SES imagotag APG2-USB1-A digital network controller device User Manual

SES-imagotag GmbH digital network controller device

User Manual

Document Title Goes HerePage 11. 2. 3. a. Test setup and specification for certification testsDescriptionThis page describes the quick-start with a per-defined test setup and how-to run tests with this setup.FCC: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interferencethat may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could voidthe authority to operate the equipment.IC: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may causeundesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation estautoriséeaux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillageradioélectrique subi,même si le brouillage est susceptible d’en compromettre le fonctionnement.Pr-requisitesNetwork cableLocal machine (laptop/PC)Ethernet interfaceAdministration rights (to change the network settings)JAVA Runtime Environment ( ), Version 8 or higherJRETest setup componentsCore appliance 32GB - ID 52675 - 05CAB002303-I200000720ESL Dongle - ID 50400AP-2010 - ID TBAUSB pen drive incl. " " softwareControl CenterInitial test setup preparationPrepare local machineChange your Ethernet adapter settingsControl Panel - Network ConnectionsRight click on the desired Ethernet interface and select " "Properties
Document Title Goes HerePage 23. a. 4. 5. a. b. c. 1. a. b. Select " " and click " "Internet Protocol Version 4 (TCP/IPv4) PropertiesUse the following IP address and subnet maskIP address: 192.168.1.30Subnet mask: 255.255.255.0Prepare core appliance, ESL dongle and/or AP-2010Unpack componentsUnpack core appliance, power supply and ESL dongle.
Document Title Goes HerePage 31. b. 2. a. b. c. d. Connect componentsNetwork cable Ethernet port " " & Ethernet port of your laptop or PC1Power jack Power socket " "DC+12VESL Dongle USB port " "1
Document Title Goes HerePage 42. d. 3. 4. a. b. c. d. Power core appliance Power switch " "ONCopy the following folder from the USB pen drive to your local computer: " "Control_CenterExample local directory: " "C:\ses-imagotag\Make sure that JAVA is installed on your local machine. (e.g.: Open a windows command prompt and execute "java" command)-version
Document Title Goes HerePage 54. d. 5. a. 6. 7. 8. a. Create shortcut with " "client.jarRename shortcut to " "Control Center - 192.168.1.10Edit shortcut with right click " "PropertiesAdd " " after " " as target link and apply the changes --host 192.168.1.10 client.jar
Document Title Goes HerePage 68. a. 9. a. 10. a. b. 11. a. Rename the shortcut to " "client.jar - 192.168.1.10Execute the shortcut and use the following username/password combination to login:Username: adminPassword: adminWait until the "Control Center" window opens
Document Title Goes HerePage 711. a. 1. 2. a. Working with labelsYou'll find information about working with labels in the " "Core Service Quick Start Guide10.1 Register labels11.2 Sending images to labelsSources:https://portal.imagotag.com/get/documentationhttps://portal.imagotag.com/files/all/docs/it_quick-start-guide_en.pdfOperate the system with an AP-2010This section describes how to change the operation from an ESL dongle to an AP-2010.Unplug the ESL dongleDelete the configuration of AP-ID "50400" via Control Center: " "System Access Point ConfigurationYour system's now ready to start working with labels (register, send images, switch pages, ...)Your current ESL channel is 10 (ESL dongle LED is blue)Example imagesThe USB stick contains a collection of test images that can be sent to the labels.
Document Title Goes HerePage 82. a. 3. a. b. 4. 5. 6. a. Connect the Ethernet interface of the AP-2010 with the of the core applianceEthernet port 2Use the included network cablePlug in the power supply of the access pointWait until the AP-2010's LED turns blueCheck the Access Point status via Control Center: " "System Access Point Status
Document Title Goes HerePage 96. a. 1. a. b. c. 2. a. b. c. d. e. 3. 4. 5. a. Change back to the operation with ESL dongleThis section describes how to change the operation from an AP-2010 to an ESL dongleSwitch off the AP-2010http://192.168.1.20/admin/shutdownReboot.xml Execute " "Shutdown Access PointWait until the LED turns REDPlug out power supplyTurn off the core appliancehttp://192.168.1.10/admin/shutdown.xmlExecute " "Shutdown DeviceWait for the device to shut down (LEDs off)Power switch " "OFFPlugin the ESL dongle to USB port "1"Turn on core appliance Power switch " "ONAdd the configuration for the ESL dongle with ID "50400" via Control Center: " "System Access Point Configuration
Document Title Goes HerePage 105. a. b. c. d. e. 6. 7. a. b. c. Fill " " with " " andAccess Point ID 50400" " with " "Host localhostSubmit changes by " "SaveWait until the ESL dongle's LED turns blueCheck the Access Point status via Control Center: " "System Access Point StatusAP-2010 is " "OFFLINEESL dongle is " "ONLINE
Document Title Goes HerePage 117. c. 1. 2. 3. 4. 5. 6. 1. 2. 3. Operate EMC TestTake the prepared Sample with the channel you want to evaluate (CH 0, 4, 10)Prepare the prepared counterpart with the same channel you chose (CH 0,4, 10)Plug-in the power supply of the counterpart and put in the batteries of the EUTThe AP and the Label now start automatically to permanently exchange packetsIf the transmission is OK, the LED will remain OFF. If a transmission fails the LED will be ON until the next successfultransmission of data. You can check the functionality if a you unplug the counterpart The LED of the EUT should light up within 2 seconds.Modulated/Unmodulated Output testTake the EUT and put in the batteriesthe label will send continuosly with maximum output powerYou can start all required measurements for the certification report

Navigation menu