SKYRC Technology 6X80BLUE AC/DC Fast Charger User Manual 6x80 BLUE MJ

Download:
Mirror Download [FCC.gov]
Document ID	1912859
Application ID	6acR7EhQZEJHsmJIOa9lyQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	151.29kB (1891132 bits)
Date Submitted	2013-03-07 00:00:00
Date Available	2013-03-07 00:00:00
Creation Date	2013-01-08 03:35:08
Producing Software	Corel PDF Engine Version 14.0.0.653
Document Lastmod	2013-01-08 03:35:08
Document Title	6x80+BLUE说明书_MJ.cdr
Document Creator	CorelDRAW
Document Author:	dzp

Fly your dream
FINALLY, YOUR CHARGER
GETS ITS OWN APP
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
All specifications and figures are subject to change without notice.
Printed in China
2012
Charge Master
Blue Version
TABLE OF CONTENTS
INTRODUCTION...................................................................................................... 01
SPECIAL FEATURES............................................................................................. 03
WARNING AND SAFETY NOTES......................................................................... 06
LITHIUM BATTERY CONNECTION DIAGRAM.................................................... 10
PROGRAM FLOW CHART...................................................................................... 12
OPERATION............................................................................................................ 14
LITHIUM BATTERY(LiPo/LiFe/LiIon)PROGRAM.................................................... 15
Charging Lithium Battery at Balance Mode................................................................ 15
Charging of Lithium Battery....................................................................................... 16
‘FAST' Charging of Lithium Battery............................................................................ 17
'STORAGE' Control of Lithium Battery....................................................................... 18
Discharging Lithium Battery....................................................................................... 19
NIMH/NICD BATTERY PROGRAM........................................................................ 20
Charging of NiMH/NiCd Battery................................................................................ 20
Charging NiMH/NiCd Battery in The AUTO Charge Mode........................................ 20
Discharging of NiMH/NiCd Battery............................................................................ 21
Charging NiMH/NiCd Battery In Re-Peak Charge Mode.......................................... 21
Charge/Discharge & Discharge/Charge Cycle of NiMH/NiCd Battery....................... 22
Pb( lead-sulphuric acid) battery program................................................................ 23
Charging of Pb Battery............................................................................................. 23
Discharging of Pb Battery.......................................................................................... 23
USING THE CHARGE CONTROL SOFTWARE “CHARGE MASTER”.................. 24
BATTERY MEMORY SET...................................................................................... 25
LITHIUM BATTERY METER.................................................................................. 27
MOTOR RPM TESTER.......................................................................................... 28
SERVO TESTER.................................................................................................... 29
SYSTEM SET UP.................................................................................................... 30
VARIOUS INFORMATION DURING THE PROCESS............................................. 32
WARNING AND ERROR MESSAGE.................................................................... 33
PAIRING CHARGER WITH SMART PHONE........................................................ 34
SPECIFICATION..................................................................................................... 36
RECOMMENDED ACCESSORIES........................................................................ 37
LIABILITY EXCLUSION........................................................................................ 38
CONFORMITY DECLARATION............................................................................. 38
WARRANTY AND SERVICE................................................................................. 39
INTRODUCTION
Congratulations on your choice of the SKYRC 6x80 Plus digital
intelligent charger from SKYRC Technology Co., Ltd.
The unit is simple to use, but the operation of a sophisticated automatic
charger such as SKYRC 6x80 Plus does require some knowledge on
the part of the user. These operating instructions are designed to
ensure that you quickly become familiar with its functions. It is
therefore important that you read right through the Operating
Instructions, Warning and Safety Notes before you attempt to use your
new automatic charger for the first time. We hope you have many
years of pleasure and success with your new battery charger.
SKYRC 6x80 Plus is a high-performance, micro processor control
charge/discharge station with battery management suitable for use with
all current battery types. With integral equalizer for six-cell, LithiumPolymer (LiPo), Lithium-Ferrum (LiFe) and Lithium-Ion (LiIon) batteries.
Maximum 10A charge current; maximum 80W charge power; can be
powered by a 12 Volt car battery or from 100V-240V via the built in
switch-mode power supply.
When a Nickel battery is fully charged, the unit terminates the process
using the Delta-Peak method. Lithium and lead (Pb) batteries are
charged using the CC-CV method.
The fan cooling system is so smart and efficient. The fan speed is
controlled by internal temperature sensor.
It also adds lithium Batt Meter, Motor RPM Tester and Servo Tester
functions. It is convenient for user to get some useful information with
this charger.
Finally, your charger gets its own apps. This charger can be controledl
and operated by smart phones.
It can be dangerous to mis-handle batteries and battery chargers, as
there is always a risk of batteries catching fire and exploding.
Please BE SURE to read these INSTRUCTIONS, WARNING and
SAFETY NOTES before you use the charger for the first time.
6X80 Plus
01
INTRODUCTION
SPECIAL FEATURES
Please read this entire operating manual completely and attentively
before using this product, as it covers a wide range of information on
operating and safety. Or please do use this product in company with a
specialist!
LCD Screen
Optimized Operating Software
SKYRC 6x80 Plus features the so-called AUTO function that set the
feeding current during the process of charging or discharging.
Especially for lithium batteries, it can prevent the overcharging which
may lead to an explosion due to the user's fault. It can disconnect the
circuit automatically and alarm once detecting any malfunction. All the
programs of this product were controlled through two way linkage and
communication, to achieve the maximum safety and minimize the
trouble. All the settings can be configured by users!
Internal Independent Lithium Battery Balancer
Enter/Start
Rotary Dial
Mode/Stop Button
Temp.
Sensor
DC Input
Power Cable
11-18V AC
Servo/ESC Port
Brushless Motor
Sensor Port
During the process of discharging, SKYRC 6x80 Plus can monitor and
balance each cell of the battery individually. Error message will be
indicated and the process will be ended automatically if the voltage of
any single one cell is abnormal.
Adaptable to Various Type of Lithium Battery
Fast and Storage Mode of Lithium Battery
USB Port for PC
Control & Firmware
Upgrade
Battery Socket
Bluetooth LED
Indicator
02
Balancing Individual Cells Battery Discharging
SKYRC 6x80 Plus is adaptable to various types of lithium batteries,
such as LiPo, LiIon and the new LiFe series of batteries.
AC Input
Power Port
100-240V AC
Balance Socket
Port Pitch=2.54mm
SKYRC 6x80 Plus employs an individual-cell-voltage balancer. It isn't
necessary to connect an external balancer for balance charging.
6X80 Plus
Purposes to charge lithium battery varies, 'fast' charge reduce the
duration of charging, whereas 'store' state can control the final voltage
of your battery, so as to store for a long time and protect useful time of
the battery.
