SPRINGCARDS MODK531232 RFID Module User Manual DETAILED VIEWS

Pro Active SAS RFID Module DETAILED VIEWS

User Guide

pftd2501-ae.doc03/09/2004 SRK-K531 : OEM 14443-A READER STARTER KIT Version : AE Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of PRO ACTIVE. PRO ACTIVE and the PRO ACTIVE logo are registered trademarks of PRO ACTIVE S.A.R.L. MIFARE and Philips areregistered trademarks of Philips. DATASHEET SRK-K531 : OEM 14443-A READER STARTER KIT 2/2 PRO ACTIVE phone. : +33 1 64 53 20 10 S.A.R.L. capital of 100 000€ PARC GUTENBERG Fax : +33 1 64 53 20 18 R.C.S. EVRY B 429 665 482 13 VOIE LA CARDON A.P.E. 722Z F-91120 PALAISEAU mail : info@pro-active.fr VAT #. FR27 429 665 482 00015 France web : www.pro-active.fr RS232 OPERATIONS The OEM 14443-A Reader Starter Kit can operate with a RS232 terminal such as HyperTerminal. RS232 Parameters........Transmission Speed : 38400, Parity : none, Data : 8, Stop : 1 AVAILABLES COMMANDS Info ................................Retrieve version and RC chipset ID poll.................................Poll for 14443-A tags (ESC to quit) tag .................................Select Mifare or 14443-A tag read ...............................Read Mifare 1k or 4k tag halt ................................Mifare or 14443-A halt command reset ..............................Reset the module help................................Display a list of some availables commands rf_on ..............................Activate the RF field rf_off..............................De-activate the RF field rc_on .............................Open access to the RC chipset rc_off .............................Close access to the RC chipset rc_reset .........................Reset the RC chipset rc_config.......................Configure the chipset with startup values tcl_rats ..........................Open a T=CL 14443-A session tcl_stop .........................Send the T=CL 14443-A « deselect » tcl_pps ..........................Send a T=CL 14443-A PPS request keys ...............................Load default keys to RC RAM keys_e2 .........................Load default keys to RC EEPROM keys[A|B]n=(key_data) .keys command immidiatly followed by key type ‘A’ or ‘B’ and index of this key from ‘0’ to ‘F’. (key_data) can be 12 bytes in hexadecimal, or 6 letters. regs ...............................Display RC register values led=RG[Y]......................Control leds outputs, where R, G and optionnaly Y are to be replaced a number between 0 and 3 : 0 : Off 1 : On 2 : Fast blink 3 : Slow blink (for MOD-K531_OEM) 3 : Default action (for MOD-K531_CSB4) 115200........................... Switch the module to high speed communication. 38400............................. Switch the module to normal speed communication. const=(configuration_structure_data) Where the structure data is : Serial configuration BYTE PBK PNS RFU SBO SOD SEO SNC SHB MSB LSB PBK ...............................Blink LEDs before any action from host if set to 1 PNS ...............................WARNING ! CURRENT ACTION CAN NOT BE INTERRUPTED IF SET TO 1. ALWAYS SET THIS BIT TO ZERO. RFU ............................... Reserved for future use. SBO............................... Use binary protocol in bus mode only if set to 1 SOD............................... Don't use OSI protocol if set to 1 SEO ............................... No serial echo if set to 1 SNC ...............................Serial speed can't be changed by software if set to 1 SHB ...............................Startup in high speed if set to 1 Address to be used in multi-point protocol BYTE Action to be entered on startup BYTE RFU BYTE SEQUENCE EXAMPLES Read a tag .....................1 . Present a 14443-A or MIFARE® tag in the antenna area. 2 . keys 3 . tag Î You should obtain specific data of your tag (Serial number, ATQ, SAK) 4 . read Î You should obtain the content of the differents sectors of the tag. Store a key ....................To store the key 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF as key B in position 2 : keysB2=FFFFFFFFFFFF Configure LEDS............To switch on the green LED switch off the yellow LED and make the red LED blinking fast : led=210 Polling at Startup..........To ensure a continuous polling of any tag at startup enter the following command then rebooting the module : const=00004F00 reset Recover default configuration Hit “Enter” key until “>” appears const=00000000 reset SOFTWARE OPERATIONS The starter kit need the “SpringProx.dll” to operate with the samples applications. This DLL and demonstration softwares are availables on our web site at : http://www.pro-active.fr/download/csb Availables samples applications are : MIFARE Tool................. Allow you to select read / write your contactless cards. Electronic Purse Tool... Demonstration of counter on a MIFARE® 1K contactless card. SPECIFIC DEVELOPMENTS A specific firmware for the OEM 14443-A Reader Module is available, giving instant MIFARE® Tag ID reading on the RS232 line. For more details ask Pro-Active for the Application Note : PMXZ010. REGISTRATION To obtain 3 months technical support and the source code package, please send us an e-mail to this electronic address : srk@pro-active.fr Please, send us your :.... company name, name and address, the serial number of your SRK-K531. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu