled electronic control unit designed for use with Harley Davidson touring motorcycles. The WIM will interface with both Premium and Standard infotainment units and replaces the wired headset. The WIM is not compatible with Harley’s Cruiser, Sportster, or Street lines. The WIM will be sold in any market touring motorcycles are sold. Figure 1: WIM System Block Diagram 1.2 Basic Operation and Block Diagram ISYS RADIORear Wired Headset 435621E1 Rear Headset, Left +E2 Rear Headset, Right +E3 Headset Common -D1 Rear Microphone +C2 Microphone Common -D2 Microphone ShieldFront Wired Headset 435621F1 Front Headset, Left +F2 Front Headset, Right +C1 Front Microphone +A3 Accessory CAN-A4 Accessory CAN+Wireless Interface Module Front Headset, Right +Microphone Common -Front Headset, Left +Headset Common -Rear Microphone +Front Microphone +CAN-CAN+P&A Relay PowerGroundRear Headset, Left +Rear Headset, Right +P&A Relay Figure 2: Basic WIM System Block Diagram
Wireless Interface Module 1.3 DUT Orientation Orientation A Orientation B Orientation C Table 1: DUT Orientations 1.4 Connector and Pin-Out Figure 3: WIM Pin Diagram
Wireless Interface Module Pin Signal 16 Rear Headset Left 15 Rear Headset Right 14 Headset Common GND 13 Front Headset Left 12 Front Headset Right 11 USB GND 10 Rear Microphone 9 Front Microphone 8 Microphone Common GND 7 USB Power (5V) 6 CAN Plus 5 CAN Minus 4 USB Data Plus 3 USB Data Minus 2 POWER GND 1 POWER Input Table 2: WIM Connector Pin Table
Wireless Interface Module FCC Part 15 Subpart C Section 15.247 FCC ID: S7A-SP40 FCC Compliance Statement FCC Part 15.19 Statements: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesiredoperation. FCC Part 15.21 statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.IC RSS-GEN, Sec. 7.1.3 – (licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. CE Hereby, SENA TECHNOLOGIES.Inc Declares that this SP40 is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. This equipment should be installed and operated with minimum 20 cm between the radiator and your body.

Navigation menu