Cyclic Charging/Discharging
1 to 5 cyclic and continuous process of charge>discharge or discharge
> charge is operable for battery refreshing and balancing to stimulate
the battery's activity.
6X80 Plus
03
SPECIAL FEATURES
SPECIAL FEATURES
Data Store/Load
Automatic Charging Current Limit
The charger can store up to 10 different charge/discharge profiles for
your convenience. You can keep the data pertaining to program setting
of the battery of continuous charging or discharging. Users can call out
these data at any time without any special program setting.
You can set up the upper limit of the charging current when charging
your NiMH or NiCd battery, it is useful for the NiMH battery of low
impedance and capacity in the 'AUTO' charging mode.
Terminal Voltage Control(TVC)
The charger allows user to change the end voltage.
Lipo Battery Meter
The user can check battery's total voltage, the highest voltage, the
lowest voltage and each cell's voltage.
Motor RPM Tester
Users connect the sensor motor and charger with sensor wire, set the
pulse width and test the RPM of the motor.
Capacity Limit
The charging capacity is always calculated as the charging current
multiplied by time. If the charging capacity exceeds the limit, the
process will be terminated automatically when you set the maximum
value.
Temperature Threshold*
The battery's internal chemical reaction will cause the temperature of
the battery to rise. If the temperature limit is reached, the process will
be terminated.
Servo Tester
* This function is available by connecting optional temperature probe, which is
not included in the package.
Connect the servo and the charger with wire, change the pulse width
value and check whether the servo works or not.
Processing Time Limit:
Re-Peak Mode of NiMH/NiCd Battery
You can also limit the maximum process time to avoid any possible
defect.
In re-peak charge mode, the charger can peak charge the battery
once, twice or three times in a row automatically. This is good for
making certain the battery is fully charged, and for checking how well
the battery receives fast charges.
Delta-peak Sensitivity for NiMH/NiCd
Delta-peak sensitivity for NiMH/NiCd battery: The automatic charge
termination program based on the principle of the Delta-peak voltage
detection. When the battery's voltage exceeds the threshold, the
process will be terminated automatically.
04
6X80 Plus
PC Control Software “Charge Master”
The free “Charge Master” software gives you unparalleled ability to
operate the charger through the computer. You can monitor pack
voltage, cell voltage and other data during the charging, view charge
date in real-time graphs. And you can initiate, control charging and
update firmware from “Charge Master”.
APPS for Smart Phone (both iOS and Android)
Finally, your charger gets its own apps. This charger can be controlled
and operated by smart phones.
6X80 Plus
05
WARNING AND SAFETY NOTES
WARNING AND SAFETY NOTES
These warnings and safety notes are particularly important. Please
follow the instructions for maximum safety; otherwise the charger and
the battery can be damaged or at worst it can cause a fire.
Never leave the charger unattended when it is connected to its
power supply. If any malfunction is found, TERMINATE THE
PROCESS AT ONCE and refer to the operation manual.
Keep the charger well away from dust, damp, rain, heat, direct
sunshine and vibration. Never drop it.
The allowable DC input voltage is 11-18V DC.
The allowable AC input voltage is 100-240V AC.
This charger and the battery should be put on a heat-resistant,
non-flammable and non-conductive surface. Never place them on
a car seat, carpet or similar surface. Keep all flammable volatile
materials away from the operating area.
Make sure you know the specifications of the battery to be
charged or discharged to ensure it meets the requirements of this
charger. If the program is set up incorrectly, the battery and
charger may be damaged. Fire or explosion can occur due to
overcharging. This warranty is not valid for any damage or
subsequent damage arising as a result of a misuse or failure to
observe the procedures outlined in this manual.
To avoid short circuiting between the charge lead, always connect
the charge cable to the charger first, then connect the battery.
Reverse the sequence when disconnecting.
Never attempt to charge or discharge the following types
of batteries:
A battery pack which consists of different types of cells
(including different manufacturers)
A battery that is already fully charged or just slightly discharged
Non-rechargeable batteries (pose an explosion hazard)
A faulty or damaged battery
A battery fitted with an integral charge circuit or a protection circuit
06
6X80 Plus
Batteries installed in a device or which are electrically linked to
other components
Batteries that are not expressly stated by the manufacturer to
be suitable for the currents the charger delivers during the
charge process
Please bear in mind the following points before commencing
charging:
Did you select the appropriate program suitable for the type of
battery you are charging?
Did you set up adequate current for charging or discharging?
Have you checked the battery voltage? Lithium battery packs
can be wired in parallel and in series, i.e. a 2-cell pack can be
3.7V (in parallel) or 7.4V (in series).
Have you checked that all connections are firm and secure?
Make sure there are no intermittent contacts at any point in the
circuit.
Standard Battery Parameters
LiPo
LiIon
LiFe
NiCd
MiMH
Pb
Nominal
Voltage
3.7V/cell
3.6V/cell
3.3V/cell
1.2V/cell
1.2V/cell
2.0V/cell
Max Charge
Voltage
4.2V/cell
4.1V/cell
3.6V/cell
1.5V/cell
1.5V/cell
2.46V/cell
Storage
Voltage
3.8V/cell
3.7V/cell
3.3V/cell
n/a
n/a
n/a
Allowable
Fast Charge
≦1C
≦1C
≦4C
1C-2C
1C-2C
≦0.4C
Min. Discharge
3.0-3.3V/cell 2.9-3.2V/cell 2.6-2.9V/cell 0.1-1.1V/cell 0.1-1.1V/cell
Voltage
1.8V/cell
Be very careful to choose the correct voltage for different types of battery otherwise you
may cause damage to the batteries. Incorrect settings could cause the cells to fire or
explode.
6X80 Plus
07
WARNING AND SAFETY NOTES
WARNING AND SAFETY NOTES
Charging
Discharging
During charge process, a specific quantity of electrical energy is
fed into the battery. The charge quantity is calculated by multiplying
charge current by charge time. The maximum permissible charge
current varies depending on the battery type or its performance,
and can be found in the information by the battery manufacturer.
Only batteries that are expressly stated to be capable of quickcharge are allowed to be charged at rates higher than the standard
charge current.
The main purpose of discharging is to clean the residual capacity
of the battery, or to reduce the battery' voltage to a defined level.
The same attention should be paid to the discharging process as
the charging process. The final discharge voltage should be set up
correctly to avoid deep discharging. Lithium batteries cannot be
discharged to lower than the minimum voltage, or it will cause a
rapid loss of capacity or a total failure. Generally, lithium batteries
don't need to be discharged. Please pay attention to the minimum
voltage of lithium batteries to protect them.
