SMC Networks AR9381DB24 Wireless Data Gateway User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2580639
Application ID	Jq03ZXwQE1grnWI2fwGEtg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.72kB (146525 bits)
Date Submitted	2015-04-10 00:00:00
Date Available	2015-10-07 00:00:00
Creation Date	2017-10-08 16:20:13
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-08 16:20:13
Document Title	User Manual
Document Creator	Adobe InDesign CS6 (Windows)

DOCSIS 3.0 Wireless Gateway Installation Instructions
Important Safety Instructions
Read these instructions before you begin
When using your equipment, basic safety precautions should always be followed to reduce the risk of ire,
electric shock, and injury to persons, including the following:
•
•
•
•
•
•
•
•
•
•
•
•
Read and follow these instructions.
Keep these instructions.
Heed all warnings.
Only use attachments/accessories speciied by the manufacturer.
Do not install near any heat sources.
Clean only with a dry cloth.
Do not block any ventilation openings.
Use only with the cart, stand, tripod, bracket, or table speciied by the manufacturer, or sold with the
apparatus.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualiied service personnel. Servicing is required when the apparatus has been
damaged in any way, such as when a power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Do not alter or disable the polarized or grounding-type (three-pronged) plug.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
SMC Wireless Gateway complies with applicable requirements for performance, construction, labeling, and
information when used in accordance with the instructions below:
WARNING: Risk of Shock
Mains voltages inside this unit. No user serviceable parts inside. Refer service to qualiied personnel
only! Avoid using and/or connecting the equipment during an electrical storm, to avoid risk of electrocution.
AVERTISSEMENT: Risque d’électrocution
Tensions du secteur dans cette unité. Ne contient aucune pièce pouvant être réparée par l’utilisateur.
Tout entretien doit être effectué par du personnel qualiié seulement!
• Do not use this product near water (i.e. wet basement, bathtub, sink or near a swimming pool, etc.) to
avoid risk of electrocution.
• Avoid using and/or connecting the equipment during an electrical storm, to avoid risk of electrocution.
• Do not locate the equipment within 6 feet (1.9m) of a lame or ignition source (i.e. heat registers, space
heaters, ireplaces, etc.).
• Only use power supply and power cord included with the equipment.
• Equipment should be installed near the power outlet and should be easily accessible.
• The shield of the coaxial cable must be connected to earth (Grounded) at the entrance to the building
in accordance with applicable national electrical installation codes. In the U.S., this is required by NFPA
70 (National Electrical Code) Article 820. In the European Union and in certain other countries, CATV
installation equipment bonding requirements are speciied in IEC 60728-11, Cable networks for television
signals, sound signals and interactive service, Part 11: Safety. This equipment is intended to be installed
in accordance with the requirements of IEC 60728-11 for safe operation.
• In areas of high surge events or poor grounding situations and areas prone to lightning strikes, additional
surge protection may be required on the AC, and Ethernet cables.
Copyright ©2013 SMC Networks. All rights reserved
All information contained in this documentation is subject to change without notice.
Rev 1.1
Nov 2013
DOCSIS 3.0 Wireless Gateway Installation Instructions
Models
The SMC Wireless Gateway comes in one version: D3G2408WE.
Package Contents
•
•
•
•
1 – Wireless Data Gateway
1 – Power Supply and AC Power Cord
1 – CAT-5 Ethernet cable
1 – These Installation Instructions
Installation Overview
1. Connect the coaxial cable from the cable outlet to the Gateway.
2. Connect your wired connections (Ethernet and USB) to the rear panel as shown in the diagram below.
3. Connect the power supply to the Gateway and to a wall power outlet.
WARNING: Use only the provided power supply! Using a different power supply may damage your unit
and void the warranty.
AVERTISSEMENT: Utilisez uniquement la source d’alimentation fournie! L’utilisation d’une autre source
d’alimentation risque d’endommager l’unité et d’annuler la garantie.
4. Conirm the front panel POWER LED is ON.
5. Wait until the DS, US and ONLINE LED stop lashing and the ONLINE LED stays ON indicating that the
device is online. If the ONLINE LED does not go ON in 5 minutes, contact your Internet Service Provider.
6. If your computer or wireless client device supports WPS (Wi-Fi Protected Setup), press the WPS button
on the front panel for 5 seconds to enable WPS.
