SRM Service Center PM6 PowerMeter 6 User Manual pm short manual 30 5 08

Download:
Mirror Download [FCC.gov]
Document ID	957481
Application ID	yVbZCH8Vs0h7VVJG/Sec5g==
Document Description	Exhibit 8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.03kB (150326 bits)
Date Submitted	2008-06-18 00:00:00
Date Available	2008-06-18 00:00:00
Creation Date	2008-05-30 15:00:06
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2008-06-16 15:41:02
Document Title	Microsoft Word - pm short manual 30_5_08
Document Creator	PScript5.dll Version 5.2.2
Document Author:	prosenland

PowerMeter Getting Started 30. Mai 2008
The SRM Wireless Training System road Shimano Dura-Ace 10-speed compatible
Specification:
PowerMeter (power measurement unit)
Number of strain gauge stripes:
Measurement accuracy:
±2%
Data transmission:
Wireless:
Cable:
ANT+sports protocol
inductive, coil
Life span of battery:
1.500 hours
Shimano Dura-Ace 10 speed crank:
Cranks are available in lengths between 165 and 180mm
Integrated Axle Shimano Dura Ace FC7800
Chainrings:
Weight:
Bolt circle diameter:
Chainring:
130mm
53/39
other chainring combinations on request
812g (incl. cranks, chainrings and axle)
Compatible with SRM PowerControl IV, V and VI
This PowerMeter is only available in the Professional Road version.
Installation of the front chainwheel
Schoberer Rad Messtechnik GmbH
Rudolf Schulten Str. 6
D-52428 Jülich
Tel.: +49 (2461) 69123-0
Fax:+49 (2461) 69123-17
www.srm.de
SRM Service Center Inc.
720 West Monument Street
Colorado Springs, CO 80904
USA
Tel.: +1 (719) 266 4127
Fax: +1 (710) 266 4284
PowerMeter Getting Started 30. Mai 2008
Sensor magnet mounting instructions
To mount the sensor magnet, remove the cable guide bolt and the cable guide below
the bottom bracket.
Either remove the cable guide or slacken the cables to put the sensor cable between
the guide and bottom bracket.
Adjust the sensor and then tighten the guide and bolt back on.
Important: Mount the sensor below the cable guide! Front and rear derailleur need to
be adjusted if necessary!
The sensor cable housing has a long slit to adjust the distance to the lid of the
Powermeter. It is essential that the clearance to the lid is at least 2-3 mm to prevent
interferences or incorrect measurements.
Lastly, check to make sure you receive cadence and a zero offset as described in the PowerControl VI Short
Manual. If the sensor cable moves you can use double stick tape to fix it to the bottom bracket.
Important Safety Instructions
After riding approximately 100 km (60 miles), use a torque wrench to re-check the tightening torques.
Please check
• on regular basis:
o the tightening torques
o that the tension of the chain is correct and that the chain is not damaged.
• before every ride:
o that there are no cracks in the crank arms
Damages on the chain or the crank arm can cause that you fall off the bicycle, serious injuries or even death.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and may cause
harmful interference to radio communications if not installed and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver
•
Connect the equipment into an outlet that is on a different circuit from GPS unit.
•
Consult the dealer or an experienced radio/TV technician for help.
This product does not contain any user-serviceable parts. Repairs should only be made by an authorized SRM
service center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and void
your warranty and your authority to operate this device under Part 15 regulations.
Schoberer Rad Messtechnik GmbH
Rudolf Schulten Str. 6
D-52428 Jülich
Tel.: +49 (2461) 69123-0
Fax:+49 (2461) 69123-17
www.srm.de
SRM Service Center Inc.
720 West Monument Street
Colorado Springs, CO 80904
USA
Tel.: +1 (719) 266 4127
Fax: +1 (710) 266 4284

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2008:05:30 15:00:06Z
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:06:16 15:41:02-06:00
Metadata Date                   : 2008:06:16 15:41:02-06:00
Format                          : application/pdf
Creator                         : prosenland
Title                           : Microsoft Word - pm short manual 30_5_08
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:6f97f3f3-8866-493b-884a-17fce9067c10
Instance ID                     : uuid:32d5f558-4ac2-4c95-8806-d025522eaa92
Page Count                      : 2
Author                          : prosenland

EXIF Metadata provided by EXIF.tools