Connect the battery to the terminal of the charger: red is positive
and black is negative. Due to the difference between resistance of
cable and connector, the charger can not detect resistance of the
battery pack, the essential requirement for the charger to work
properly is that the charge lead should be of adequate conductor
cross-section, and high quality connectors which are normally goldplated should be fitted to both ends.
Always refer to the manual by the battery manufacturer pertaining
to charging methods. Operate according to their recommended
charging current and charging time. lithium batteries, in particular,
should be charged strictly according to the manufacturer’s
instruction.
Close attention should be paid to the connection of lithium
batteries.
Some rechargeable batteries have a memory effect. If they are
partly used and recharged before the whole charge is
accomplished, they remember this and will only use that part of
their capacity next time. This is a 'memory effect' It is said that
NiMH and NiCd batteries are suffering from memory effect. NiCd
has more ‘memory effect’ than NiMH.
Lithium batteries are recommended to be discharged partially
rather than fully. Frequent full discharging should be avoided if
possible. Instead, charge the battery more often or use a battery of
larger capacity. Full capacity cannot be reached until it has been
subjected to 10 or more charge cycles. The cyclic process of
charge and discharge will optimize the capacity of battery pack.
Do not attempt to disassemble the battery pack arbitrarily.
Please get highlighted that lithium battery packs can be wired in
parallel and in series. In the parallel connection, the battery's
capacity is calculated by multiplying single the battery's capacity by
the number of cells, bearing in mind that total voltage stays the
same. If the voltage is imbalanced, it may cause a fire or explosion.
Lithium batteries are recommended to charge in series.
08
6X80 Plus
6X80 Plus
09
LITHIUM BATTERY CONNECTION DIAGRAM
SKYRC 6x80 Plus comes with the built in switching power supply.
You can connect the AC power cord directly to the main AC socket.
(100-240V AC). For attaching directly to 12V car batteries. It is
critically important that you use a fully charged 13.8V car battery.
LITHIUM BATTERY CONNECTION DIAGRAM
This diagram shows the correct way to connect your battery to the
SKYRC 6x80 Plus while charging in the balance charge program mode
only.
NOTE: DC INPUT: The maximum charge circuit power is 80W.
AC INPUT: The maximum charge circuit power is 50W.
Using terminal
clip attaching
to car battery
CONNECTING THE BATTERY
Important!!! Before connecting a battery it is absolutely essential to
check one last time that you have set the parameters correctly. If the
settings are incorrect, the battery may be damaged, and could even
burst into flames or explode. To avoid short circuits between the
banana plugs, always connect the charge leads to the charger first,
and only then to the battery. Reverse the sequence when
disconnecting the pack.
WARNING:
Failure to connect as shown in this diagram will damage this charger.
Balance socket:
The balance wire attached to the battery must be connected to the
charger with the black wire aligned with the negative marking. Take
care to maintain correct polarity! (See the wiring diagram below.)
10
6X80 Plus
6X80 Plus
11
SELECT
PROGRAM SELECT
LiPo BATT
PROGRAM SELECT
Lilo BATT
SELECT
PROGRAM SELECT
LiFe BATT
SELECT
PROGRAM SELECT
Li BATT METER
SELECT
PROGRAM SELECT
SERVO TESTER
SELECT
PROGRAM SELECT
MOTOR RPM TESTER
SELECT
START
START
ENTER
START
ENTER
START
ENTER
START
ENTER
START
ENTER
START
ENTER
PROGRAM SELECT
NiCD BATT
PROGRAM SELECT
NiMH BATT
ENTER
START
ENTER
START
ENTER
START
START
ENTER
START
ENTER
ENTER
START
STOP
PROGRAM SELECT
Pb BATT
SELECT
ENTER
MODE
PROGRAM SELECT
BATT MEMORY
SELECT
PROGRAM SELECT
SYSTEM SET->
SELECT
SELECT
6X80 Plus
SELECT
1.00
BATT MEMORY [1]
C:4.9A D:2.2A
BATT MEMORY [1]
ENTER SET
VERSION
Rest Time
CHG>DCHG 10Min
PULSE WIDTH:1800
RPM: 00000
PULSE WIDTH:
700uS
4.20 4.19 4.19 V
0.00 0.00 0.00 V
LiFe BALANCE
2.0A 6.6V (2S)
Lilo BALANCE
2.0A 7.2V (2S)
LiPo BALANCE
2.0A 7.4V (2S)
NiMH CHARGE
CURRENT 2.0A
NiCD CHARGE
CURRENT 2.0A
Pb CHARGE
2.0A 2.0V (1P)
BATT MEMORY 3
Pb 4V (2S)
START
BATT MEMORY 2
NiMH 2.4V (2S)
SELECT
SELECT
SELECT
ENTER
START
ENTER
SELECT
ENTER
START
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
ENTER CHARGER
LOAD……
SELECT
SELECT
SELECT
SELECT
LiFe FAST CHG
2.0A 6.6V (2S)
Lilo FAST CHG
2.0A 7.2V (2S)
LiPo FAST CHG
2.0A 7.4V (2S)
NiMH Auto CHARGE
CURRENT 2.0A
NiCD Auto CHARGE
CURRENT 2.0A
Pb DISCHARGE
0.1A 2.0V (1P)
BATT TYPE
Pb
SAVE PROGRAM
ENTER
BATT TYPE
MiMH
LiPo BALANCE
4.9A 7.4V(2S)
BATT MEMORY [1]
LiPo 7.4V (2S )
BATT TYPE
LiPo
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
ENTER
START
SELECT
MODE/STOP
NiMH DISCHARGE
0.1A CUT: 1.0V
MODE/STOP
NiCD DISCHARGE
0.1A CUT: 1.0V
BATT VOLTS
4.0V (2S)
DELTA PEAK SENSE
4Mv/C
BATT VOLTS
2.4V (2S)
LiPo CHARGE
4.9A 7.4V(2S)
SAVE PROGRAM
SAVE….