7. Press the WPS button on your computer or wireless client within 60 seconds to complete association
process. When a client joins the network, the WPS LED stays ON until the next WPS action or the device
reboots. If no client joins, the LED stops blinking after 4 minutes.
NOTE: You must set up your computer and other wireless client devices to work with security settings on
this device. Refer to the documentation for your wireless client devices for instructions on setting security.
8. (Optional): Log in to conigure additional device settings.
• Open a Web browser page and type http://192.168.0.1 in the address bar.
• At the Login screen, enter the following login information:
(NOTE: Username and password are case sensitive.)
Username: admin
Password: password
Detailed user manual can be downloaded from http://na.smc.com.
Copyright ©2013 SMC Networks. All rights reserved
All information contained in this documentation is subject to change without notice.
DOCSIS 3.0 Wireless Gateway Installation Instructions
Wall-Mounting the Gateway
You can mount the Gateway on a wall by hanging the unit along its width using the two wall mount keyhole
slots on the side of the unit.
WARNING: Wall-mount the Gateway to concrete or plaster wallboard with anchor inserts. Before drilling
holes, check the structure for potential damage to water, gas, or electric lines.
AVERTISSEMENT: Montez la passerelle sur une plaque murale en béton ou en plâtre à l’aide de
ixations. Avant de percer des trous, regardez si la structure n’est pas endommagée et assurez-vous de
ne pas percer des conduites d’eau, de gaz ou des lignes électriques.
1. Use 3.5 mm x 40-50 mm (#6 x 1.5-2 in.) pan head
screws with a maximum screw head diameter of
6.5 mm (0.25 in.) to mount the Gateway.
2. Use a center punch to mark the location on the
wall for each mounting screw. The screws must
be oriented horizontal to each other and spaced at
101.6 mm (4 in.) on center.
3. Drill holes to a depth and diameter appropriate for
the size and type of hardware you have selected.
4. Using a screwdriver, turn each screw until the
head protrudes from the wall so that there is a
distance of 12.5 mm (0.5 in.) between the wall and
the underside of the screw head.
5. Orient the Gateway with the mounting keyholes
above the mounting screws, and then slide the
Gateway down so it stops against the top of the
keyhole opening.
6. Reconnect the coaxial cable and Ethernet cables.
Reconnect the power cord to the Gateway and the
electrical outlet.
Copyright ©2013 SMC Networks. All rights reserved
All information contained in this documentation is subject to change without notice.
DOCSIS 3.0 Wireless Gateway Installation Instructions
GPL / GNU License
This product includes software code developed by third parties, including software code subject to the GNU
General Public License (“GPL”) or GNU Lesser General Public License (LGPL”). As applicable, the terms of the
GPL and LGPL, and information on obtaining access to the GPL code and LGPL used in this product, are available to you at http://gpl.smc.com/. The GPL code and LGPL code used in this product is distributed WITHOUT
ANY WARRANTY and is subject to the copyrights of one or more authors. For details, see the GPL Code and
LGPL Code for this product and the terms of the GPL and LGPL.
Compliance Statements
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modiications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Avertissement de la FCC: Toute modiication apportée non expressément approuvée par l’entité
responsable de la conformité pourrait annuler le droit de l’utilisateur à utiliser cet équipement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
Copyright ©2013 SMC Networks. All rights reserved
All information contained in this documentation is subject to change without notice.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2013:11:28 17:39:20+08:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2015:03:17 16:43:53+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Instance ID                     : uuid:457650c9-ca55-49ba-bede-e735b0ad0c6a
Original Document ID            : adobe:docid:indd:774d33d6-b6f2-11e2-a597-e95d44aa4c6b
Document ID                     : xmp.id:F55969D01058E311A4AC8BF54564D27B
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:F45969D01058E311A4AC8BF54564D27B
Derived From Document ID        : xmp.did:3A3619E0CF16E3119895DB60360D569F
Derived From Original Document ID: adobe:docid:indd:774d33d6-b6f2-11e2-a597-e95d44aa4c6b
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2013:11:28 17:39:20+08:00
Metadata Date                   : 2015:03:17 16:43:53+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
State                           : 1
Version                         : 1.1
Page Layout                     : TwoPageRight
Page Mode                       : UseThumbs
Page Count                      : 4

EXIF Metadata provided by EXIF.tools