BATT VOLTS
7.4V ( 2S )
LOAD FACTORY SET SELECT BLUETOOTH
ENTER
Clearing Memony
SELECT
SAFETY TIME
Capacity Cut-Off
ON
120Min
ON
5000mAH
MAIN 0.00V
H0.000V L0.000V
LiFe CHARGE
2.0A 6.6V (2S)
Lilo CHARGE
2.0A 7.2V (2S)
LiPo CHARGE
2.0A 7.4V (2S)
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
ON
ON
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
DEC
0C
37C
TRICKLE
100mA
LiPo STORAGE
4.9A 7.4V(2S)
TEMPERATURE
CUT-OFF 50C
DSCH CURRENT
2.2A
Ext. Temp
Int. Temp
INC
Input Power Low
Cut-Off
11.0V
LiFe DISCHARGE
2.0A 6.6V (2S)
Lilo DISCHARGE
2.0A 7.2V (2S)
LiPo DISCHARGE
2.0A 7.4V (2S)
NiMH RE-PEAK
NiCD RE-PEAK
CHARGE CURRENT
3.3A
SELECT
SELECT
SELECT
NiMH CYCLE
CHG>DCHG
NiCD CYCLE
CHG>DCHG
SAVE PROGRAM
ENTER
DSCH CURRENT
1.5A
DSCH VOLTAGE SELECT DSCH CURRENT
1.1V/CELL
2.2A
CHARGE CURRENT
3.3A
LiPo FAST CHG
4.9A 7.4V(2S)
SAVE PROGRAM
ENTER
CHARGE CURRENT
4.9A
BLUETOOTH
Active Pairing
Key Beep
Buzzer
LiFe STORAGE
2.0A 6.6V (2S)
Lilo STORAGE
2.0A 7.2V (2S)
LiPo STORAGE
2.0A 7.4V (2S)
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
SELECT
DSCH VOLTAGE
3.0V/CELL
PEAK DELAY
DSCH VOLTAGE
1.7V/CELL
TEMPERATURE
CUT-OFF 50C
1Min
LiPo DISCHARGE
2.2A 7.4V(2S)
TVC=YOUR RISK
4.20V
SELECT
6X80 Plus
SELECT
12
TEMPERATURE
CUT-OFF 50C
SELECT
PROGRAM FLOW CHART
PROGRAM FLOW CHART
13
OPERATION
LITHIUM BATTERY(LiPo/LiFe/LiIon)PROGRAM
The most important tool to operate the charger is the red rotary dial
and black button.
Mode/Stop Button
Enter/Start Rotary Dial
Enter/Start Rotary Dial
The dial has three functions: rotating the dial in both directions will
scroll through menus and adjust parameters quickly and easily, and
pressing down on the dial acts as button which is often used to enter
parameter alert or store parameters on-screen.
Mode/Stop Button
It is used to stop the progress or go back to previous step/screen.
When you are willing to alter the parameter value in the program, press
the dial to make it blink then change the value by rotating the dial
clockwise or counterclockwise. The value will be stored by re-pressing
the dial. When you are willing to start the progress, press and hold the
dial for 3 seconds. When you are willing to stop the progress or go
back to previous step/screen, press the button once.
When you power on the charger, it will enter LiPo Battery balance
program directly. You could change the mode (balance mode, normal
charge mode, fast charge mode, store mode or discharge mode), enter
the desired charging/discharging mode, set the referred parameter and
start the progress.
If you have no request for LiPo Battery program, please press the
button to enter Program Select screen.
14
These programs are only suitable for charging and discharging lithium
batteries with a nominal voltage of 3.7V, 3.6V and 3.3V per cell. These
batteries need to adopt different charge technique which is termed as
constant voltage(CV) and constant current(CC) method. The charge
current varies according to the battery capacity and performance. The
final voltage of charge process is also very important; it should be
precisely matched with the charge voltage of the battery. They are 4.2V
for LiPo, 3.6 V for LiFe, and 4.1V for Lilon. The charge current and
nominal voltage as for cell count set on the charge program must
always be correct for the battery to be charged.
6X80 Plus
CHARGING LITHIUM BATTERY AT BALANCE MODE
This function is for balancing the voltage of lithium-polymer battery
cells while charging.
In the balance mode, the battery needs to connect to the battery's
power lead with balance wire.
In this mode, the charging process will be different from ordinary
charging mode. The internal processor of the charger will monitor the
voltages of each cell of the battery pack and control charging current
which is feeding to each cell to equalize the voltage.
Note: We recommend charging lithium batteries with a balance wire in
the balance mode only.
- +
- +
SELECT
SELECT
Mode
Stop
Press
Dial > 3 seconds
6X80 Plus
The left side of the first line shows the type
of battery you choose. The value on the left
of the second line of the charger is current
the user sets. After setting the current and
voltage, press and hold the dial for 3
seconds to start the process.
15
LITHIUM BATTERY(LiPo/LiFe/LiIon)PROGRAM
This screen displays the number of cells you
set up and the processor detects. R shows
the number of cells detected by the charger
and S is the number of cells set by you at
the previous screen. If both numbers are
identical you can start charging process. If
not, press button to go back to previous
screen to recheck the number of cells of the
battery pack before going ahead.
Press
Dial
Number Charging
Battery
of
voltage Charged
time
capacity
cells
Charging
current
This screen shows the real-time status during
charge process. Press button once to stop
the charge process.
CHARGING OF LITHIUM BATTERY
This charging mode is for charging LiPo/LiFe/LiIon battery in normal
mode.
Note: We recommend charging lithium batteries with a balance lead in
the balance mode only.
- +
- +
SELECT
Mode
Stop
LITHIUM BATTERY(LiPo/LiFe/LiIon)PROGRAM
SELECT
Press
> 3 seconds
Dial
The left side of the first line shows the type
of battery you choose. The value on the left
of the second line of the charger is current
the user sets. After setting the current and
voltage, press and hold the dial for 3
seconds to start the process.
Press
Dial
Number Charging
Battery
of
voltage Charged
time
capacity
cells
Charging
current
6X80 Plus
This screen shows the real-time status
during charge process. Press button once to
stop the charge process.
‘FAST' CHARGING OF LITHIUM BATTERY
The charging current is getting smaller as the process goes to the near
end term of Lithium battery charging. To finish charging process earlier,
this program eliminate certain period of CV process. Actually, the
charging current will goes to 1/5 from the initial value to end the
process while the normal charging goes to 1/10 during CV period. The
charging capacity may be a bit smaller than normal charging but the
process time will be reduced.
- +
- +
SELECT
SELECT
Mode
Stop
Press
> 3 seconds
Dial
The value on the left side of the second lines
shows the charge current. The value on the
right side of the second lines shows the
battery pack's voltage. After setting current
and voltage, press and hold the dial for 3
seconds to start the process.
This displays the number of cells you set up
and the processor detects. R shows the
number of cells detected by the charger and
S is the number of cells set by you at the
previous screen. If both numbers are
This displays the number of cells you set up
and the processor detects. R shows the
number of cells detected by the charger and
16
S is the number of cells set by you at the
previous screen. If both numbers are
identical you can start charging process. If
not, press button to go back to previous
screen to recheck the number of cells of the
battery pack before going ahead.
6X80 Plus
17
LITHIUM BATTERY(LiPo/LiFe/LiIon)PROGRAM
Press
Dial
Charging Supplied Current
Number time
capacity voltage
battery
of
Charge
cells
current
identical you can start charging process. If
not, press button to go back to previous
screen to recheck the number of cells of the
battery pack before going ahead.
This screen shows the real-time status
during charge process. Press button once to
stop the charge process.
This program is for charging or discharging Lithium battery which will
not be used for long time. The program will determine to charge or
discharge the battery to certain voltage depending on the voltage of the
battery at its initial stage. They are different from the type of the battery,
3.75V for LiIo, 3.85V for LiPo and 3.3V for LiFe per cell. If the voltage
of battery at its initial stage is over the voltage level to storage, the
program will start to discharge.
- +
- +
SELECT
Mode
Stop
18
Press
> 3 seconds
Dial
previous screen to recheck the number of
cells of the battery pack before going ahead.
Press
Dial
Current
NumberElapsed Supplied voltage
capacity
time
of
battery
Charge
cells
or discharge
current
This screen shows the real-time status
charging. Press Mode/Stop button once to
stop the charge process.
DISCHARGING LITHIUM BATTERY
'STORAGE' CONTROL OF LITHIUM BATTERY
SELECT
LITHIUM BATTERY(LiPo/LiFe/LiIon)PROGRAM
At this screen, you can set up the current
and voltage of the battery pack. Charging
and discharging will make the batteries
come to the voltage level of storage state.
This screen displays the number of cells you
set up and the processor detects. R shows
the number of cells detected by the charger
and S is the number of cells set by you at
the previous screen. If both numbers are
identical you can start charging process. If
not, press Mode/Stop button to go back to
6X80 Plus
- +
- +
SELECT
SELECT
Mode
Stop
Press
Dial > 3 seconds
Press
Dial
Discharged
Number elapsed
Battery capacity
time
of
discharge voltage
cells
current
6X80 Plus
The value of discharge current on the left
can not exceed 1C, and the value on the
right can not be under the voltage
recommended by the manufacturer to avoid
over discharging. Press and hold the dial for
3 seconds to start discharging.
This screen displays the number of cells you
set up and the processor detects. R shows
the number of cells detected by the charger
and S is the number of cells set by you at
the previous screen. If both numbers are
identical you can start charging process. If
not, press Mode/Stop button to go back to
previous screen to recheck the number of
cells of the battery pack before going ahead.
This screen shows the real-time status of
discharging, you can press Mode/Stop
button to stop discharging.
19
NIMH/NICD BATTERY PROGRAM
NIMH/NICD BATTERY PROGRAM
These programs are for charging or discharging NiMH (Nickel-MetalHydride) or NiCd (Nickel-Cadmium) battery.
CHARGING OF NIMH/NICD BATTERY
The charger will charge NiMH and NiCd batteries using the charge
current set by the user.
This program is for charging of NiMH/NiCd
NiMH CHARGE
batteries. You can press Start/Enter dial to
CURRENT
2.0A
make the parameter blink, then rotate the
dial to change the value and repress the dial
- +
Battery
type
SELECT
to store the value.
Press
Dial > 3 seconds
Mode
Stop
Battery
Elapsed
Battery time Chargevoltage Charged
type
capacity
current
The screen displays the current state of
charging.
To stop the process, press Mode/Stop
button once.
The audible sound indicates the end of
process.
CHARGING NIMH/NICD BATTERY IN THE AUTO
CHARGE MODE
In this program the charger detects the condition of the battery which is
connected to the output and automatically charges the battery. In this
mode, you should set up the upper limit of the charge current to avoid
damage by excessive feeding current. Some batteries of low
resistance and capacity can lead to higher current in the auto charging
mode.
NiMH Auto
CURRENT
CHARGE
2.0A
Battery
type
Mode
Stop
20
Press
Dial > 3 seconds
This program is for charging of NiMH/NiCd
batteries in auto mode. You can press
Start/Enter dial to make it blink and then rotate
the dial to change the parameter value. Press
START/ENTER dial to store the value.
6X80 Plus
NiMH 2.0A
AUT 000:13
9.52V
00000
Battery
Elapsed
Battery time Chargevoltage Charged
type
capacity
current
The screen displays the current state of
charging.
To stop the process, press Mode/Stop
button once.
The audible sound indicates the end of
process.
CHARGING NIMH/NICD BATTERY IN RE-PEAK
CHARGE MODE
Re-peak Charge Mode (NiMH and NiCd batteries only): In re-peak
charge mode, the charger can peak charge the battery once, twice or
three times in a row automatically. This is good for confirming the
battery is fully charged, and for checking how well the battery receives
fast charges. A five minute cool-off delay occurs after each re-peak
charge. To start charge, press and hold the dial for 3 seconds.
NiMH RE-PEAK
- +
Press
Dial
NiMH 2.0A
RPC 000:33
SELECT
9.59V
00017
Re-peak cycle number 1 shows on the display.
Press the dial to make the re-peak cycle
number blink and rotate the dial to find the
desired number of times to re-peak charge the
battery.
Press the dial to confirm selection.
Charged
Battery Elapsed
capacity
time
type
Charge
Battery
current
voltage
DISCHARGING OF NIMH/NICD BATTERY
NiMH DISCHARGE
0.1A
CUT:1.0V
- +
Battery
type
Mode
Stop
SELECT
Press
Dial > 3 seconds
6X80 Plus
Set discharge current on the left and final
voltage on the right. The discharge current
ranges from 0.1 to 5.0A and the final voltage
ranges from 0.1 to 25.2V. To start the
process, press and hold Start /Enter dial for
3 seconds.
21
NIMH/NICD BATTERY PROGRAM
NiMH
DSC
PB( LEAD-SULPHURIC ACID) BATTERY PROGRAM
The screen indicates the discharging state.
You can rotate the Start/Enter dial to alter
discharge current and repress the dial to
store the value. Press Mode/Stop button to
Discharged
capacity stop discharging.
The audible sound indicates the end of
process.
0.1A 7.42V
022:45 00890
Battery
Battery Elapsed
time
voltage
type
Discharge
current
CHARGE/DISCHARGE & DISCHARGE/CHARGE CYCLE
OF NIMH/NICD BATTERY
NiMH CYCLE
CHG＞DCHG
- +
- +
SELECT
SELECT
Mode
Stop
NiMH 1.0A
C>D 022:45
You can set up sequence on the left and the
number of cycles on the right. Range of the
cycle number is 1-5.
This is programmed for charging Pb (lead-sulphuric acid) battery with
nominal voltage from 2 to 20V. Pb batteries are totally different from
NiMH or NiCd batteries. They can only deliver relatively lower current
comparing to their capacity, and similar restrictions definitely apply to
charge. So the optimal charge current will be 1/10 of the capacity. Pb
batteries must not be charged rapidly. Always follow the instruction
supplied by the battery manufacturer.
CHARGING OF PB BATTERY
- +
- +
SELECT
SELECT
Mode
Stop
Press
Dial > 3 seconds
7.42V
00890
Press Mode/Stop key to stop program, you
can rotate the Start/Enter dial to alter the
current.
Elapsed Battery Discharged
Battery time
voltage or charged
type
capacity
Discharge
or charge
current
Charged
Battery Elapsed Battery capacity
voltage
time
type
Charge
current
The screen displays the state of charging
process. To stop charging forcibly, press
Mode/Stop button once.
The audible sound indicates end of process.
DISCHARGING OF PB BATTERY
- +
- +
SELECT
SELECT
Mode
Stop
22
Press
Dial > 3 seconds
Set up the charge current on the left and the
nominal voltage of the battery on the right.
The charge current ranges from 0.1 to 10.0A
and the voltage should be matched with the
battery being charged. Start the charge
process by pressing and holding the dial for
3 seconds.
6X80 Plus
Set discharge current on the left and final
voltage on the right. The discharge current
ranges from 0.1 to 5.0A.
To start the process, press and hold the
Start/Enter dial for 3 seconds.
Press
Dial > 3 seconds
6X80 Plus
23
USING THE CHARGE CONTROL SOFTWARE
“CHARGE MASTER”
The screen displays the current state of
discharge. You can alter the discharge
current by pressing Start/Enter dial during
Battery
Battery Elapsed
voltage
the process. Once you find the desired
time
type
Discharge
Discharged current value by rotating the dial, store it by
current
capacity
repressing the dial.
To stop discharging, press Mode/Stop button
once. The audible sound indicates the end
of process.
BATT MEMORY【1】
ENTER SET
Press
Dial ＞3 seconds
BATT TYPE
LiPo
BATT VOLTS
7.4V(2S)
SELECT
DSCH CURRENT
2.2A
SELECT
SELECT
6X80 Plus
Set the voltage and number of cells, along with
the normal voltage (1S-6S).
Set the charge current, which can be adjusted(0.110.0A).
SELECT
Set the discharge current, which can be adjusted
(0.1A-5.0A).
SELECT
DSCH VOLTAGE
3.0V/CELL
24
Enter the battery memory program, you can
change the battery type(LiPo, LiFe, LiIon, NiMH,
NiCd, Pb battery), voltage, charge current by
pressing the Start/Enter dial to make the value
blink, then rotate the Start/Enter dial clockwise or
counterclockwise to alter the value, and repress
Start/Enter dial to store the value and move to the
next value or screen.
Note:The battery used for this example is a
2S(7.4V) Lipo battery.
SELECT
CHARGE CURRENT
4.9A
SELECT
The free “Charge Master” software gives you unparalleled ability to
operate the charger through the computer. You can monitor pack
voltage, cell voltage and other data during the charging process, view
charging data in real-time graphs. And you can initiate, control charging
and update firmware from “Charge Master”.
In order to connect the charger to the computer and use the “Charge
Master”, you are required to use a USB cable which is not included in
this package. The cable must be terminated on one end with “A” plug
and the opposite end is terminated with “mini-B” plug which can
connect to the charger directly.
The “Charge Master” can be download from www.skyrc.com. For more
details, please refer to HELP file which can be found in “Charge
Master” software.
The charger can store up to 10 different charge/discharge profiles for
your convenience, and the stored profiles can be recalled quickly
without having to go through the setup process.
SELECT
USING THE CHARGE CONTROL SOFTWARE
“CHARGE MASTER”
BATTERY MEMORY SET
Set the discharge voltage, which can be adjusted
(3.0-3.3V/Cell).
SELECT
6X80 Plus
25
BATTERY MEMORY SET
TVC=YOUR RISK
4.20V
LITHIUM BATTERY METER
Set the terminal voltage, which can be
adjusted(4.18-4.30V).
SELECT
SELECT
TEMPERATURE
CUT-OFF
50C
The user can check battery's total voltage, the highest voltage, the
lowest voltage and each cell's voltage.
Please connect the battery to the charger main battery lead to battery
socket and balance wires to balance socket.
Set the cut-off temperature, which can be
adjusted(20 C/68 F-80 C/176 F).
SELECT
SELECT
SAVE PROGRAM
ENTER
SELECT
SAVE PROGRAM
SAVE
Save the program set by pressing and holding
the Start/Enter dial for 3 seconds.
This diagram shows the correct
way to connect your battery to
check the voltage.
Press
Dial ＞3 seconds
BATT MEMORY【1】
LiPo 7.4V(2S)
This screen indicate the saved profile.
next flash
BATT MEMORY【1】
C:4.9A
D:2.2A
26
This screen indicates that the charge profile is
being loaded.
6X80 Plus
PROGRAM SELECT
Li
BATT METER
Press the Start/Enter dial to enter the Lithium
Battery Meter program.
Press
Dial
4.19
0.00
4.15
0.00
4.18V
0.00V
The screen indicate each cell's voltage.
SELECT
SELECT
ENTER CHARGER
LOAD……
Once you've saved a charge profile, you can
load those settings to use later. To load a
memory, you have to press and hold the
Start/Enter dial for 3 seconds. Otherwise you
only enter the setting mode.
MAIN 12.52V
H4.190V
L4.160V
6X80 Plus
The screen indicate the total voltage, the highest
voltage, the lowest voltage.
27
MOTOR RPM TESTER
SERVO TESTER
The charger can test motor RPM. Please do as follows,
1. Connect the motor and ESC.
2. Switch off the ESC and connect it to the battery.
3. Connect the power to the charger.
4. Insert the ESC signal wire to ESC port in the charger.
5. Connect the motor and charger with motor sensor wire. There is a motor
sensor port beside the temp sensor.
6. Enter Motor RPM Tester Program, set the initial pulse width which should be
the same as the neutral position of the transmitter. We suggest to set it to 1480
as most of the transmitters’ neutral position is like that.
7. Switch on the ESC. Change the pulse width and check the RPM corresponding
to different pulse width. If the motor doesn’t run, please recheck the transmitters’
neutral position and reset the initial pulse width.
The charger can check whether the servo works. Please do as follows,
1. Connect the battery to the power.
2. Connect the servo to the servo port in left side of the charger. Be
careful with the correct polarity.
3. Enter to Servo Tester Program in the charger, change the pulse
width and check the response of the servo.
This diagram shows the correct connect way to test the servo.
This diagram shows the
correct connect way to
test motor RPM.
SELECT
PULSE WIDTH:1500
RPM: 00000
SELECT
28
Press the Start/Enter dial to enter the Motor RPM Tester
Program and set the initial pulse width by rotating the
Start/Enter knob.
Switch on the ESC.
The left side of the first line shows the pulse width and
the second line shows the RPM of the motor
corresponding to different pulse width. The value of
pulse width can be changed by rotating the Start/Enter
dial.
6X80 Plus
SELECT
PROGRAM SELECT
MOTOR RPM TESTER
PROGRAM SELECT
SERVO TESTER
PULSE WIDTH:
900uS
Press the Start/Enter dial to enter the Servo
Tester Program.
The screen displays the pulse width. Rotate the
Start/Enter dial to change the value of pulse
width and observe the response of the servo
corresponding to different pulse width
SELECT
6X80 Plus
29
SYSTEM SET UP
SYSTEM SET UP
It will be operated with the default value of the essential user settings
when it is connected to a DC 11~18V battery for the first time. The
screen displays the following information in sequence and the user can
change the value of parameter on each screen.
When you are willing to alter the parameter value, press the dial to
make it blink then change the value by rotating the dial clockwise or
counterclockwise. The value will be stored by repressing the dial.
PROGRAM SELECT
SYSTEM SET
SELECT
User set up starting screen.
6X80 Plus
SELECT
ON
ON
SELECT
Input Power Low
Cut-Off
11.0V
Ext. Temp
Int. Temp
SELECT
0C
37C
Capacity
Current
Safety Time
2000mAh
3300mAh
2.0A
3.0A
(2000/2.0=1000)/11.9=84 minutes
1000mAh
1.2A
(1000/1.2=833)/11.9=70 minutes
(3300/3.0=1100)/11.9=92 minutes
This program sets the maximum charge
capacity that will be supplied to the battery
during charge. If the deltapack voltage is not
detected nor the safety timer expired by any
reason, this feature will automatically stop the
process at the selected capacity value.
The beep sounds at every time pressing the
buttons to confirm your action. The beep or
melody sounded at various times during
operation to alert different mode changes.
These audible sounds can be on or off.
This program monitors the voltage of input
battery. If the voltage drops below the value
you set the operation forcibly terminated to
protect the input battery.
This screen shows the external and internal
temperature.
SELECT
Safe timer Calculation
When charging NiMH or NiCd batteries, divide
the capacity by current, then divide the result
Key Beep
Buzzer
SELECT
SELECT
When you start a charge process, the integral
safety timer automatically starts running at the
same time. This is programmed to prevent
overcharge the battery if it proves to be faulty,
or if the termination circuit cannot detect the
battery full. The value for the safety timer
should be generous enough to allow a full
charge of the battery.
SELECT
SELECT
SELECT
The battery is on the cyclic process of charge
and discharge can often become warm after
charge or discharge period. The program can
insert a time delay to occur after each charge
and discharge process to allow the battery
adequate time to cool down before being
subjected to the next process. The value
ranges from 1 to 60 minutes.
SELECT
SELECT
SELECT
SAFETY TIME
ON
120Min
30
For example:
Capacity Cut-Off
ON
5000mAH
Rest Time
CHG＞DCHG 10Min
SELECT
by 11.9, set this number as the value for
safety timer setting. If the charger stopped at
this threshold, about 140% of the capacity will
have been fed into the battery.
6X80 Plus
31
VARIOUS INFORMATION DURING THE PROCESS
LOAD FACTORY SET
ENTER
Press and hold the Start/Enter dial for 3 seconds
to load the factory set.
SELECT
1.00
This screen shows the version.
VARIOUS INFORMATION DURING THE PROCESS
You can inquire various information on LCD screen during charging or
discharging process. When you rotate the dial counterclockwise, the
screen will display the user’s settings.
And also you can monitor the voltage of individual cell by rotating the
dial clockwise when the individual connection cable is linked to the
Lithium battery being processed.
0C
26C
4.18V
0.00V
The Battery connection is wrong.
BALANCE CONNECT
ERROR
The balance connect is wrong.
DC IN TOO LOW
Input voltage less than 11V.
DC IN TOO HIGH
Input voltage higher than 18V.
CELL ERROR
HIGH VOLTAGE
Voltage of one cell in the battery pack is too high.
CELL ERROR
VOLTAGE-INVALID
Voltage of one cell in the battery pack is invalid.
CELL NUMBER
INCORRECT
The cell number is wrong.
INT.TEMP.TOO HI
The internal temperature of the unit goes too high.
EXT.TEMP.TOO HI
The external temperature of the unit goes too high.
OVER CHARGE
CAPACITY LIMIT
The battery capacity is more than the maximum
capacity which the user sets.
Displayed capacity cut-off function is turn on and
the setting value of capacity.
OVER TIME LIMIT
The charging time is longer than the maximum
charging time which the user sets.
The battery is connected with balance lead, you
can check voltage of each cell in the battery pack.
BATTERY WAS FULL
The battery voltage is higher than the maximum
voltage which the user sets when charging in
balance mode.
This screen shows the internal temperature.
Displayed safety timer is turn on and duration of
time in minutes.
4.15
0.00
CONNECT ERROR
CHECK MAIN PORT
Voltage of one cell in the battery pack is too low.
Present input voltage.
Ext. Temp
Int. Temp
The battery is interrupted.
CELL ERROR
LOW VOLTAGE
It comes to the final voltage when the program
ended.
32
It incorporates a variety of functions for the systems to verify processes
and the state of the electronics. In case of an error the screen will
display the cause of error and emit an audible sound.
Incorrect polarity connected.
VERSION
4.19
0.00
WARNING AND ERROR MESSAGE
6X80 Plus
6X80 Plus
33
PAIRING CHARGER WITH SMART PHONES
PAIRING CHARGER WITH SMART PHONES
Pairing occurs when two Bluetooth devices communicate with each
other and establish a connection. A record of information about this
connection is then stored in the memory of each device. Once you pair
a device with the 6X80 charger, you should not have to pair it again.
The 6X80 charger can pair with up to eight devices. However, it can
only connect to, and control the 6X80 charger from one device at a
time.
To begin pairing with your iPhone, iPod or iPad
1. With 6X80 Charger is turned on, under BLUETOOTH MENU and
press “Rotary Enter Button” to active Bluetooth pairing and make
the charger discoverable. The Bluetooth indicator on the charger is
blinking in blue to show the charger is discoverable.
PROGRAM SELECT
SYSTEM SET->
Press
Dial
BLUETOOTH
Active Pairing
Press
Dial
BLUETOOTH
Discoverable
SELECT
2. Select the Bluetooth menu from your iPhone or iPod and ensure
the Bluetooth is turned on.
3. Find the 6X80 Charger which will be identified as “SkyRC + 4 digits
serial number”. For example, SkyRC1234 and select it.
4. Confirm that you want to connect the 6X80 Charger with your
iPhone or iPod by selecting it.
5. A confirmation “Connected” appears on your phone after you have
selected the 6X80 Charger. It takes few seconds to finalize the
pairing process, please wait for while.
6. The Bluetooth indicator, located on the right side of charger
remains steadily on.
7. Your 6X80 Charger is now connected with your iPhone or iPod.
34
6X80 Plus
On your Android device:
1. With 6X80 Charger is turned on, under BLUETOOTH MENU and
press “Rotary Enter Button” to active Bluetooth pairing and make
the charger discoverable. The Bluetooth indicator on the charger
blinking to show the charger is discoverable.
Press
Dial
PROGRAM SELECT
SYSTEM SET->
BLUETOOTH
Active Pairing
Press
Dial
BLUETOOTH
Discoverable
SELECT
2. When the ChargeMaster starts in Android, bluetooth will be enabled
and paired automatically.
Useful notes and tips
You can only connect your 6X80 Plus with one device at a time.
The Charger can hold up eight paired devices. When the memory is full
and additional device cannot be paired. If you want to pair new
devices, you need clearing all the memory.
Clearing memory
To clear the Charger memory of all devices, select “Clearing Memoery”
from BLUETOOTH menu and press Rotary button once. The charger
clears all devices from its memory and “No Memory” will display on the
screen.
PROGRAM SELECT
SYSTEM SET->
Press
Dial
SELECT
BLUETOOTH
Active Pairing
BLUETOOTH
Clearing Memory
SELECT
Press
Dial
BLUETOOTH
No Memony
6X80 Plus
35
SPECIFICATION
RECOMMENDED ACCESSORIES
SPECIFICATION
AC Input
100-240V
DC Input
11-18Volt
Charge circuit power
AC Input 50W
DC Input 80W
Charge current range
Discharge current power
0.1-10.0A
Discharge current range
0.1-5.0A
Current drain for balancing port
200mA/cell
NiCd/NiMH battery cell count
1-15Cells
LiPo/LiFe/Lilon cell count
1-6Cells
Pb battery voltage
2-20V
Net weight
525g
Dimension
135x112x60.9mm
Temp. Sensor Cable
TP/FP Adaptor
HP/PQ Adaptor
SK-600005-01
SK-600018-02
SK-600016-03
8W
(stated values refer to one charger except built-in power supply, dimension & weight)
EH Adaptor
XH Adaptor
Tamiya charging cable
SK-600014-01
SK-600020-04
5201-0030-01
JST/BEC charging cable
Dean charging cable
Futaba RX charging cable
5201-0043-01
5201-0012-01
5201-0044-01
TRAXXAS charging cable
Glow charging cable
Crocodile clip charging cable
5201-0033-01
5201-0045-01
5201-0031-01
THE SET CONTAINS
1. SKYRC 6x80 Plus Charger
2. XH Adaptor
3. Power Cord
4. 18AWG Wire Charging
Cable
EC3 charging cable
5201-0034-01
36
6X80 Plus
6X80 Blue
6X80
Plus
37
LIABILITY EXCLUSION
WARRANTY AND SERVICE
This charger is designed and approved exclusively for use with the types of
battery stated in these Instruction Manual. SKYRC accepts no liablility of
any kind if the charger is used for any purpose other than that stated. We
are unable to ensure that you follow the instructions supplied with the
charger, and we have no control over the methods you employ for using,
operating and maintaining the device. For this reason we are obliged to
deny all liability for loss, damage or costs which are incurred due to the
incompetent or incorrect use and operation of our products, or which are
connected with such operation in any way. Unless otherwise prescribed by
law, our obligation to pay compensation, regardless of the legal argument
employed, is limited to the invoice value of those SKYRC products which
were immediately and directly involved in the event in which the damage
occurred.
CONFORMITY DECLARATION
SKYRC 6x80 Plus satisfies all relevant and mandatory CE directives and
FCC SubPart C Intentional Radiators section 15.247
The product has been tested to meet the following technical standards:
Test Standards
CE-LVD
Result
Title
EN60335-2-29
For safety of household and similar electrial appliances
Conform
EN 300328
Wideband transmission systems; Data transmission
equipment operating in the 2,4 GHz ISM band and using
wide band modulation techniques article 3.1(b) EMC
requirements
Conform
EN 301489-1
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services. Part 1: Common technical
requirements
Conform
EN 301489-17
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services. Part 17:Specific conditions
for Broadband Data Transmission Systems article 3.1(a)
Health requirements
Conform
EN 62479
Assessment of the compliance of low power electronic
and electrical equipment with the basic restrictions related
to human exposure to electromagnetic fields (10 MHz to
300 GHz) article 3.1(a) Safety
Conform
Operation within the bands 902 - 928 MHz, 2400 2483.5 MHz, and 5725 - 5850 MHz.
Conform
38
FCC SubPart C Intentional
Radiators section 15.247
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
This symbol means that you must dispose of electrical devices from the
General household waste when it reaches the end of its useful life. Take
your charger to your local waste collection point or recycling centre. This
applies to all countries of the European Union, and to other European countries
with a separate waste collection system.
WARRANTY AND SERVICE
CE-R&TTE
FCC
FCC Note
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or tv interference caused by unauthorized
modifications to this equipment. such modifications could void the user’s authority to operate
the equipment.
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed
and operated with a minimum distance of 20cm between the radiator and your body.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
6X80 Plus
We guarantee this product to be free of manufacturing and assembly defects for
a period of one year from the time of purchase. The warranty only applies to
material or operational defects, which are present at t he time of purchase.
During that period, we will repair or replace free of service charge for products
deemed defective due to those causes.
You will be required to produce proof of purchase (invoice or receipt). This
warranty is not valid for any damage or subsequent damage arising as a result of
misuse, modification or as a result of failure to observe the procedures outlined in
this manual.
39
SCAN WITH YOUR SMART PHONE
FINALLY, YOUR CHARGER
GETS ITS OWN APP
Scan with
your iPhone
to download.
Scan with
your Android
to download.
40
6X80 Plus

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 22
Create Date                     : D:20130108033508Z
Modify Date                     : D:20130108033508Z
Producer                        : Corel PDF Engine Version 14.0.0.653
Author                          : dzp
Creator                         : CorelDRAW
Title                           : 6x80+BLUE说明书_MJ.cdr

EXIF Metadata provided by EXIF.tools